Skip to the content
2 layers30 × 30 mmLight, the printed circuit board in 3D

Minuet upgrades your MAXXAIR Maxxfan with a brushless DC motor, home automation features, and accessories.

Size
30 × 30 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
24
Pads
108
Tracks, vias
117, 21
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
30 Dec 2024
Updated
11 Oct 2026

Overview

Light is an open-source printed circuit board by brown-studios, from the brown-studios/minuet repository on GitHub, published under the MIT licence. It is a 2-layer board of 30 × 30 mm with 24 parts on 24 nets, routed with 117 tracks and 21 vias.

It is built around the LP2985-50DBVR, SN74LVC1G17DBVR and B3B-XH-A, with the PH2-16-UA among its other parts. Its parts include 7 capacitors, 5 resistors, 4 connectors and 3 ICs. It belongs with the home automation and IoT and robots and motor control boards of this library.

Main components

4

README

README.md

Minuet fan controller

Minuet upgrades your MAXXAIR Maxxfan with a brushless DC motor, home automation features, and accessories.

Improve your quality of life in your campervan, RV, trailer, or truck!

  • Replace your fan's original motor with a quieter brushless motor. No more cleaning squeaky motor brushes!
  • Install Minuet with simple hand tools. You can revert back to the original equipment later if you want.
  • Connect your fan to your home automation system if you have one. Works with your original infrared remote control and wired wall controls too.
  • Install the light accessory to add a ring of lights to your fan for illumination and ambiance.
  • Install the cover sensor accessory to stop the fan and turn off the lights automatically when you attach an insulated vent cover.
  • Enjoy a more polished user experience with enhanced thermostat controls and less beeping.
  • Customize your fan as you like because the firmware and hardware are open source!
    • Expand the ESPHome-based firmware.
    • Connect off-the-shelf I2C environmental sensors and devices to the QWIIC port.
    • Make your own hardware accessories for the expansion port.
    • Share your work with the community!

This repository contains the Minuet documentation and hardware design files. You are welcome to modify the Minuet firmware and hardware subject to the license terms and we encourage you to make your own accessories. We welcome thoughtful contributions.

Refer to the Minuet firmware repository for source code.

Get to know Minuet

Watch Minuet in action and follow along with how it was made with these videos:

Project status

Minuet is in active development.

The latest prototype is feature complete, works well, and is being tested by a few volunteers.

Our next tasks are finalizing the design, working with manufacturers to fabricate kits with everything you will need to upgrade your Maxxfan, and planning for order fulfillment. We are also investigating the possibility of manufacturing custom brushless fan motors that will fit into the fan housing with fewer adapters. Please contact us if you would like to contribute your manufacturing experience to this project.

Watch this space for updates on our progress. We're thrilled by your interest in Minuet and we look forward to offering you a great upgrade for your Maxxfan!

See project history for the story of how we got here.

Author's note

Hey folks, I'm Jeff!

I started building my campervan in 2023 after some delightful adventures in New Zealand. Like many of you, I installed a Maxxfan in my campervan because it was the most popular fan for van builders. It worked well for a while but less than a year after I installed it, the fan started making some awful squeaking noises. I tried the usual advice: clean the motor brushes, replace the bearings, run the motor on high for a day, and nothing helped for long. I tried to ignore the problem.

When the winter rainy season arrived and interrupted my van build, I started the squeaking fan again. I had already started designing a circuit board to synchronize the Maxxfan with my home automation system and I found it tedious to work around the existing logic of the Maxxfan circuit board. It occurred to me that it might be easier to design my own controller from scratch... and then I could use a brushless fan motor and solve my fan squeaking problem too!

So here we are. I've made several prototypes, enjoyed the quiet, added quality of life features, made some friends, and learned a lot along the way. I'm satisfied with how Minuet has improved my comfort and I hope you'll like it too.

Getting started

Read these guides to learn how to build, install, and use Minuet and its accessories.

  1. Hardware guide: How to build Minuet hardware.
  2. Installation guide: How to install Minuet into your Maxxfan.
  3. User guide: How to use Minuet.

Good luck and enjoy your fan!

Compatibility

Minuet is anticipated to be compatible with the following Maxxfan models. Some models have yet to be specifically tested and are shown as unverified in the table.

Compatible modelLid typeLid colorTemperature sensorRain sensorInfrared receiverVerified
Maxxfan Deluxe 7500Krain coversmokeyesnoyesyes
Maxxfan Deluxe 7000Krain coverwhiteyesnoyesno
Maxxfan Deluxe 6200Krain coversmokeyesnono †no
Maxxfan Deluxe 5100Krain coverwhiteyesnono †no
Maxxfan Plus 4500K‡low profilesmokeyesyesyesyes

†: When you install Minuet in a Maxxfan whose keypad does not have a window for an infrared receiver, you will be unable to use Minuet's infrared remote control features. (It may be possible to replace or punch a hole through the keypad to make a window for the infrared receiver and use its features.)

‡: The Maxxfan Plus 4500K lid takes longer to open and close so the firmware must be modified to account for the extra duration as of Minuet v3.0. This difference will be resolved by improving end-of-travel detection.

Minuet is not compatible with the following Maxxfan models.

