4 layers26.3 × 33.4 mm
Zigbee
blkburn/cc2652_zigbee_zed
Hardware/Software for a complete Zigbee-End-Device based on the CC2652
31 parts3MIT
4 layers49.6 × 32.1 mm
Daughter board
blkburn/cc2652_zigbee_zed3Hardware/Software for a complete Zigbee-End-Device based on the CC2652
- Size
- 49.6 × 32.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 32
- Nets
- 34
- Pads
- 139
- Tracks, vias
- 216, 44
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 19 Mar 2021
- Updated
- 29 Mar 2021
Overview
Daughter board is an open-source printed circuit board by blkburn, from the blkburn/cc2652_zigbee_zed repository on GitHub, published under the MIT licence. It is a 4-layer board of 49.6 × 32.1 mm with 32 parts on 34 nets, routed with 216 tracks and 44 vias.
It is built around the MX25R8035FM1IH1 and BAT-HLD-001. Its parts include 9 resistors, 5 capacitors, 5 diodes, 3 connectors and 2 ICs. It belongs with the radio and wireless boards of this library.
Main components
2
MX25R8035FM1IH1
SOP-8-40℃~+85℃ 1.65V~3.6V 100,000 cycles 108MHz 20 Years 3.6ms 8Mbit Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOP-8 NOR FLASH ROHSMXICNOR FLASH
BAT-HLD-001
SMDSMD Button And Strip Battery Connector ROHSTE ConnectivityButton And Strip Battery Connector
README
README.mdZigbee End Device based on the CC2652R1
This is the complete hardware and software design of a zigbee end device (ZED) designed to be run from a same CR2032 button cell battery.
Texas Instruments Code Composer and the Simplelink SDK is used for development; based on the zed_temperaturesensor_CC26X2R1_LAUNCHXL_tirtos_ccs project.
The hardware design replicates the Launchpad-CC26x2R1 development board as much as possible.
The CC2652R1 is an ultra-low power ARM Cortex process with support for a number of wireless protocols, such as; Thread, Zigbee®, Bluetooth® 5.1 Low Energy, IEEE 802.15.4, IPv6-enabled (6LoWPAN), as well as proprietary protocols including TI 15.4-Stack (2.4 GHz), and simultaneous multi-protocol operation via Dynamic Multiprotocol Manager (DMM).
Development baord power consuption is in line with published datasheet power comsumption figures, allowing the zigbee end device to last many months or years on a single CR2032 battery.
The development board can interface various I2C sensors; a pin breakout is provided to interface the many cheap sensors available on-line. An Adafruit 4-pin STEMMA connector is also provide to connect to an I2C device in their range.
A JTAG header is provided to interface XDS110 (or better) debuggers. A CC1352 Launchpad with built-in XDS110 has been used to debug the development boards.
4-pin bootloader
Master branch is currently built with:
- CCStudio version: 10.1.1.00004
- Simplelink_cc13x2_26x2_sdk_4_30_00_54
Parts
32| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C6 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R8, R9 |
| 3 | 150 | Resistor_SMD:R_0805_2012Metric | R5, R6, R7 |
| 3 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | AHT10, APDS9930, J1 |
| 3 | LED | daughter_board:Lite-On-LTST-S220KRKT-0-0-0 | D1, D2, D3 |
| 2 | 100 | Resistor_SMD:R_0805_2012Metric | R2, R4 |
| 2 | DIODE | daughter_board:SOD-123FL | D4, D5 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 2.2k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | BAT-HLD-001 | daughter_board:Linx-BAT-HLD-001-0 | BT1 |
| 1 | BLM18HE152SN1D | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | FB1 |
| 1 | CC2652 | daughter_board:rf_star_cc2652 | U3 |
| 1 | Conn_02x02_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J2 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J3 |
| 1 | Conn_02x06 | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J5 |
| 1 | EVQ-P7A01P | daughter_board:Panasonic-EVQ-P7A01P-0-0-MFG | SW2 |
| 1 | EVQ-P7A01P-switch2 | daughter_board:Panasonic-EVQ-P7A01P-0-0-MFG | SW1 |
| 1 | MX25R8035FM1IH1 | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | STEMMA_I2C_QT | Connector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | STEMMA1 |
More from blkburn/cc2652_zigbee_zed
1Similar boards
- 2 layers83.5 × 66 mm
Open ed Rev.B
krikzz/open-ed
Open-ED is a very simple and cheap open source Genesis/Megadrive cartridge. The cartridge does not have its own processor or FPGA, it is built in the old school style using only memory and discrete logic.
82 parts169MIT - 2 layers36 × 33 mm
Nrf52-sensor tag
HomeSmartMesh/nrf52_thread_sensortag
nRF52840 small sensor Tag, Low power design, battery operated
23 parts41MIT - 2 layers26.1 × 19.3 mm
Baken
RedBulletTooling/NRF9160-Tracker
This is hardware project concept of a CR2032 Operated small size LTE-M/NB-Iot GPS tracker
37 parts15 - 2 layers36 × 29.3 mm
Ble mvp 1b rev0
saewoonam/ble_adv_covid
Repo to implement the advertise and scanner portion for bluetooth to enable encounter/exposure tracing (e.g. Apple/Google / TCN / etc...) on a nRF52840 based battery powered dongle/device
71 parts10 - 2 layers33 × 99.1 mm
Soilmoisture
bahildebrand/soil-moisture-pcb
Capacitive soil moisture sensor routed in KiCad
9 parts8GPL-3.0 - 2 layers47.2 × 35 mm
- 4 layers50.8 × 53.3 mm
- 2 layers61.7 × 46.7 mm
Questions
How big is the Daughter board PCB?
It measures 49.6 × 32.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Daughter board use?
32 parts, built around the MX25R8035FM1IH1 and BAT-HLD-001. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Daughter board KiCad files?
From the blkburn/cc2652_zigbee_zed repository on GitHub, at the commit this page was made from: the board is hardware/cc2652_rf_star/daughter_board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Daughter board design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).