

Esp32tester
回路 | 部品(Item) | 説明 | 数量(Qauntity) | Akizukiコード ---|---|---|---|--- U1 | ESP32-DevKitC | ESP32マイコン・ボード| 1 | 115673 IC1 | TJA1441AT | CANトランシーバ| 1 | 117464 R1, R2 | 60.4Ω 1608 | 終端抵抗 | 2 | R3, R4 | 120Ω 1608 | LED電流制限抵抗 |…
- Size
- 95 × 40.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 20
- Nets
- 65
- Pads
- 147
- Tracks, vias
- 199, 10
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 6 Mar 2024
- Updated
- 7 Nov 2026
Overview
Esp32tester is an open-source printed circuit board by Lathe-Mariel, from the Lathe-Mariel/CAN repository on GitHub. It is a 2-layer board of 95 × 40.5 mm with 20 parts on 65 nets, routed with 199 tracks and 10 vias.
It is built around the ESP32-DEVKITC-VE, TJA1441AT/0Z and SDCW3216-2-222TF, with the SM24CANB-02HTG among its other parts. Its parts include 6 connectors, 4 capacitors, 4 resistors, 2 ICs and 1 diode. It belongs with the ESP32 boards of this library.
Main components
4ESP32-DEVKITC-VE
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesTJA1441AT/0Z
SO-8-40℃~+150℃ 4.5V~5.5V 5Mbps 60mA CAN Transceiver SO-8 CAN Transceivers ROHSNXP SemiconductorsCAN TransceiversSDCW3216-2-222TF
SMD-4P,3.2x1.6mm-40℃~+85℃ 1.2Ω 2 2.2kΩ@100MHz 200mA 50V SMD-4P,3.2x1.6mm Common Mode Filters ROHSSunlordCommon Mode FiltersSM24CANB-02HTG
SOT-23100nA 10A@8/20us 24V 26.7V 30pF 500W@8/20us 50V IEC 61000-4-2、IEC 61000-4-5 TVS SOT-23 ESD and Surge Protection (TVS/ESD) ROHSLittelfuseESD And Surge Protection (TVS/ESD)
README
Readme.mdKiCADで作ったPCBデータです.
CANバスをチェックするためのアナライザをESP32-DevKitCとTJA1441AT(NXP)で作ります.
CANバスとは,RJ45で接続します.中心寄りの2芯を使っています.
RJ45を2個搭載できるようになっているので,数珠つなぎにできます.従ってこのまま,センサノードとして利用しやすくなっています.
ESP32_DevKitCの全ピンが引き出されており,重ねる基板を作りやすくなっています.

BoM
網羅はできていませんが,だいたいこんなものがあればよいのではないでしょうか.
| 回路 | 部品(Item) | 説明 | 数量(Qauntity) | Akizukiコード |
|---|---|---|---|---|
| U1 | ESP32-DevKitC | ESP32マイコン・ボード | 1 | 115673 |
| IC1 | TJA1441AT | CANトランシーバ | 1 | 117464 |
| R1, R2 | 60.4Ω 1608 | 終端抵抗 | 2 | |
| R3, R4 | 120Ω 1608 | LED電流制限抵抗 | 4 | |
| C1 | 0.0047uF 1608 | 終端抵抗スプリッタ | 1 | 114552 |
| C2, C3 | 0.1uF 1608 | パスコン | 2 | 113374 |
| C4 | 1uF 1608 | パスコン | 1 | |
| J5 | 端子台 | 電源供給用(OPTION) | 1 | 101306 |
| L1 | SDCW3216-2-222TF | コモンモードチョークコイル | 1 | 110382 |
| D1 | SM24CANB-02HTG | TVS | 1 | (秋月電子取扱無し) |
| J3, J4 | ピンヘッダ 1x2 | 終端抵抗選択用 | 2 | |
| J1, J2 | Amphenol_RJHSE538X | RJ45ジャック(CANバス接続用) | 2 | |
| J6 | ピンヘッダ 1x2 | 拡張用ピンヘッダ(OPTION) | 1 |
※RJ45ジャックはいろいろな形状のものが流通しているので注意
※コモンモードチョークコイル,TVSは無くても動く
Schematics

使用例

Parts
20| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | C | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4 |
| 4 | R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4 |
| 3 | Conn_01x02_Pin | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J3, J4, J6 |
| 2 | RJ45_LED_Shielded | Connector_RJ:RJ45_Amphenol_RJHSE538X | J1, J2 |
| 1 | ESP32-DevKitC | PCM_Espressif:ESP32-DevKitC | U1 |
| 1 | SDCW3216-2-222TF | footprints:SDCW32162222TF | L1 |
| 1 | SM24CANB-02HTG | footprints:SM24CANB02HTG | D1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_RND:TerminalBlock_RND_205-00045_1x02_P5.00mm_Horizontal | J5 |
| 1 | TJA1441AT | footprints:SOIC127P600X175-8N | IC1 |
The 18 most common of 20 parts.
Similar boards
- 2 layers79.2 × 99.9 mm

- 2 layers37.3 × 20.6 mm

- 2 layers99.8 × 99.9 mm

Baseboard
Lathe-Mariel/PCB_PY32E407START_baseboard
型式 | 数量 | アイテム ---|---|--- FH-2x25SG(10) | 2 | 2.54連結ピンソケット PH-2x5SG | 1 | 2.54ピンヘッダ FH-2x2SG | 2 | 2.54ピンソケット DTS-63-N-V-BLK | 1 | タクトスイッチ | 6 | Pmodソケット OSR50603C1E | 4 | SMD LED RC0603J220R | 4 | SMD 1608 220Ω…
91 partsMIT - 2 layers50.8 × 68.6 mm

MCU Board
caipiblack/STM32-CAN-Bus-board
This is an STM32F042K6T6 based board that can be used to build sensors that communicate over a CAN bus
26 parts5GPL-3.0 - 4 layers40 × 26.5 mm

StandardModuleV2
ilicmiljan/open-can-controller
Open-source CAN bus controller for BMW E9X instrument clusters (Firmware + PCB)
41 parts5GPL-3.0 - 2 layers170.6 × 121.1 mm

- 2 layers125 × 78.2 mm

RC ESP32 V2
Poent/RC-Snowblower
Working on designing the impeller and auger portion of the snowblower. Switched from using a worm gear assembly to a custom ring and pinion setup using a spiral bevel gear.
84 parts2 - 4 layers84.5 × 64 mm

MESC brain board
owhite/balancing-robot-notes
A control theory and software development repo for a balancing robot.
59 partsMIT
Questions
How big is the Esp32tester PCB?
It measures 95 × 40.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32tester use?
20 parts, built around the ESP32-DEVKITC-VE, TJA1441AT/0Z, SDCW3216-2-222TF and SM24CANB-02HTG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32tester KiCad files?
From the Lathe-Mariel/CAN repository on GitHub, at the commit this page was made from: the board is esp32tester.kicad_pcb and its schematic esp32tester.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32tester design in my own project?
Its repository states no licence, so its author keeps all rights: ask Lathe-Mariel before reusing the design.