

ODAmain ver2.0
circuit
- Size
- 100 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 85
- Nets
- 114
- Pads
- 373
- Tracks, vias
- 472, 154
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 11 Jul 2024
- Updated
- 27 Mar 2025
Overview
ODAmain ver2.0 is an open-source printed circuit board by boiled-mackerel, from the boiled-mackerel/NHK2024 repository on GitHub. It is a 2-layer board of 100 × 50 mm with 85 parts on 114 nets, routed with 472 tracks and 154 vias.
It is built around the STM32F446RET6, TJA1441AT/0Z and BD7LS04G-CTL, with the BNO055, NJM2845DL1-33-TE1 and 2SC3265-Y among its other parts. Its parts include 22 resistors, 14 capacitors, 14 ICs, 12 connectors and 10 diodes. It belongs with the STM32 boards of this library.
Main components
6STM32F446RET6
LQFP-64(10x10)-40℃~+85℃ 1.7V~3.6V 128KB 12bit 12bit 180MHz 32 Bit 50 512KB ARM Cortex-M4 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)TJA1441AT/0Z
SO-8-40℃~+150℃ 4.5V~5.5V 5Mbps 60mA CAN Transceiver SO-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversBD7LS04G-CTL
SSOP-5-40℃~+125℃ 1 1.65V~5.5V 10ns@5V,50pF 10uA 32mA 32mA SSOP-5 Inverters ROHSROHM SemiconductorInvertersBNO055
LGA-28(3.8x5.2)-40℃~+85℃ 2.4V~3.6V 40uA I2C、UART IMU X,Y,Z X,Y,Z ±16g ±2000dps LGA-28(3.8x5.2) Accelerometers ROHSBosch SensortecAccelerometersNJM2845DL1-33-TE1
TO-252-40℃~+85℃@(Ta) 1 14V 180mV@(500mA) 3.3V 400uA 45uVrms 75dB@(1kHz) 800mA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSNisshinbo Micro Devices Inc.Voltage Regulators - Linear, Low Drop Out (LDO) Regulators2SC3265-Y
SOT-23SOT-23 Bipolar (BJT) ROHSYFWBipolar (BJT)
Parts
85| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 1.5k | Footprint_nishi:R_0603_1608 | R5, R6, R7, R8, R9, R10, R11, R13, R16, R17, R18, R19 |
| 7 | 0.1u | Footprint_nishi:C_0805_2012 | C3, C6, C10, C11, C12, C13, C14 |
| 7 | 10k | Footprint_nishi:R_0603_1608 | R12, R14, R20, R21, R22, R23, R24 |
| 3 | 2.2u | Footprint_nishi:C_0805_2012 | C2, C8, C9 |
| 2 | 120 | Footprint_nishi:R_0603_1608 | R2, R3 |
| 2 | 20p | Footprint_nishi:C_0805_2012 | C4, C5 |
| 2 | 2SC3265-Y | NagaokaFootprint2023:2sc3265_SC-59_Handsoldering | Q1, Q2 |
| 2 | TJA1441AT | Footprint_nishi:SOIC-8_IR2302_TJA1441AT | U2, U3 |
| 1 | +3.3V | Footprint_nishi:LED_0603_1608 | D8 |
| 1 | +5V | Footprint_nishi:LED_0603_1608 | D7 |
| 1 | 0.33u | Footprint_nishi:C_0805_2012 | C1 |
| 1 | 4.7k | Footprint_nishi:R_0603_1608 | R15 |
| 1 | 4.7u | Footprint_nishi:C_0805_2012 | C7 |
| 1 | 8MHz | Footprint_nishi:crystal_hc-49u | Y1 |
| 1 | BD7LS04G-CTL | BD7LS04G-CTL:SOT95P280X125-5N | IC1 |
| 1 | BNO055 | watanabe_smy:BNO055 | U7 |
| 1 | BUSY | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D9 |
| 1 | CAN_1 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | CAN_2 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5 |
| 1 | D_Schottky | Footprint_nishi:smd_diode_SOD-323_HandSoldering_cus10f30 | U1 |
| 1 | EMC | Connector_JST:JST_XA_S02B-XASK-1_1x02_P2.50mm_Horizontal | J1 |
| 1 | FEP-02 | NagaokaFootprint2023:FEP-02_PIN_SOCKET | U8 |
| 1 | IM920sL | watanabe_smy:IM920sL | U9 |
| 1 | LOGO | watanabe_smy:sabamiso_10^10 | G*** |
| 1 | LOGO | Footprint_Monkey:RoboticsClub_logo_small | G*** |
| 1 | NJM2845DL1-33 | Footprint_nishi:NJM2845DL1-33 | U6 |
| 1 | PA4 | Footprint_nishi:LED_0603_1608 | D6 |
| 1 | PA5 | Footprint_nishi:LED_0603_1608 | D5 |
| 1 | PA6 | Footprint_nishi:LED_0603_1608 | D4 |
| 1 | PA7 | Footprint_nishi:LED_0603_1608 | D3 |
| 1 | R3006SB | watanabe_smy:R3006SB | U12 |
| 1 | REG | Footprint_nishi:tact_sw_smd_skrpabe10 | U11 |
| 1 | RESET | Footprint_nishi:tact_sw_smd_skrpabe10 | U10 |
| 1 | RX==RX | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | J11 |
| 1 | RX==TX | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | J9 |
| 1 | SLEEP | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D11 |
| 1 | ST-LINK | Connector_JST:JST_GH_BM06B-GHS-TBT_1x06-1MP_P1.25mm_Vertical | U5 |
| 1 | STATUS | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D12 |
| 1 | SW1:PC1 | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | SW2:PC2 | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | SW3:PC3 | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | SW4:PB12 | Button_Switch_THT:SW_PUSH_6mm | SW4 |
| 1 | TX==RX | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | J10 |
| 1 | TX==TX | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | J12 |
| 1 | Terminate_CAN1 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J2 |
| 1 | Terminate_CAN2 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J3 |
| 1 | XMIT | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D10 |
| 1 | gh:CAN_1 | Connector_JST:JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J6 |
| 1 | gh:CAN_2 | Connector_JST:JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J7 |
| 1 | im920sl_USB | Connector_USBver1.0:USB_A_CONNFLY_DS1095-WNR0 | J8 |
| 1 | power | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | U4 |
| 1 | stm32_f446re | Package_QFP:LQFP-64_10x10mm_P0.5mm | U13 |
The 81 most common of 85 parts.
More from boiled-mackerel/NHK2024
12- 2 layers50 × 50 mm

