Skip to the content
6 layers150 × 90 mmFront panel controller, the printed circuit board in 3D

Front panel controller

birdybro/FPGA_Amp

FPGA based audiophile phono preamp and amp integrated unit idea. WIP

Size
150 × 90 mm
Copper layers
6
Thickness
1.6 mm
Parts
115
Nets
147
Pads
548
Tracks, vias
1,827, 327
Pours
3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
12 Aug 2026
Updated
16 Aug 2026

Overview

Front panel controller is an open-source printed circuit board by birdybro, from the birdybro/FPGA_Amp repository on GitHub, published under the GPL-3.0 licence. It is a 6-layer board of 150 × 90 mm with 115 parts on 147 nets, routed with 1,827 tracks and 327 vias.

It is built around the STM32H753ZIT6, TPS61165DRVR and MBR0540T1G, with the SMBJ15A among its other parts. Its parts include 41 capacitors, 38 resistors, 7 connectors, 5 ICs and 3 diodes. It belongs with the audio and music boards and the STM32 boards of this library.

Main components

4

README

hardware/kicad/front_panel_motor_eval_rev_a/README.md

Motor-volume evaluation PCB — revision A

This is the first physical KiCad design derived from the product hardware specification. It isolates the electrically noisy and mechanically uncertain motor-volume subsystem so it can be measured before committing it to the large LCD/MCU front-panel board.

Open front_panel_motor_eval.kicad_pro in KiCad 10. The checked board was generated and verified with KiCad 10.0.5. KiCad does not live-reload files changed by the generator, so close and reopen the schematic/PCB editor after an external regeneration. Do not hand-edit generated connectivity without also updating generate.py.

Verified artifact

The checked-in board is an 80 x 48 mm, four-copper-layer EVT daughterboard with 44 schematic parts, four M3 mounting holes, 28 named nets, 235 routed segments, and 28 vias. The last clean run reports:

text
schematic ERC violations:  0
PCB DRC violations:        0
unconnected PCB items:     0
minimum routed width:      0.25 mm
minimum via drill:         0.35 mm

The bottom and inner-1 layers are GND pours. Inner-2 is reserved as POWER but is not used as an indiscriminate plane in this small prototype. Connector and test-point functions are labeled on silkscreen. R19/C10 carry KiCad DNP flags, and placement export excludes them.

Electrical intent

  • 4.75–5.25 V motor input for the Bourns PRM16 4.5 V / 100 mA prototype motor.
  • DRV8874 in PH/EN control mode with 33 ohm input damping and 100 kilohm fail-off pulldowns.
  • 10 kilohm IPROPI resistor: nominal 0.45 V at 100 mA using the datasheet's nominal 450 microamp/amp scaling. This is stall telemetry, not precision metrology; the datasheet permits substantial absolute error below 0.4 A.
  • 14.7/10 kilohm VREF divider and 10 kilohm IPROPI resistor: nominal hardware current regulation near 297 mA. This threshold and the 500 mA PTC are not released values until motor start/stall measurements are complete.
  • IMODE uses 62 kilohms to select cycle-by-cycle regulation and latched-off overcurrent behavior. Firmware still detects ordinary stalls from IPROPI and stops without waiting for device OCP.
  • Dual 10 kilohm-class potentiometer tracks are excited ratiometrically from MCU 3.3 V. Their filtered wipers carry position only and never audio.
  • R19/C10 are deliberately DNP EMI-tuning sites. They may only be populated from measured motor emissions and driver-current evidence.

Connectors

J1 is keyed motor power. J2 is the prototype MCU interface. J3 is a separate twisted motor pair. J4 carries the two position tracks. Separating J3 from J4 prevents PWM current from sharing position-sensor conductors.

This is an EVT instrument, not a production-released board. The PRM16 has a published 15,000-cycle rotational life, while the product requirement remains 100,000 qualified full-range cycles.

