
MCU Datalogger
futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.

MCU Datalogger is an open-source printed circuit board by chopda15, from the chopda15/MCU-datalogger_2-layer repository on GitHub. It is a 2-layer board of 50.2 × 30.5 mm with 30 parts on 36 nets, routed with 402 tracks and 20 vias.
It is built around the ATMEGA328PB-AU, 24LC1025-I/P and DS1337S+T&R. Its parts include 7 resistors, 5 capacitors, 4 ICs, 4 connectors and 2 diodes. It belongs with the sensors and measurement boards and the AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1, C4 |
| 2 | 10K | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | 24LC1025 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1, U2 |
| 2 | 330 | Resistor_SMD:R_0805_2012Metric | R5, R7 |
| 2 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1, J2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D1, D2 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 10Khz | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 16Mhz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y2 |
| 1 | 32.786KHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | 4.7 | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 4.7K | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | ATMEGA328PB-AU | digikey-footprints:TQFP-32_7x7mm | U3 |
| 1 | Battery | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | BT1 |
| 1 | Conn_01x09_Pin | Connector_PinSocket_2.54mm:PinSocket_1x09_P2.54mm_Vertical | J3 |
| 1 | Conn_02x03_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Vertical | J4 |
| 1 | DS1337S_ | DS1337S_:SOIC127P600X175-8N | U4 |
The 29 most common of 30 parts.

futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.

futureshocked/KicadLikeAPro-Project-3-BACEE
This is one of the PCB projects from the Kicad Like a Pro book. It contains a two and four layer board that implements an Arduino clone with external EEPROM and a clock.

DevMajed/DataLogger-Board
Hardware PCB Design for AVR-based Datalogger using KiCAD



elCowboyLuigi/MCU_datalogger_project_study
This is a PCB project of a MCU Datalogger with EEPROM and Clock from section 11 of PCB Design with Kicad course for use as a learning experience

GildardoRestrepo/course_electronics_design
Repositorio de actividades entregables del curso de diseño electrónico. UPB 2026-02

lologog/MCU_DataLogger
A microcontroller-based device for logging and storing data from external sensors. The data is saved to EEPROM memory for later retrieval and analysis
It measures 50.2 × 30.5 mm and has 2 copper layers, 1.6 mm thick.
30 parts, built around the ATMEGA328PB-AU, 24LC1025-I/P and DS1337S+T&R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the chopda15/MCU-datalogger_2-layer repository on GitHub, at the commit this page was made from: the board is MCU Datalogger/MCU Datalogger.kicad_pcb and its schematic MCU Datalogger/MCU Datalogger.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask chopda15 before reusing the design.