- 2 layers100 × 50 mm

- 2 layers50 × 50 mm

- 2 layers100 × 66 mm

- 2 layers91 × 55 mm

- 2 layers41.5 × 33.5 mm

- 2 layers77 × 67 mm

- 2 layers125 × 77.5 mm

- 2 layers50 × 25 mm

- 2 layers77 × 70 mm

- 2 layers57 × 64 mm

- 2 layers35 × 30 mm

Similar boards
- 2 layers100 × 100 mm

- 2 layers38.1 × 220.3 mm

- 2 layers50 × 100 mm

Parrot imu
LucienMorey/parrot_imu
This design will host an IMU board for the Parody tripedal robotic platform. It will expose connect an IMU to the teensy 4.1 microcontroller with the ability to deliver this data over CAN bus and over an ethernet…
29 parts3MIT - 2 layers80 × 60 mm

- 2 layers95 × 40.5 mm

Esp32tester
Lathe-Mariel/CAN
回路 | 部品(Item) | 説明 | 数量(Qauntity) | Akizukiコード ---|---|---|---|--- U1 | ESP32-DevKitC | ESP32マイコン・ボード| 1 | 115673 IC1 | TJA1441AT | CANトランシーバ| 1 | 117464 R1, R2 | 60.4Ω 1608 | 終端抵抗 | 2 | R3, R4 | 120Ω 1608 | LED電流制限抵抗 |…
20 parts1 - 2 layers79.2 × 99.9 mm

- 2 layers50 × 50 mm

- 2 layers60 × 45 mm

Questions
How big is the ODAmain ver2.0 PCB?
It measures 100 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ODAmain ver2.0 use?
85 parts, built around the STM32F446RET6, TJA1441AT/0Z, BD7LS04G-CTL and BNO055. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ODAmain ver2.0 KiCad files?
From the boiled-mackerel/NHK2024 repository on GitHub, at the commit this page was made from: the board is ODAmain/ODAmain_ver2.0/ODAmain_ver2.0.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ODAmain ver2.0 design in my own project?
Its repository states no licence, so its author keeps all rights: ask boiled-mackerel before reusing the design.