2 layers50 × 50 mm
Filmolino
filmolino/SlideScanner
The Filmolino SlideScanner is a device that makes it easy to scan slides in magazines fully automated using a modified slide projector and a digital camera.
37 parts28GPL-3.0
2 layers95 × 80 mm
Electrolumino rev0
cl0rm/ElectroLumino1Portable Mulit-Channel programmable EL wire driver featuring PWM
- Size
- 95 × 80 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 90
- Nets
- 82
- Pads
- 271
- Tracks, vias
- 415, 51
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 5 May 2024
- Updated
- 15 Jul 2024
Overview
Electrolumino rev0 is an open-source printed circuit board by cl0rm, from the cl0rm/ElectroLumino repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 95 × 80 mm with 90 parts on 82 nets, routed with 415 tracks and 51 vias.
It is built around the WEMOS D1 MINI, HV857MG-G and BAS21. Its parts include 27 resistors, 25 capacitors, 10 ICs, 8 diodes and 8 connectors. It belongs with the ESP8266 boards of this library.
Main components
3
WEMOS D1 MINI
A mini wifi board with 4MB flash based on ESP-8266EX, hardware version 4.0.0.LolinUncategorised
HV857MG-G
MSOP-8-40℃~+85℃ 1.8V~5V 190V 300mW 80kHz EL Lamp Driver MSOP-8 Lighting Drivers & Controllers ROHSMicrochip TechnologyLighting Drivers & Controllers
BAS21
SOT-231.25V@200mA 100nA@100V 200mA 250V 9A Independent SOT-23 Diodes - General Purpose ROHSNexperiaSwitching Diodes
README
README.mdElectroLumino
Portable Mulit-Channel programmable EL wire driver featuring PWM
Warning
EL Wire is driven with rather high voltages. Only play with high voltages if you know what you're doing!
Idea
This will become a fancy EL wire driver to make shiny clothing. It should fit into a pocket (so it will be more or less the size of a typical smart phone)
Features
-
Battery Powered (18650 Cell)
-
USB rechargable
-
Up to four different EL wire channels
-
PWM dimming
-
Audio Reactive
-
Additional WSxxx Digital LED channel
Parts
90| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 4.7uF 6.3V | Capacitor_SMD:C_0603_1608Metric | C3, C4, C7, C10, C13, C16, C19, C22, C25 |
| 8 | 100nF 6.3V | Capacitor_SMD:C_0603_1608Metric | C2, C5, C8, C11, C14, C17, C20, C23 |
| 8 | 2.0M | Resistor_SMD:R_0603_1608Metric | R7, R11, R14, R17, R20, R23, R26, R29 |
| 8 | 220uH | Inductor_SMD:L_Changjiang_FNR3015S | L1, L2, L3, L4, L5, L6, L7, L8 |
| 8 | 3.3nF 100V | Capacitor_SMD:C_0603_1608Metric | C1, C6, C9, C12, C15, C18, C21, C24 |
| 8 | 560k | Resistor_SMD:R_1206_3216Metric | R8, R9, R12, R15, R18, R21, R24, R27 |
| 8 | 560k | Resistor_SMD:R_0603_1608Metric | R6, R10, R13, R16, R19, R22, R25, R28 |
| 8 | BAS21 | Package_TO_SOT_SMD:SOT-23 | D1, D2, D3, D4, D5, D6, D7, D8 |
| 8 | HV857MG-G | Package_SO:MSOP-8_3x3mm_P0.65mm | U3, U4, U5, U6, U7, U8, U9, U10 |
| 8 | JST PH series | Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J1, J2, J3, J4, J5, J6, J7, J8 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 2k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | Battery | Battery:BatteryHolder_MPD_BH-18650-PC2 | BT1 |
| 1 | MCP73812T-435I-OT | Package_TO_SOT_SMD:SOT-23-5 | U11 |
| 1 | SW_Push | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx31-2LFS | SW1 |
| 1 | WeMos_D1_mini | Module:WEMOS_D1_mini_light | U1 |
Similar boards
- 2 layers80 × 38.1 mm
- 4 layers252 × 152 mm
CTA control board
PySpice-org/eda-rw
Python library to read/write KiCad and LibrePCB Sexpr file format
619 parts9 - 2 layers83.5 × 97.5 mm
TeleprinterHat
MattisLind/teleprinterHat
A RaspberryPi HAT that interfaces a old school teleprinter
145 parts6 - 4 layers240 × 90.5 mm
BILLEE Rover Control Module V1
BILLEE-BroncoSTAR/billee-hardware-2027
Hardware and firmware Repository for BILLEE URC 2027
276 parts1MIT - 2 layers91 × 87 mm
- 6 layers105.6 × 100.9 mm
- 2 layers50.2 × 19.4 mm
Questions
How big is the Electrolumino rev0 PCB?
It measures 95 × 80 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Electrolumino rev0 use?
90 parts, built around the WEMOS D1 MINI, HV857MG-G and BAS21. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Electrolumino rev0 KiCad files?
From the cl0rm/ElectroLumino repository on GitHub, at the commit this page was made from: the board is hardware/electrolumino_rev0/electrolumino_rev0.kicad_pcb and its schematic hardware/electrolumino_rev0/el_drv.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Electrolumino rev0 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).