Incompatible modelsReason
Maxxfan Deluxe 5101K, 6201K, 7001K, 7501K, 8001K, 8501Kexhaust only keypad (no in/out button)
Maxxfan Deluxe 5301K, 6401K4 speed keypad (different buttons)
Maxxfan Plus 4000K, 4002K, 4050Kmanual lift
Maxxfan 4301K, 4401K, 4501Kmanual lift
Maxxfan Low Profile, Mini, Domedifferent electronics

Notice

The Minuet software, documentation, design, and all copyright protected artifacts are released under the terms of the MIT license.

The Minuet hardware is released under the terms of the CERN-OHL-W license.

Parts

24
QtyValueFootprintReferences
3100KResistor_SMD:R_0603_1608MetricR2, R4, R5
2100nCapacitor_SMD:C_0603_1608MetricC4, C6
210nCapacitor_SMD:C_0603_1608MetricC2, C7
2Conn_01x09Generic:Pins_1x09J3, J4
2JLCPCB_PCBA_Tooling_HoleGeneric:JLCPCB_PCBA_Tooling_HoleTH1, TH2
110uCapacitor_SMD:C_1210_3225MetricC5
11KResistor_SMD:R_0603_1608MetricR3
11uCapacitor_SMD:C_0805_2012MetricC1
12.2uCapacitor_SMD:C_0603_1608MetricC3
133Resistor_SMD:R_0603_1608MetricR1
1B3B-XH-AConnector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_VerticalJ2
1LP2985-50DBVRPackage_TO_SOT_SMD:SOT-23-5U1
1PH2-16-UAConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ1
1SN74LVC1G17DBVRPackage_TO_SOT_SMD:SOT-23-5U2
1SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP2
1SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP1
1TPS22810(-Q1)Package_TO_SOT_SMD:SOT-23-6U3
1Val**Generic:ProtoPinsPROTO

More from brown-studios/minuet

3
  • 4 layers79 × 79 mmMinuet, the printed circuit board in 3D

    Minuet

    brown-studios/minuet

    Minuet upgrades your MAXXAIR Maxxfan with a brushless DC motor, home automation features, and accessories.

    103 parts67MIT
  • 2 layers30 × 30 mmLight, the printed circuit board in 3D

    Light

    brown-studios/minuet

    Minuet upgrades your MAXXAIR Maxxfan with a brushless DC motor, home automation features, and accessories.

    21 parts67MIT
  • 4 layers25 × 25 mmEnvironment, the printed circuit board in 3D

    Environment

    brown-studios/minuet

    Minuet upgrades your MAXXAIR Maxxfan with a brushless DC motor, home automation features, and accessories.

    17 parts67MIT

Similar boards

  • 2 layers17.7 × 12.1 mmMicrobit 0.6, the printed circuit board in 3D

    Microbit 0.6

    StuckAtPrototype/MicroBit328

    The MicroBit328 is an ultra-compact Arduino-compatible development board measuring just 11mm × 16mm - small enough to fit on your fingertip.

    23 parts75
  • 4 layers195 × 45 mmBed lift, the printed circuit board in 3D

    Bed lift

    j9brown/bed-lift

    Motorized bed lift system

    154 parts2MIT
  • 4 layers66 × 71.5 mmEeg ads1299, the printed circuit board in 3D

    Eeg ads1299

    kaanpars/16_channels_eeg_card

    I designed cards both in INA333 + TLV4333 and ADS1299. It is up to you which analog or digital output you should want to get. Importing restrictions in Turkey dragged me to designing my own sensor cards. ENJOY!

    103 partsGPL-3.0
  • 2 layers178.2 × 110.9 mmLegRobotBoardTeensy, the printed circuit board in 3D

    LegRobotBoardTeensy

    01binary/str1ker

    A human-scale mech integrated with Robot Operating System

    179 parts20
  • 2 layers24 × 27.9 mmUartFEC, the printed circuit board in 3D

    UartFEC

    medo64/UartFEC

    Framework laptop expansion card exposing serial TTL interface

    20 parts13MIT
  • 4 layers50 × 80 mmARGOS DEMO, the printed circuit board in 3D

    ARGOS DEMO

    CNES/argos-demo-board

    Demo board designed to use the ARRIBADA SMD module via USB to send ARGOS messages to the Kineis constellation.

    91 parts7CERN-OHL-S-2.0
  • 10 layers30.6 × 65 mmEffectiveRangeHat simple, the printed circuit board in 3D

    EffectiveRangeHat simple

    EffectiveRange/pcb-mrhat

    PCB project for MrHAT RPi extension hat project

    117 parts2
  • 2 layers24 × 27.9 mmCanankaFEC, the printed circuit board in 3D

    CanankaFEC

    medo64/CanankaFEC

    CAN bus framework expansion card.

    28 parts2MIT

Questions

How big is the Light PCB?

It measures 30 × 30 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Light use?

24 parts, built around the LP2985-50DBVR, SN74LVC1G17DBVR, B3B-XH-A and PH2-16-UA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Light KiCad files?

From the brown-studios/minuet repository on GitHub, at the commit this page was made from: the board is hardware/light/v4/light.kicad_pcb and its schematic hardware/environment/v4/environment.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Light design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).