2 layers65 × 65 mm
4 layers40 × 40 mm
CertusNX
c4tsnest/certus_test- Size
- 40 × 40 mm
- Copper layers
- 4
- Thickness
- 1.59 mm
- Parts
- 125
- Nets
- 181
- Pads
- 636
- Tracks, vias
- 1,358, 251
- Pours
- 20
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 19 Aug 2025
- Updated
- 12 Sep 2025
Overview
CertusNX is an open-source printed circuit board by c4tsnest, from the c4tsnest/certus_test repository on GitHub. It is a 4-layer board of 40 × 40 mm with 125 parts on 181 nets, routed with 1,358 tracks and 251 vias.
It is built around the LFD2NX-17-7MG121I, TPSM53604RDA and TLV62569ADRL, with the W25Q128JVPIQ and FT2232HQ among its other parts. Its parts include 48 capacitors, 40 resistors, 8 ICs, 7 diodes and 5 connectors.
Main components
5
LFD2NX-17-7MG121I
CSFBGA-121(6x6)-40℃~+100℃ 0.95V~1.05V 17000 4250 433152bit 71 Certus-NX CSFBGA-121(6x6) Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)
TPSM53604RDA
DFN143.8V to 36V Input, 1V to 7V Output, 4A Power Module in Enhanced HotRod™Texas InstrumentsUncategorised
TLV62569ADRL
SOT-563-40℃~+125℃@(TJ) 1 1.5MHz 2.5V~5.5V 2A 600mV~5.5V Adjustable Buck Built-in Overcurrent Protection Step-down type Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
W25Q128JVPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 120ms@(32KB) 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASH
FT2232HQ
QFN64Dual High Speed USB To Multipurpose UART/FIFO ICFTDIUncategorised
Parts
125| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 0.1u | Capacitor_SMD:C_0201_0603Metric | C11, C13, C14, C16, C19, C20, C21, C22, C24, C25, C27, C28, C29, C33, C47 |
| 15 | 0.1u | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C4, C7, C8, C9, C10, C17, C32, C35, C36, C37, C41, C42, C43, C44 |
| 12 | 4.7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R3, R4, R5, R8, R9, R20, R21, R31, R32, R33, R34 |
| 11 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12, C15, C18, C23, C26, C31, C48, C60, C62, C64, C65 |
| 5 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R27, R35, R36, R37, R42 |
| 5 | 120Ohm | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1, FB2, FB3, FB4, FB5 |
| 5 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R7, R28, R29, R30 |
| 4 | 470 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R16, R17, R18, R19 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12, R14, R41 |
| 3 | 2.2uH | Inductor_SMD:L_1210_3225Metric_Pad1.42x2.65mm_HandSolder | L1, L2, L3 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C59, C61, C63 |
| 3 | TLV62569ADRL | Package_TO_SOT_SMD:SOT-563 | U6, U7, U8 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5, C6 |
| 2 | 2.2k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R6, R38 |
| 2 | 22 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R22, R23 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R24, R25 |
| 2 | Conn_02x20_Odd_Even | Local:Molex_SlimStack_52991-0408_2x20_P0.50mm_Vertical | J1, J5 |
| 2 | GRN | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D3, D6 |
| 2 | RED | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D1, D5 |
| 1 | 12M | Passive_Robotech:FA-238V | Q2 |
| 1 | 12k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R26 |
| 1 | 15p | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3 |
| 1 | 2.49k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R43 |
| 1 | 200k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11 |
| 1 | 22u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 442k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R13 |
| 1 | 66.5k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R15 |
| 1 | 93LCxxC | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U10 |
| 1 | BLUE | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D4 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J4 |
| 1 | FT2232HQ | Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP4.35x4.35mm | U5 |
| 1 | LFD2NX-17-7MG121I | Local:LFD2NX-17-7MG121I | U1 |
| 1 | LOGO | LSM6DSV16XTR:RoboTech_Logo | G*** |
| 1 | Q_NMOS | Package_TO_SOT_SMD:SOT-416 | Q1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | SiT8008xx-7x-xxN | Oscillator:Oscillator_SMD_SiT_PQFN-4Pin_2.0x1.6mm | Y2 |
| 1 | TPSM53604RDA | Local:Texas_B3QFN-14-1EP_5x5.5mm_P0.65mm_ThermalVia | U9 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
| 1 | W25Q128JVP | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U3 |
| 1 | YEL | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D2 |
| 1 | ~ | Diode_Robotech:SOD-123 | D7 |
| 1 | ~ | Connector_Robotech:Molex_Nano-Fit_105309-xx02_1x02_P2.50mm_Vertical | CON1 |
Similar boards
- 2 layers100 × 90.8 mm
- 6 layers95 × 73 mm
- 4 layers68 × 43 mm
- 4 layers100 × 60 mm
- 4 layers50 × 30 mm
Picothermal hardware
icamaster/picothermal
Thermal camera based on Flir Lepton with RP2040 and USB-C
121 parts72MIT - 4 layers39.3 × 60.8 mm
- 4 layers55.5 × 70 mm
ESP32 LoRa Wireless Node
Balamanikandan-projects/ESP32-RFM95W-LoRa-Wireless-Telemetry-Node
A compact, high-performance, 4-layer custom PCB design integrating an ESP32-WROOM-32E microcontroller with an RFM95W sub-GHz LoRa radio module.
31 parts
Questions
How big is the CertusNX PCB?
It measures 40 × 40 mm and has 4 copper layers, 1.59 mm thick.
What parts does the CertusNX use?
125 parts, built around the LFD2NX-17-7MG121I, TPSM53604RDA, TLV62569ADRL and W25Q128JVPIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CertusNX KiCad files?
From the c4tsnest/certus_test repository on GitHub, at the commit this page was made from: the board is CertusNX.kicad_pcb and its schematic CertusNX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CertusNX design in my own project?
Its repository states no licence, so its author keeps all rights: ask c4tsnest before reusing the design.