The DRV8874 PowerPAD is assigned to GND using the standard non-via-in-pad KiCad HTSSOP footprint. That is suitable for low-current motor evaluation only after assembly inspection; a production layout must close copper area, thermal vias, paste aperture, and fabricator capability from measured dissipation. The 0.25 mm routes are ample for the candidate's published 100 mA maximum motor current but are not evidence for an unselected larger mechanism. Connector families, PTC trip/hold rating, TVS selection, current threshold, and optional snubber remain provisional until bench measurements.

Primary component references are the TI DRV8874 datasheet and the Bourns PRM16 datasheet. The route was produced with Freerouting v2.2.4 through KiCad's DSN/SES interchange. Freerouting is intentionally not vendored.

Commands

text
make kicad-motor-generate
make kicad-motor-route FREEROUTING_JAR=/path/to/freerouting.jar
make kicad-motor-check
make kicad-motor-fab

kicad-motor-route starts from generated placement and can occasionally leave an unrouted item because the open autorouter is heuristic. The mandatory check target fails in that case; rerun the route rather than accepting an incomplete board. Fabrication outputs are generated under build/kicad/front_panel_motor_eval/fab/ and are intentionally not committed. Passing export is not an instruction to order boards: peer layout review, mechanical fit, sourcing, assembly rules, and the provisional items above are still open.

Parts

115
QtyValueFootprintReferences
21100nF_X7RC_0402_1005MetricC10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C25, C27, C34, C40, C41 +5
2033RR_0402_1005MetricR10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 +4
710kR_0603_1608MetricR41, R45, R46, R47, R48, R49, R50
4100kR_0603_1608MetricR1, R2, R4, R42
41uF_X7RC_0603_1608MetricC24, C26, C33, C48
4M3_CHASSISMountingHole_3.2mm_M3H1, H2, H3, H4
210pF_C0G_DNPC_0402_1005MetricC30, C31
212pF_C0GC_0402_1005MetricC28, C29
22.2kR_0603_1608MetricR43, R44
22.2uF_LOW_ESRC_0805_2012MetricC22, C23
222RR_0402_1005MetricR30, R31
222uF_6V3_X7RC_1210_3225MetricC3, C4
2600R@100MHzL_0603_1608Metric_Pad1.05x0.95mm_HandSolderFB1, FB2
1+12V_UITestPoint_Plated_Hole_D2.0mmTP1
1+3V3TestPoint_Plated_Hole_D2.0mmTP2
10RR_0402_1005MetricR40
11.5A_PTCFuse_1206_3216MetricF1
1100nFC_0603_1608MetricC32
1100nF_25V_X7RC_0603_1608MetricC2
110uF_25V_X7RC_1210_3225MetricC1
110uF_X7RC_0805_2012MetricC46
110uH_1AL_Bourns-SRN4018L2
11kR_0603_1608MetricR51
11uF_50V_X7RC_1206_3216MetricC6
12.2uH_4AL_Bourns_SRN6045TAL1
1220nF_X7RC_0603_1608MetricC7
125MHz_10pFCrystal_SMD_3225-4Pin_3.2x2.5mmY1
13.32R_1%R_0805_2012MetricR3
13.3nF_X7RC_0603_1608MetricC5
132.768kHz_7pFCrystal_SMD_3215-2Pin_3.2x1.5mmY2
14.7uF_X7RC_0805_2012MetricC21
1BL_FBTestPoint_Plated_Hole_D2.0mmTP7
1BOOT0PinHeader_1x02_P2.54mm_VerticalJP1
1CORTEX_SWDPinHeader_2x05_P1.27mm_VerticalJ7
1DIGITAL_BOARD_CONTROLPinHeader_2x08_P2.54mm_VerticalJ5
1GNDTestPoint_Plated_Hole_D2.0mmTP3
1GREEN_STATUSLED_0603_1608MetricD3
1IS42S16160J-6TLI_32MiBTSOP-II-54_22.2x10.16mm_P0.8mmU2
1LCD_LED_ATestPoint_Plated_Hole_D2.0mmTP6
1MBR0540T1GD_SOD-123D2
1MOTOR_VOLUME_BOARDPinHeader_2x06_P2.54mm_VerticalJ4
1NHD-5.0-800480AF-ASXP-CTP_TFTMolex_54104-4031_1x40-2MP_P0.50mm_HorizontalJ2
1NHD_CTP_6PMolex_52271-0679_1x06-2MP_P1.00mm_HorizontalJ3
1NRSTTestPoint_Plated_Hole_D2.0mmTP8
1PANEL_CONTROLSPinHeader_2x08_P2.54mm_VerticalJ6
1RESETPanasonic_EVQPUJ_EVQPUASW1
1SMBJ15AD_SMBD1
1STM32H753ZIT6LQFP-144_20x20mm_P0.5mmU1
1TPS61165DRVRWSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm_ThermalViasU5
1TPS62132RGTR_3V3_3AVQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm_ThermalViasU4
1UI_12V_INPUTJST_VH_B2P-VH-B_1x02_P3.96mm_VerticalJ1
1VCAP_CORETestPoint_Plated_Hole_D2.0mmTP4
1VDDATestPoint_Plated_Hole_D2.0mmTP5
1W25Q256JVSIQ_32MiBSOIC-8_5.3x5.3mm_P1.27mmU3

