Skip to the content
2 layers59 × 52 mmDots, the printed circuit board in 3D

multiplexing led matrix

Size
59 × 52 mm
Copper layers
2
Thickness
1.6 mm
Parts
25
Nets
41
Pads
83
Tracks, vias
99, 0
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
9 Jul 2024
Updated
9 Jul 2024

Overview

Dots is an open-source printed circuit board by circles-png, from the circles-png/dots repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 59 × 52 mm with 25 parts on 41 nets, routed with 99 tracks and 0 vias.

It is built around the ARDUINO UNO R3. Its parts include 15 diodes, 6 resistors and 3 transistors. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

dots

Rust project for the Arduino Uno.

Build Instructions

  1. Install prerequisites as described in the avr-hal README (avr-gcc, avr-libc, avrdude, ravedude).

  2. Run cargo build to build the firmware.

  3. Run cargo run to flash the firmware to a connected board. If ravedude fails to detect your board, check its documentation at https://crates.io/crates/ravedude.

  4. ravedude will open a console session after flashing where you can interact with the UART console of your board.

License

Licensed under either of

at your option.

Contribution

Unless you explicitly state otherwise, any contribution intentionally submitted for inclusion in the work by you, as defined in the Apache-2.0 license, shall be dual licensed as above, without any additional terms or conditions.

Parts

25
QtyValueFootprintReferences
15LED_45degLED_THT:LED_D3.0mmD1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15
31kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R3, R5
32.2kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R4, R6
3Q_PNP_ECBPackage_TO_SOT_THT:TO-92_InlineQ1, Q2, Q3
1Arduino_UNO_R3Module:Arduino_UNO_R3A1

Similar boards

  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0
  • 2 layers69.1 × 53.8 mmMotor controller, the printed circuit board in 3D

    Motor controller

    AlanFord/self-balancing-stick

    Dual Axis Reaction Wheel Inverted Pendulum

    25 parts79MIT
  • 2 layers68.6 × 53.3 mmProtogasm Board V2, the printed circuit board in 3D

    Protogasm Board V2

    Edging-Machines/Edging-Machines

    This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

    14 parts67MIT
  • 2 layers53.8 × 69.6 mmEVSE V2 2, the printed circuit board in 3D

    EVSE V2 2

    PedroCNeves/AC_ChargingStation

    A learning project to create an EV AC Charging station based on an Arduino Uno

    32 parts50
  • 2 layers113.7 × 61 mmArduTester SMD, the printed circuit board in 3D

    ArduTester SMD

    jonsag/arduTester

    An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4

    17 parts14
  • 4 layers65.9 × 52.9 mmMotor shield, the printed circuit board in 3D

    Motor shield

    DCC-EX/EX-MotorShield8874

    Design files for the open source 5A Motor Shield

    114 parts12
  • 4 layers68.6 × 53.3 mm101 PCB, the printed circuit board in 3D

    101 PCB

    ICRS/101

    The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.

    89 parts10CC-BY-4.0
  • 2 layers53.3 × 68.3 mmAnac 2040, the printed circuit board in 3D

    Anac 2040

    rallekralle11/Anna2040

    RP2040-based board in the shape of the Arduino uno

    63 parts9

Questions

How big is the Dots PCB?

It measures 59 × 52 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Dots use?

25 parts, built around the ARDUINO UNO R3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Dots KiCad files?

From the circles-png/dots repository on GitHub, at the commit this page was made from: the board is dots/dots.kicad_pcb and its schematic dots/dots.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Dots design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).