
Pi485
bvarner/pi485
An open-source TTL UART <-> RS485 converter, intended for a Raspberry Pi or Arduino

A 2-channel CV to DMX converter for use with a modular synthesiser
CV to DMX is an open-source printed circuit board by clarionut, from the clarionut/Scriabin_CV-DMX repository on GitHub. It is a 2-layer board of 96.5 × 73 mm with 95 parts on 69 nets, routed with 377 tracks and 4 vias.
It is built around the MAX485ED and BAT43. Its parts include 46 resistors, 16 capacitors, 12 diodes, 9 connectors and 4 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
A two channel CV-DMX converter based on an Arduino Pro Mini microcontroller.
Named for the famously synaesthetic composer Scriabin, this module was designed to allow RGB LED PAR cans to be voltage controlled by an analogue modular synthesiser. Each of the two channels can be controlled in the RGB (red, green, blue) or HSV (hue, saturation, value) colourspace, giving three control inputs per channel. Each individual input has an attenuator for the CV input and an initial value potentiometer, so all colours are accessible without using the CV inputs. In RGB mode the inputs control the red, green and blue channels individually, simple to understand but harder to use. Consequently HSV is probably the more useful colourspace, where setting the saturation and value initial values to maximum allows all hues to be accessed using just one CV input. This is also the reason for using HSV rather than the HSL (hue, saturation, lightness) colourspace, where the fully saturated colours are found at 100% saturation, 50% lightness.
There is also a 'hidden' mode on each channel (hidden mainly because of lack of space on the panel!). With the mode switch in the centre-off position the corresponding channel will enter 'Scriabin mode' which converts the incoming Red/Hue CV into quantised light colours according to the scheme used by Scriabin in his 'Clavier à lumières'. The colours are: C - red; C# - purple; D - yellow; D# - flesh; E - sky blue; F - deep red; F# - bright blue; G - orange; G# - lilac; A - green; A# - rose; B - blue (this makes more sense if ordered by the circle of fifths - C - red; G - orange; D - yellow; A - green; E - sky blue; B - blue; F# - bright blue; C# - purple; G# - lilac; D# - flesh; A# - rose; F - deep red). In this mode the input CV range should be adjusted so that successive octaves give the same colour. The tracking isn't perfect but should be good over about 2 1/2 octaves. The Green/Saturation control has no effect in this mode but the Blue/Value control can be used to fade the light in and out, though the colours are increasingly inaccurate at low brightness.
The hardware is based on an Arduino Pro Mini driving a MAX485 RS-485 transceiver chip, as used in some of the commercial Arduino DMX shields. The CV inputs have protection against out-of-range voltage inputs, but there is no isolation on the MAX485 (again like many of the commercial DMX shields). Consequently the synthesiser and the light units must be powered from the same electrical circuit to avoid potentially dangerous voltages entering the synth.
The KiCad schematic and board layout use some custom symbols and footprints, so you will need to add my kiCad_libraries before using these files.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 100k | CGE_footprints:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5, R15, R17, R18, R25, R27, R28, R33, R35, R36, R41, R43, R44, R49, R51, R52 +2 |
| 12 | 200k | CGE_footprints:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3, R4, R11, R14, R23, R24, R31, R32, R39, R40, R47, R48 |
| 12 | BAT43 | CGE_footprints:D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 9 | 10k | CGE_footprints:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R9, R12, R13, R20, R21, R29, R37, R45 |
| 7 | 100n | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C2, C5, C6, C7, C11, C12, C13 |
| 6 | 10n | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C1, C3, C4, C14, C15, C16 |
| 6 | 47k | CGE_footprints:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R6, R16, R26, R34, R42, R50 |
| 3 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C8, C9, C10 |
| 3 | FB | Inductor_THT:L_Axial_L5.3mm_D2.2mm_P7.62mm_Horizontal_Vishay_IM-1 | FB1, FB2, FB3 |
| 3 | TL074 | Package_DIP:DIP-14_W7.62mm_Socket | U1, U2, U3 |
| 1 | +12V | TestPoint:TestPoint_THTPad_1.5x1.5mm_Drill0.7mm | +12V |
| 1 | 120R? | CGE_footprints:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R19 |
| 1 | Arduino_Pro_Mini | CGE_footprints:Arduino_Pro_Mini | A1 |
| 1 | CHNL1 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | CHNL2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | CHNL3 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | CHNL4 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J10 |
| 1 | CHNL5 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J12 |
| 1 | CHNL6 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J14 |
| 1 | DMX | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J16 |
| 1 | LOGO | CGE_footprints:CGE_logo | G*** |
| 1 | MAX485E | Package_DIP:DIP-8_W7.62mm_Socket | U4 |
| 1 | POWER | CGE_footprints:Power_2x06 | J9 |
| 1 | RESET/MODE | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
The 93 most common of 95 parts.

bvarner/pi485
An open-source TTL UART <-> RS485 converter, intended for a Raspberry Pi or Arduino

VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group



ravinrabbid/DonCon2040
RP2040 based firmware and hardware for DIY Taiko no Tatsujin Drum Controllers

Testbild-synth/HAGIWO_arduino_oscillator
4HP through hole version of the HAGIWO FM/additive/chord oscillator with mode switch and gain input.

Testbild-synth/Hagiwo_009_030_sequencer
A through-hole PCB conversion of HAGIWO's 6 channel eurorack gate sequencer. Includes Gerbers, Code and building instructions.

Testbild-synth/HAGIWO-029-033-Eurorack-quantizer
Through hole PCB version of the HAGIWO Dual Quantizer/SH101 Sequencer Eurorack Module-.
It measures 96.5 × 73 mm and has 2 copper layers, 1.6 mm thick.
95 parts, built around the MAX485ED and BAT43. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the clarionut/Scriabin_CV-DMX repository on GitHub, at the commit this page was made from: the board is Schematics/CV_to_DMX.kicad_pcb and its schematic Schematics/CV_to_DMX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask clarionut before reusing the design.