

Hackathon board v2
KiCad 10 project. Board is 100 × 80 mm, four layers, fabricated by JLCPCB.
- Size
- 100 × 80 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 75
- Nets
- 89
- Pads
- 346
- Tracks, vias
- 709, 87
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 30 Aug 2026
- Updated
- 30 Aug 2026
Overview
Hackathon board v2 is an open-source printed circuit board by Brian-Nziza, from the Brian-Nziza/ESP32-Hackathon-Board repository on GitHub. It is a 4-layer board of 100 × 80 mm with 75 parts on 89 nets, routed with 709 tracks and 87 vias.
It is built around the CH340C, ESP32-WROOM-32 and MT3608, with the AMS1117-3.3, MPU-6050 and S8050 among its other parts. Its parts include 21 resistors, 15 capacitors, 11 connectors, 6 ICs and 5 diodes. It belongs with the ESP32 boards of this library.
Main components
6CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMT3608
SOT-23-6-40℃~+85℃ 1 1.2MHz 100uA、1.6mA 2A 2V~24V Adjustable Boost Boost Built-in No SOT-23-6 DC-DC Converters ROHS西安航天民芯DC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometersS8050
SOT-23-55℃~+150℃ 1 NPN 100MHz 100nA 120 25V 300mW 500mA 5V 600mV NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
README
Hardware/README.mdHardware
KiCad 10 project. Board is 100 × 80 mm, four layers, fabricated by JLCPCB.
Stackup
F.Cu signal
In1 GND plane
In2 +3.3V plane
B.Cu signalBoth planes are on the inner layers, so every signal on an outer layer has a solid reference directly beneath it and return current can follow the forward path instead of going the long way round.
It also means GND and +3.3V are barely routed as traces at all. Pads drop
straight down to their plane through a via, which is why the board has 85 vias
for 53 nets.
Power architecture
USB-C -> F1 PTC fuse -> MCP73833 charger -> Li-ion cell
|
v
MT3608 boost -> 5.1 V
|
v
AMS1117 LDO -> 3.3 VD5, a Schottky, ORs the USB rail with the boost output so the board runs from
either source.
This chain is about 55% efficient from cell to logic rail. The boost runs near 90%, but the LDO then discards (5.1 − 3.3) / 5.1 = 35% of everything that passes through it. A direct buck-boost to 3.3 V would reach roughly 90% overall and give about 1.6× the runtime. It is the first thing I would change.
Boost layout
The output loop — U5.1 → D1 → C5 → GND → U5.2 — is where the switching
current is discontinuous, so it's the one loop on the board whose geometry
matters. The switch node Net-(D1-A) spans 4.3 mm across all three of its pads
(U5.1, L1.1, D1.2), which keeps the radiating copper small.
C5's ground return runs 9.8 mm on the surface, which would be a problem on a
two-layer board. With a solid GND plane 0.2 mm below, the return current flows
directly under the forward path instead, provided there's a via at each end —
one within 1.4 mm of C5's ground pad and one near U5's.
The feedback trace Net-(U5-FB) is deliberately kept at 0.25 mm even though it
sits 4 mm from an 0.8 mm switching node. It's a high-impedance sense line;
making it wider would make it a better antenna, not a better conductor.
Netclasses
| Class | Width | Nets |
|---|---|---|
| High Current | 0.8 mm | +BATT, Net-(D1-A), GND |
| Power | 0.6 mm | +5V, Ext_5V, Net-(F1-Pad2), +3.3V |
| Default | 0.25 mm | everything else |
Net-(U5-FB) and Net-(U4-PROG) stay on Default deliberately — both are
high-impedance sense nodes where narrow is correct.
RF
The WROOM module overhangs the top board edge so its antenna sits off the PCB, with a copper keepout drawn over the region. Copper under a chip antenna detunes it.
Routing
709 segments, 85 vias, 4 zones
53/53 nets complete
0 same-layer crossings between different nets
0 off-angle segments
36 right-angle corners of 564 (6.4%)
median detour 1.14x over the straight-line minimumConventions held throughout: 45° only, F.Cu horizontal and B.Cu vertical, and one spacing pitch — 1.0 mm — for parallel runs, so bundles read as groups rather than as individual traces that happen to be near each other.
The GPIO breakout is the clearest example: six traces at exactly 1.0 mm pitch running 45 mm down the left side of the board.
Connectors
| J1 | USB-C, power and UART |
| J2 | JST-PH, Li-ion cell |
| J3, J5 | SDA, SCL |
| J4, J6 | 3.3 V, GND |
| J7 | HC-SR04 — 5 V, TRIG, ECHO, GND |
| J8 | 2.8" ILI9341 display, 14-pin socket |
| J9, J10 | 5 V out, PWM |
| J11 | GPIO breakout — IO2, IO12, IO13, IO14, IO15, IO22 |
J11 exposes three strapping pins (IO2, IO12, IO15). IO12 in particular can prevent the chip from booting if it's held at the wrong level at reset — worth knowing before hanging anything off that header.
Parts
75| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_0805_2012Metric | R4, R7, R8, R11, R14, R19 |
| 4 | 100n | Capacitor_SMD:C_0805_2012Metric | C6, C9, C10, C14 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C1, C4, C7 |
| 3 | 1K | Resistor_SMD:R_0805_2012Metric | R1, R6, R18 |
| 3 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4 |
| 3 | S8050 | Package_TO_SOT_THT:TO-92_Inline | Q2, Q3, Q4 |
| 2 | 100k | Resistor_SMD:R_0805_2012Metric | R9, R20 |
| 2 | 4.7k | Resistor_SMD:R_0805_2012Metric | R15, R17 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | D_Schottky | Diode_SMD:D_SMA | D1, D5 |
| 2 | SW_Omron_B3FS | Button_Switch_SMD:SW_SPST_Omron_B3FS-100xP | SW3, SW4 |
| 1 | +5V | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | +BATT | TestPoint:TestPoint_Pad_D1.5mm | +BATT |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric | R21 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C15 |
| 1 | 100nf | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R13 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R12 |
| 1 | 2.2nf | Capacitor_SMD:C_0805_2012Metric | C12 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 22uf | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 2K | Resistor_SMD:R_0805_2012Metric | R16 |
| 1 | 2k | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | 3.3V | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 4.7uf | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 5V i2c | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | 5V_OUTPUT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | 75k | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | BATT_INPUT | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U3 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U2 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | GPIO pins | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | ILI 9341 2.8" | Connector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_Vertical | J8 |
| 1 | L | Inductor_SMD:L_Sunlord_SWPA4030S | L1 |
| 1 | MCP73833-xxx-MF | Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.58x2.35mm | U4 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U6 |
| 1 | MT3608 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | PTC | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | PWM | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | SCL | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | SDA | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_CK_JS102011SAQN | SW1 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | EXT 5V |
| 1 | USB_C_Receptacle_USB2.0_14P | personal_library:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | ~ | Package_TO_SOT_SMD:SOT-23 | XC61CN1 |
Similar boards
- 2 layers49.4 × 95.7 mm

