
OpenEMG2
CGrassin/OpenEMG
OpenEMG is an open-hardware, easy to make, EMG module to measure muscle activity.

OpenEMG is an open-hardware, easy to make, EMG module to measure muscle activity.
OpenEMG2 is an open-source printed circuit board by CGrassin, from the CGrassin/OpenEMG repository on GitHub, published under the MIT licence. It is a 2-layer board of 33.7 × 47 mm with 31 parts on 25 nets, routed with 110 tracks and 0 vias.
It is built around the ICL7660N and LM324. Its parts include 15 resistors, 7 capacitors, 4 connectors, 2 ICs and 1 diode.
Electromyography (EMG) is a commonly used electrodiagnostic medicine technique for evaluating and recording the electrical activity produced by skeletal muscles. OpenEMG is a project that aims to create an open-source, easy-to-make EMG module that can capture muscle information from Arduino or any other micro-controller. With this module, users can measure muscle activity and use the data to explore various applications such as robotics and prosthetics.
View the article about this project (including performance, usage, principle of operation) here: https://charleslabs.fr/en/project-OpenEMG+Arduino+Sensor
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2, R9, R10, R13 |
| 3 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C6, C8, C9 |
| 3 | 18k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R7, R11, R15 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R8, R12 |
| 2 | 15k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5, R6 |
| 2 | 330n | Capacitor_THT:C_Rect_L7.0mm_W3.5mm_P5.00mm | C3, C4 |
| 2 | 470n | Capacitor_THT:C_Rect_L7.0mm_W3.5mm_P5.00mm | C1, C2 |
| 2 | 47k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R4 |
| 2 | Mounting_hole | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | J5, J6 |
| 1 | 100k | Potentiometer_THT:Potentiometer_Bourns_3266Y_Vertical | RV1 |
| 1 | 1N4148 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | D1 |
| 1 | 47k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R14 |
| 1 | Electrodes | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | ICL7660 | Package_DIP:DIP-8_W7.62mm_LongPads | U2 |
| 1 | LM324 | Package_DIP:DIP-14_W7.62mm_LongPads | U1 |
| 1 | Logo_Open_Hardware_Small | Symbol:OSHW-Logo2_7.3x6mm_SilkScreen | LOGO1 |
| 1 | MCU_out | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |

CGrassin/OpenEMG
OpenEMG is an open-hardware, easy to make, EMG module to measure muscle activity.

leikoilja/muscle-imbalance-detection
A device to assist patients with the rehabilitation of the knee joint after a knee surgery using EMG biofeedback. The device can reliably detect muscle activity and display it in an easy-to-use mobile application.


lynchaj/duodyne
Duodyne is a hobbyist retrocomputer system designed to run ROMWBW. It is comprised of modules on a system bus


GadgetReboot/Phone_SLIM
POTS Telephone Subscriber Line Interface Module

BojanSof/BluePillWaveGen
DDS function generator build around STM32 BluePill board

tvlad1234/osillyscope
Low cost, low part count CH32V003-based oscilloscope

SamsungSLAV/muxpi
MuxPi is an open hardware and open software board which was designed to aid in automating tasks on physical devices.
It measures 33.7 × 47 mm and has 2 copper layers, 1.6 mm thick.
31 parts, built around the ICL7660N and LM324. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the CGrassin/OpenEMG repository on GitHub, at the commit this page was made from: the board is OpenEMG_THT/OpenEMG2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).