Skip to the content
2 layers25.4 × 52.1 mmAtarimod, the printed circuit board in 3D

FPGA board to create a component video signal for vintage computers.

Size
25.4 × 52.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
67
Pads
135
Tracks, vias
387, 41
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
8 Oct 2017
Updated
6 Feb 2025

Overview

Atarimod is an open-source printed circuit board by c0pperdragon, from the c0pperdragon/A-VideoBoard repository on GitHub, published under the MIT licence. It is a 2-layer board of 25.4 × 52.1 mm with 14 parts on 67 nets, routed with 387 tracks and 41 vias.

It is built around the SN74LVC14ADBRE4 and MIC5504-3.3YM5. Its parts include 6 capacitors, 5 ICs, 2 connectors and 1 resistor. It belongs with the fPGA and programmable logic and retro computing and games boards of this library.

Main components

2

README

README.md

A-Video Board

A small FPGA board with a component video interface to directly drive an analog monitor or TV input. Its main purpose is to create component video / RGB mods of vintage home computers and consoles or to provide video output for hobby projects.

It consists of the purest minimum parts necessary to have a multi-purpose FPGA combined with a simple way to generate a YPbPr signal. After much research I finally settled on a cheap MAX 10 device in a TQFP-144 package which I can solder by hand (barely). The rest of the parts are pretty cheap and quite easy to solder.

To interface any of the vintage systems to the A-Video Board, level shifters are necessary to translate the 5 volt to 3.3 volt for the FPGA input pins. These level shifters can be implemented in a system specific daughter board that can be stacked on top of the A-Video board. Any such interface board can probably be implemented in a simple single-sided wide-pitch PCB that can be even home-etched with some experience.

Currently I have built applications of the A-Video board for

Images

alt text alt text

Board design

The board has these main parts

  • 10M02SCE144: fairly cheap FPGA of the MAX10 series
  • LM1117IMPX-3.3: linear voltage regulator
  • LFSPX0024957: 25Mhz clock generator
  • THS7316: video output amplifier
  • R1-R19: three 5-bit DACs made from transistors

and various supporting passive components, mainly decoupling, filtering and pull-ups.

It has the following connectors:

  • GPIO1 20-pin header that directly connects to FPGA pins
  • GPIO2 10-pin header with two pins providing GND and +3.3V, the remaining 8 connect to the FPGA.
  • JTAG 10-pin header for programming the FPGA (via an USB-Blaster or compatible device)
  • 3 RCA sockets to output the video signal (normally YPbPr, but other formats could be produced as well). Note that in the schematics these sockets are denoted as BNC, but are actually RCA connectors of type RCJ-046 (green), RCJ-042 (red), RCJ-045 (blue).
  • GND, VIN Provide between 4.5V and 9V as supply voltage. The board consumes about 80mA.

Contact

If you plan to use an A-Video board, feel free to contact me for assistance: reinhard.grafl (at) aon.at
Maybe I will either have some spare PCBs I could send you to populate yourself, or even provide you with a fully assembled board for the cost of the parts and shipping.

Parts

14
QtyValueFootprintReferences
4100nFCapacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolderC3, C4, C5, C6
4SN74LVC14ADBRPackage_SO:SSOP-14_5.3x6.2mm_P0.65mmIC1, IC2, IC3, IC4
210uFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC1, C2
1100Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR10
1CONN_02X10Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_VerticalP2
1DIP40_SocketProjectFootprints:socket_embedded_40pinP1
1MIC5504-3.3YM5Package_TO_SOT_SMD:SOT-23-5U2

More from c0pperdragon/A-VideoBoard

3
  • 2 layers43.2 × 53.3 mmA VideoBoard, the printed circuit board in 3D

    A VideoBoard

    c0pperdragon/A-VideoBoard

    FPGA board to create a component video signal for vintage computers.

    75 parts71MIT
  • 2 layers24.4 × 53.3 mmC64board, the printed circuit board in 3D

    C64board

    c0pperdragon/A-VideoBoard

    FPGA board to create a component video signal for vintage computers.

    12 parts71MIT
  • 2 layers47 × 19 mmZxspectrummod, the printed circuit board in 3D

    Zxspectrummod

    c0pperdragon/A-VideoBoard

    FPGA board to create a component video signal for vintage computers.

    8 parts71MIT

Similar boards

  • 4 layers89.7 × 82.9 mmICE40UP5K logic analyzer rev2, the printed circuit board in 3D

    ICE40UP5K logic analyzer rev2

    hack-a-tack/FPGA_Logic_Analyzer

    (Info applies to rev. 1, update for later revisions (only final rev. matters in the README)) FPGA-based 8-channel logic analyzer implemented on iCE40UP5K.

    170 parts
  • 2 layers172 × 152.9 mmTrackpad, the printed circuit board in 3D

    Trackpad

    george-norton/peacock

    A big QMK powered trackpad

    102 parts309CERN-OHL-S-2.0
  • 2 layers22.9 × 36.7 mmUsb2usb, the printed circuit board in 3D

    Usb2usb

    tmk/USB2USB_Converter

    USB to USB keyboard protocol converter supported by TMK keyboard firmware

    26 parts152
  • 2 layers78 × 130 mmLofence, the printed circuit board in 3D

    Lofence

    kiu/lofence

    LoFence is a LoRaWAN capable IoT electric fence monitoring system running on the The Things Network.

    65 parts142MIT
  • 2 layers96.5 × 55 mmVera module rev2, the printed circuit board in 3D

    Vera module rev2

    fvdhoef/vera-module

    Versatile Embedded Retro Adapter

    120 parts138MIT
  • 2 layers120 × 130 mmSingularitySurfer V1, the printed circuit board in 3D

    SingularitySurfer V1

    nkrackow/SingularitySurfer-FPGA-Lock-In-Amplifier

    Repository for the development of an FPGA based DSP Lock-In Amplifier

    174 parts80MIT
  • 4 layers60.2 × 20.8 mmPhaseLatchMini, the printed circuit board in 3D

    PhaseLatchMini

    AndersBNielsen/PhaseLatchMini

    High-rate continuous streaming of interleaved dual ADC (I/Q) samples over USB Full‑Speed (FS) using only the built‑in CDC class on an STM32F103C8 ("Blue Pill" style) board.

    63 parts72
  • 2 layers98 × 56 mmThermal pcb, the printed circuit board in 3D

    Thermal pcb

    Badbird5907/thermal-camera

    My design of a cheap and affordable thermal camera

    68 parts59MIT

Questions

How big is the Atarimod PCB?

It measures 25.4 × 52.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Atarimod use?

14 parts, built around the SN74LVC14ADBRE4 and MIC5504-3.3YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Atarimod KiCad files?

From the c0pperdragon/A-VideoBoard repository on GitHub, at the commit this page was made from: the board is atarimod/board/atarimod.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Atarimod design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).