4 layers85 × 68 mm
4 layers145 × 73 mm
Dashboard
broncoracing/dashboardBR23 Dashboard PCB/Firmware
- Size
- 145 × 73 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 284
- Nets
- 252
- Pads
- 1,043
- Tracks, vias
- 1,848, 419
- Pours
- 19
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 28 Sep 2022
- Updated
- 26 Oct 2026
Overview
Dashboard is an open-source printed circuit board by broncoracing, from the broncoracing/dashboard repository on GitHub. It is a 4-layer board of 145 × 73 mm with 284 parts on 252 nets, routed with 1,848 tracks and 419 vias.
It is built around the STM32F103C8T6, 74HCT541D and SN65HVD230D, with the ADP2303ARDZ-5.0, ESD224DQAR and AMS1117-3.3 among its other parts. Its parts include 129 diodes, 102 capacitors, 10 ICs, 8 resistors and 4 connectors. It belongs with the STM32 boards of this library.
Main components
9
STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
74HCT541D
SO-20-40℃~+125℃ 1 15ns@4.5V,50pF 160uA 4.5V~5.5V 6mA 6mA 74HCT 8 Tri-State Unidirectional SO-20-300mil Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffers, Drivers, Receivers, Transceivers
SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversADP2303ARDZ-5.0
SOIC-8-EP-40℃~+125℃@(TJ) 1 3A 3V~20V 5V 700kHz Buck Buck Built-in Fixed No SOIC-8-EP DC-DC Converters ROHSAnalog DevicesDC-DC Converters
ESD224DQAR
USON-10(1x2.5)-40℃~+125℃ 0.5pF 100pA 14V 17W@8/20us 2A@8/20us 3.6V 7.9V Bidirectional ESD Four channels IEC 61000-4-2 USON-10(1x2.5) ESD and Surge Protection (TVS/ESD) ROHSTexas InstrumentsESD Protection Devices
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
SSB43L-E3
SMB(DO-214AA)-65℃~+150℃ 1 Independent 100A 30V 380mV@4A 4A 600uA@30V SMB(DO-214AA) Schottky Diodes ROHSVishay IntertechnologySchottky DiodesSMBJ15CA
DO-214AA(SMB)-65℃~+150℃ 15V 18.5V 1uA 24.4V 24.6A@10/1000us 600W@10/1000us Bidirectional TVS DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHSMDDESD And Surge Protection (TVS/ESD)
README
README.mdtemplate
Use this repo as the base for new repos. Follow directory structure below:
├── firmware
│ └── firmware project
└── pcb
├── PCB layout
├── schematic
└── etcUpon pushing a commit, a Github action will automatically run electrical & design rule checks to verify the pcb design, then generate gerber/drill/BOM files and renderings/PDFs of the pcb and schematics.
Parts
284| Qty | Value | Footprint | References |
|---|---|---|---|
| 90 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C10, C12, C13, C17, C18, C20, C21, C22, C23, C24, C25, C26, C27, C101 +74 |
| 90 | WS2812B | XL-3528RGBW-WS2812B:XL-3528RGBW-WS2812B | D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112, D113, D114, D115 +74 |
| 32 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D24, D25, D26 +16 |
| 10 | Jumper_2_Bridged | TestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | JP1, JP2, JP3, JP4, JP5, JP6, JP7, JP8, JP9, JP10 |
| 8 | 1k | Resistor_SMD:R_Array_Convex_4x0603 | RN14, RN15, RN17, RN18, RN20, RN21, RN23, RN24 |
| 4 | 10k | Resistor_SMD:R_Array_Convex_4x0603 | RN13, RN16, RN19, RN22 |
| 4 | 30p | Capacitor_SMD:C_0402_1005Metric | C14, C15, C16, C19 |
| 4 | ESD224DQA | Package_DFN_QFN:Diodes_UDFN-10_1.0x2.5mm_P0.5mm | U17, U18, U19, U20 |
| 4 | MountingHole | MountingHole:MountingHole_3.5mm_Pad | H1, H2, H3, H4 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C4, C5, C11 |
| 3 | SSB43L | Diode_SMD:D_SMB | D2, D128, D129 |
| 2 | 1.5k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 100k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C97, C100 |
| 2 | 4.7u | Inductor_SMD:L_7.3x7.3_H3.5 | L1, L2 |
| 2 | 47R | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 2 | 47u | Capacitor_SMD:C_0805_2012Metric | C99, C102 |
| 2 | 60 | Resistor_SMD:R_0805_2012Metric | R5, R6 |
| 2 | ADP2303ARDZ-5.0 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U2, U6 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D5, D6 |
| 2 | TC2030 | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J1, J3 |
| 1 | 100R@100MHz | Resistor_SMD:R_0805_2012Metric | FB1 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 74HCT541 | Package_SO:SSOP-20_4.4x6.5mm_P0.65mm | U3 |
| 1 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | D_TVS_Dual_AAC | Package_TO_SOT_SMD:SOT-323_SC-70 | D7 |
| 1 | Fuse | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | JST B04B-XASK | Connector_JST:JST_XA_B04B-XASK-1_1x04_P2.50mm_Vertical | J4 |
| 1 | JST B24B-PADSS-F | JST_B24B_PADSS:JST_B24B_PADSS | J2 |
| 1 | SMBJ15CA | Diode_SMD:D_SMB | D1 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U4 |
Questions
How big is the Dashboard PCB?
It measures 145 × 73 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Dashboard use?
284 parts, built around the STM32F103C8T6, 74HCT541D, SN65HVD230D and ADP2303ARDZ-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dashboard KiCad files?
From the broncoracing/dashboard repository on GitHub, at the commit this page was made from: the board is pcb/PCB.kicad_pcb and its schematic pcb/5v3A_reg.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dashboard design in my own project?
Its repository states no licence, so its author keeps all rights: ask broncoracing before reusing the design.
Similar boards
- 2 layers28 × 38 mm
ADP2303ARDZ
electronicSoup/SMPS-ADP2303ARDZ
This project is an attempt at an open hardware design Switched Mode Power Supply. It's based on the Analog Devices ADP2302/ADP2303 chips.
17 parts - 4 layers82.4 × 100 mm
- 2 layers
- 2 layers43.5 × 40.7 mm
Stm32
Prap04/STM32_POWER_CONTROLLER_BOARD_DESIGN-
This project involves the design and development of a custom STM32F103C8T6-based embedded control board integrating power management, sensor interfaces, and industrial communication protocols.
38 parts - 2 layers88.6 × 69.9 mm
ExpressionController
amonbenson/expad
A four-jack USB MIDI adapter for expression and sustain pedals, built on a Raspberry Pi Pico 2 W. It works out what is plugged into each jack - whichever contact a pedal's wiper is on, and whether it is a potentiometer…
147 partsMIT - 4 layers78.5 × 91 mm
- 2 layers106.7 × 78.4 mm
