
Relatively Universal ROM Programmer
AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

multiplexing led matrix
Dots is an open-source printed circuit board by circles-png, from the circles-png/dots repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 59 × 52 mm with 25 parts on 41 nets, routed with 99 tracks and 0 vias.
It is built around the ARDUINO UNO R3. Its parts include 15 diodes, 6 resistors and 3 transistors. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.
Rust project for the Arduino Uno.
Install prerequisites as described in the avr-hal README (avr-gcc, avr-libc, avrdude, ravedude).
Run cargo build to build the firmware.
Run cargo run to flash the firmware to a connected board. If ravedude
fails to detect your board, check its documentation at
https://crates.io/crates/ravedude.
ravedude will open a console session after flashing where you can interact
with the UART console of your board.
Licensed under either of
at your option.
Unless you explicitly state otherwise, any contribution intentionally submitted for inclusion in the work by you, as defined in the Apache-2.0 license, shall be dual licensed as above, without any additional terms or conditions.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | LED_45deg | LED_THT:LED_D3.0mm | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15 |
| 3 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3, R5 |
| 3 | 2.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4, R6 |
| 3 | Q_PNP_ECB | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2, Q3 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3 | A1 |

AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

AlanFord/self-balancing-stick
Dual Axis Reaction Wheel Inverted Pendulum

Edging-Machines/Edging-Machines
This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

PedroCNeves/AC_ChargingStation
A learning project to create an EV AC Charging station based on an Arduino Uno

jonsag/arduTester
An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4


ICRS/101
The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.

It measures 59 × 52 mm and has 2 copper layers, 1.6 mm thick.
25 parts, built around the ARDUINO UNO R3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the circles-png/dots repository on GitHub, at the commit this page was made from: the board is dots/dots.kicad_pcb and its schematic dots/dots.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).