More from birdybro/FPGA_Amp

3
  • 4 layers130 × 90 mmPhono adc eval, the printed circuit board in 3D

    Phono adc eval

    birdybro/FPGA_Amp

    FPGA based audiophile phono preamp and amp integrated unit idea. WIP

    139 partsGPL-3.0
  • 4 layers112 × 72 mmDac line output eval, the printed circuit board in 3D

    Dac line output eval

    birdybro/FPGA_Amp

    FPGA based audiophile phono preamp and amp integrated unit idea. WIP

    89 partsGPL-3.0
  • 4 layers80 × 48 mmFront panel motor eval, the printed circuit board in 3D

    Front panel motor eval

    birdybro/FPGA_Amp

    FPGA based audiophile phono preamp and amp integrated unit idea. WIP

    48 partsGPL-3.0

Similar boards

  • 4 layers155 × 69.8 mmDisplayunit, the printed circuit board in 3D

    Displayunit

    muccc/WomoLIN

    Open Source Steuerung von LIN Bus Geräten im Caravan Bereich.

    143 parts84GPL-3.0
  • 6 layers80 × 80 mmV2ultimateflightcomp, the printed circuit board in 3D

    V2ultimateflightcomp

    codinga593/IRIS

    A next generation model rocket focused on a precise propulsive landing on a tower.

    144 parts3
  • 4 layers80 × 80 mmStm32simh, the printed circuit board in 3D

    Stm32simh

    bson/stm32simh

    96 partsMIT
  • 4 layers95.5 × 91 mmBrain PCB, the printed circuit board in 3D

    Brain PCB

    oudehm/seniorDesignPCB

    Editable KiCad projects for the brain, light, power, and pump boards.

    86 parts
  • 2 layers180 × 130 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hacker-devices

    Full-cycle hardware designs for security research devices — each device is a subfolder with its own README, schematics, PCB layout, and software stack

    5 parts2

Questions

How big is the Front panel controller PCB?

It measures 150 × 90 mm and has 6 copper layers, 1.6 mm thick.

What parts does the Front panel controller use?

115 parts, built around the STM32H753ZIT6, TPS61165DRVR, MBR0540T1G and SMBJ15A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Front panel controller KiCad files?

From the birdybro/FPGA_Amp repository on GitHub, at the commit this page was made from: the board is hardware/kicad/front_panel_controller_rev_a/front_panel_controller.kicad_pcb and its schematic hardware/kicad/dac_line_output_eval_rev_a/dac_line_output_eval.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Front panel controller design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).