Skip to the content
2 layers23 × 16 mmAmplifiers, the printed circuit board in 3D

Remake of the board of the 5-th EPO (2017), using KiCAD 7.0, to measure the Boltzmann constant through the analysis of the thermal noise of a resistor.

Size
23 × 16 mm
Copper layers
2
Thickness
1.6 mm
Parts
4
Nets
8
Pads
21
Tracks, vias
28, 9
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
7 Feb 2024
Updated
25 Aug 2024

Overview

Amplifiers is an open-source printed circuit board by CarlosCraveiro, from the CarlosCraveiro/einstein-boltzmann repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 23 × 16 mm with 4 parts on 8 nets, routed with 28 tracks and 9 vias.

It is built around the ADA4898-2YRD. Its parts include 3 connectors and 1 IC. It belongs with the audio and music boards of this library.

Main components

1

README

README.md

The Einstein-Boltzmann Board

main_board_other_view

Project's Intent

Measure the Boltzmann constant through the analysis of the thermal noise of a resistor.

Disclaimer

This Board was intended to be used with the Guide of the 5-th EPO (2017).

So the schematic ideia is not mine, I just adapt and documented it so I could manufacture the board.

The DRC Custom Rules used on this project came from a gist made by darkxst, Gist name: rules.txt.

Project's Dependencies

If you use nix, to have access to KiCAD 7.0, on the project's directory type:

shell
nix --experimental-features 'nix-command flakes'
nix develop -c $SHELL

Preview Images

Main Board

main_board_front main_board_back

Modules

tension-multiplier_front tension-multiplier_module amplifiers_module amplifiers_back

Real Photos

main-board_front main-board_back

TO DO...

  • Finish soldering the components and modules
  • Create a Wiki for the project
  • Measure the Boltzmann constant and publish the results on the project's Wiki
  • Finish the plate support base (using FreeCAD)
  • Write a theoretical introduction about the phenomenon on the project's Wiki

Observation: I intend to continue working on the project, I just need time.

Additional information:

I talked about the project at the FOSFORUMS 2024 event. The presentation were in English and both the slides and the link for the presentation recording could be access here.

Parts

4
QtyValueFootprintReferences
2Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1, J3
1ADA4898-2Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.81mmU1
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2

More from CarlosCraveiro/einstein-boltzmann

2
  • 2 layers161.8 × 100 mmEinstein boltzmann, the printed circuit board in 3D

    Einstein boltzmann

    CarlosCraveiro/einstein-boltzmann

    Remake of the board of the 5-th EPO (2017), using KiCAD 7.0, to measure the Boltzmann constant through the analysis of the thermal noise of a resistor.

    63 parts1CERN-OHL-S-2.0
  • 2 layers23 × 16 mmTension multiplier, the printed circuit board in 3D

    Tension multiplier

    CarlosCraveiro/einstein-boltzmann

    Remake of the board of the 5-th EPO (2017), using KiCAD 7.0, to measure the Boltzmann constant through the analysis of the thermal noise of a resistor.

    4 parts1CERN-OHL-S-2.0

Similar boards

  • 2 layers20 × 30 mmSFH203 photodetector, the printed circuit board in 3D

    SFH203 photodetector

    TU-Darmstadt-APQ/SFH203_photodetector

    Low-noise transimpedance amplifier optimized for the photodiode SFH203.

    19 parts8
  • 2 layers160 × 100 mmMTS module, the printed circuit board in 3D

    MTS module

    TU-Darmstadt-APQ/MTS_module

    Module for AOM-based modulation transfer spectroscopy (MTS) signal generation.

    131 parts3
  • 2 layers100 × 100 mmADA4898 LNA, the printed circuit board in 3D

    ADA4898 LNA

    aewallin/ADA4898_LNA

    Low Noise Amplifier based on ADA4898

    618 parts2
  • 2 layers160 × 100 mmPDH module, the printed circuit board in 3D

    PDH module

    TU-Darmstadt-APQ/PDH-module

    Produces a PDH error-signal using MiniCircuits SYPD-1+ phase detector and LT1568 4th order low-pass filter. To be used with a AD9959 DDS board.

    85 parts2
  • 2 layers18.5 × 26 mm24g2usb rp2350zero, the printed circuit board in 3D

    24g2usb rp2350zero

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    4 parts1.7kApache-2.0
  • 2 layers116 × 33 mm966595-1 and 963356-1, the printed circuit board in 3D

    966595-1 and 963356-1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    4 parts1.2k
  • 2 layers19 × 18 mmDaughter board, the printed circuit board in 3D

    Daughter board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    4 parts915

Questions

How big is the Amplifiers PCB?

It measures 23 × 16 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Amplifiers use?

4 parts, built around the ADA4898-2YRD. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Amplifiers KiCad files?

From the CarlosCraveiro/einstein-boltzmann repository on GitHub, at the commit this page was made from: the board is amplifiers/amplifiers.kicad_pcb and its schematic amplifiers/amplifiers.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Amplifiers design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).