- 2 layers43.3 × 62.9 mm

- 2 layers50 × 145 mm

SmartRemote
Circuit-Digest/Smart-Universal-Remote-with-Learning-function-and-Google-Assistant-Support
Smart Universal Remote with Learning function and Google Assistant Support
75 parts3 - 2 layers65 × 38.2 mm

Gps tracer
OlegDemk/ESP32_GPS_loger_v1
GPS logger can log in GPS data every 5 seconds into Micro SD card.
88 parts - 2 layers151 × 118 mm

- 2 layers85 × 56 mm

- 2 layers35 × 45 mm

LVGLDevKit
jppang/ESP32_MicroPython_LVGL_ST7789
Try to build an ESP32 firmware with LVGL and ST7789 drivers inside.
40 parts2 - 2 layers80 × 45 mm

Kizami
hasky00/kizami-core
FPGA side of Kizami — cycle-exact timecode + audio witness on iCE40
36 partsMIT
Questions
How big is the Hackathon board v2 PCB?
It measures 100 × 80 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Hackathon board v2 use?
75 parts, built around the CH340C, ESP32-WROOM-32, MT3608 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hackathon board v2 KiCad files?
From the Brian-Nziza/ESP32-Hackathon-Board repository on GitHub, at the commit this page was made from: the board is Hardware/hackathon_board_v2.kicad_pcb and its schematic Hardware/hackathon_board_v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hackathon board v2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Brian-Nziza before reusing the design.