

Ws 3.0
A collection of mysensors nodes, gateways and HW from my home
- Size
- 72.7 × 114 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 53
- Pads
- 197
- Tracks, vias
- 572, 82
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 28 Dec 2018
- Updated
- 16 Apr 2025
Overview
Ws 3.0 is an open-source printed circuit board by boanjo, from the boanjo/myhome repository on GitHub. It is a 2-layer board of 72.7 × 114 mm with 57 parts on 53 nets, routed with 572 tracks and 82 vias.
It is built around the ATMEGA328P-AU, ATTINY85V-10SU and RFM95W-868S2, with the CR2032, 1N5819WS and ISS55EP06LMXTSA1 among its other parts. Its parts include 14 resistors, 12 capacitors, 7 connectors, 5 ICs and 4 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
6ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)ATTINY85V-10SU
SOIC-8-208mil-40℃~+85℃ 1.8V~5.5V 10MHz 10bit 512Byte 512Byte 6 8 Bit 8KB AVR Built-in FLASH SOIC-8-208mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)RFM95W-868S2
16-SMD16-SMD New Arrivals ROHSHopeRF Micro-electronicsUncategorisedCR2032
-- Unclassified goods ROHSMaxellUncategorised1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesISS55EP06LMXTSA1
SOT-23-3-5-55℃~+150℃ 1 P-Channel 1.2pF 180mA 18pF 2V 3.4pF 400mW 590pC@10V 60V 7Ω@4.5V P-Channel ±20V SOT-23-3-5 MOSFETs ROHSInfineon TechnologiesMOSFETs
README
README.mdmyhome
A collection of mysensors nodes, gateways and HW from my home
I use a mix of NRF (2.4GHz) and RFM69 (433MHz) depending on the usage of the sensor. For longer distances i use RFM69 but they are a bit more power hungry so they all fill a purpose
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C10, C11, C12, C15, C16 |
| 6 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3, R4, R6, R9, R11 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | MH1, MH2, MH3, MH4 |
| 2 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R14 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13, C14 |
| 2 | 560k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15, R16 |
| 2 | CR2032 | boan_devices:CR2032 standing 1074 | BT1, BT2 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C8 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 12V | Connector_Pin:Pin_D1.0mm_L10.0mm | TP1 |
| 1 | 1N5819WS | boan_devices:1N5819HW | D3 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 2.2uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C2 |
| 1 | 2604-1102 | boan_devices:wago 26041102 | J5 |
| 1 | 2k2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | 3.3V | Connector_Pin:Pin_D1.0mm_L10.0mm | TP2 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | ATtiny85V-10S | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |
| 1 | Antenna | boan_devices:Antenna 868MHz | AE1 |
| 1 | BAP70 | boan_devices:BAP70 | D2 |
| 1 | BLUE | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | Crystal | boan_devices:Crystal SMD FOXSDLF08020 | Y1 |
| 1 | FTDI MEGA | boan_devices:FTDI 6p | J7 |
| 1 | GND | Connector_Pin:Pin_D1.0mm_L10.0mm | TP3 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | ISP MEGA | boan_devices:AVR ISP 6p | J6 |
| 1 | ISP TINY | boan_devices:AVR ISP 6p | J1 |
| 1 | ISS55EP06LMXTSA1 | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q1 |
| 1 | LF33_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U2 |
| 1 | RESET ATMEGA | boan_devices:tactile smd 13019319 | SW3 |
| 1 | RESET TINY | boan_devices:tactile smd 13019319 | SW2 |
| 1 | RFM95W-868S2 | boan_devices:HOPERF_RFM9XW_SMD | U5 |
| 1 | Rain | boan_devices:RJ10 Horizontal | J2 |
| 1 | SW_DIP_x04 | Button_Switch_THT:SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW1 |
| 1 | Temp | boan_devices:RJ10 Horizontal | J4 |
| 1 | Wind | boan_devices:RJ10 Horizontal | J3 |
| 1 | XC6206PxxxMR | boan_devices:SOT-23 | U4 |
More from boanjo/myhome
2- 2 layers45.4 × 89.9 mm

- 2 layers92 × 82.3 mm

Similar boards
- 2 layers75 × 44 mm

Iot aio
RWTH-EBC/OSIGBApp
Open-Source Internet of Things (IoT) Gateways for Building Automation Applications
46 parts3MIT - 4 layers20 × 52 mm

IoT AIO
N5GEH/n5geh.devices.iot_wa_aio
IoT-AIO is a wireless adapter for developing IoT applications for Industrial and Building Automation Systems based on the Espressif chipset ESP32.
58 parts1MIT - 2 layers93 × 61 mm

- 2 layers50 × 50 mm

2025-Mouse
ChristmasOrnaments/2025-Mouse
The thirteenth in my series of Christmas ornaments
24 partsGPL-3.0 - 2 layers145 × 80 mm

Vallpass03
GustavoVieira13/vallpass
Electronic prototype of a lamp post using LoRa in the Smart Cities scope consisting of a PCB and firmware development.
46 parts - 2 layers45 × 53 mm

LoRa Node
cernohorsky/LoRa-Node
Simple LoRa Node based on Arduino Pro mini with RFM95W module and PCB antenna.
35 parts66 - 2 layers72 × 27 mm

- 2 layers43 × 93 mm

LoRaNode
cernohorsky/LoRa-Node-Solar
LoRa Node based on Arduino Pro mini with RFM95W module and PCB antenna. Includes TPS63031 buck-boost convertor and MCP7381 LiPo charger prepared for solar panel. PCB has I2C pinheader and few GPIO pads.
59 parts3
Questions
How big is the Ws 3.0 PCB?
It measures 72.7 × 114 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ws 3.0 use?
57 parts, built around the ATMEGA328P-AU, ATTINY85V-10SU, RFM95W-868S2 and CR2032. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ws 3.0 KiCad files?
From the boanjo/myhome repository on GitHub, at the commit this page was made from: the board is ws3.0/KiCad/ws_3.0/ws_3.0.kicad_pcb and its schematic postman_rfm95/KiCad/postman/postman.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ws 3.0 design in my own project?
Its repository states no licence, so its author keeps all rights: ask boanjo before reusing the design.