

Battery management system
- Size
- 100 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 195
- Nets
- 149
- Pads
- 659
- Tracks, vias
- 1,308, 357
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 13 Aug 2023
- Updated
- 2 Jul 2025
Overview
Battery management system is an open-source printed circuit board by benediktibk, from the benediktibk/battery-system repository on GitHub. It is a 4-layer board of 100 × 100 mm with 195 parts on 149 nets, routed with 1,308 tracks and 357 vias.
It is built around the ICL7660N, L6982CDR and FT230XS-R, with the LT8584EFE#PBF, AT24C512CN and STC3100IST among its other parts. Its parts include 67 capacitors, 48 resistors, 20 diodes, 16 ICs and 14 transistors. It belongs with the power boards and the STM32 boards of this library.
Main components
12ICL7660N
DIP-83V~9.5V DIP-8 Charge Pumps ROHSHGSEMIDC-DC ConvertersL6982CDR
SO-8-40℃~+150℃@(TJ) 1 20uA 2A 3.5V~38V 400kHz 850mV~38V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Frequency synchronization、Built-in LDO regulator Step-down type Yes SO-8 DC-DC Converters ROHSSTMicroelectronicsDC-DC ConvertersFT230XS-R
SSOP-16-150mil-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART SSOP-16-150mil USB Converters ROHSFTDIUSB ConvertersLT8584EFE#PBF
TSSOP-16-EP-40℃~+125℃ 2.5A 2.5V~5.3V 2.5mA Balancing IC Support TSSOP-16-EP Battery Management ROHSAnalog DevicesBattery ManagementAT24C512CN
DIP-8-40℃~+105℃ 1.7V~5.5V 1MHz 2,000,000 Cycles 200 Years 3ms 512Kbit Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C DIP-8 EEPROM ROHSHGSEMIEEPROMSTC3100IST
MiniSO-8-40℃~+85℃ 1 2.7V~5.5V 2uA I2C Lithium Battery Monitoring IC Not supported Not supported 欠压锁定 MiniSO-8 Battery Management ROHSSTMicroelectronicsBattery ManagementBAT54WS
SOD-3231 Independent 100mA 1V@100mA 2uA@25V 30V 600mA SOD-323 Schottky Diodes ROHSDiodes IncorporatedSchottky DiodesDMN3404L
SOT-23-55℃~+150℃ 1 N-channel 1V 29pF 305pF 30V 38mΩ@10V 3nC 5A 65pF 750mW N-Channel ±20V SOT-23 MOSFETs ROHSYTLMOSFETsBS250FTA
SOT-23MOSFETsTECH PUBLICSBR2065D1
TO-252-3-55℃~+150℃ 140A 20A 400uA@65V 630mV@20A 65V TO-252-3 Super Barrier Rectifiers (SBR) ROHSDiodes IncorporatedSuper Barrier Rectifiers (SBR)BLM18P
QFN-24_4X4QFN-24_4X4 SMT ROHSShenzhen Better Life Elec S&TUncategorisedRLB0914-220KL
插件,D8.7xL12mm1.9A 22uH 4.5A 90mΩ ±10% 插件,D8.7xL12mm Power Inductors ROHSBournsPower Inductors
Parts
195| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 100nF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C17, C18, C21, C23, C24, C25, C26, C27, C29, C30, C31, C32, C34, C36 +4 |
| 15 | 10uF | benediktibk:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C5, C9, C11, C12, C13, C14, C22, C43, C44, C50, C51, C57, C58, C64, C65 |
| 11 | 10kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8, R12, R19, R20, R21, R22, R23, R24, R30, R31, R32 |
| 10 | 1uF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C6, C10, C28, C33, C35, C42, C49, C56, C63 |
| 10 | 47uF | benediktibk:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C4, C8, C41, C45, C48, C52, C55, C59, C62, C66 |
| 10 | BAT54WS | benediktibk:D_SOD-323 | D1, D2, D4, D5, D6, D7, D8, D9, D10, D11 |
| 8 | 220kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R33, R34, R37, R40 |
| 7 | DMN3404L | benediktibk:SOT-23 | Q3, Q4, Q5, Q6, Q7, Q9, Q14 |
| 7 | heatsink_18x18 | benediktibk:heatsink_18x18 | H5, H6, H7, H8, H9, H10, H11 |
| 6 | 4.7kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R25, R26, R45, R46, R47, R48 |
| 5 | 100kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R35, R36, R38, R44 |
| 5 | BS250FTA | benediktibk:SOT-23 | Q8, Q10, Q11, Q12, Q13 |
| 5 | SBR2065D1 | benediktibk:SBR2065D1 | D3, D17, D18, D19, D20 |
| 4 | 22nF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C40, C47, C54, C61 |
| 4 | 47nF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C46, C53, C60, C67 |
| 4 | LT8584EFE#PBF | benediktibk:SOP65P640X110-17N | IC1, IC2, IC3, IC4 |
| 4 | MountingHole_Pad | benediktibk:MountingHole_6.4mm_M6_Pad_TopBottom | H1, H2, H3, H4 |
| 4 | NA6252-ALD | benediktibk:SOP250P1524X1143-8N | T1, T2, T3, T4 |
| 3 | 100Ohm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R27, R28, R29 |
| 2 | 120Ohm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R17, R18 |
| 2 | 24kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R39, R41 |
| 2 | 27Ohm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15, R16 |
| 2 | 390kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R11 |
| 2 | 39kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R14 |
| 2 | 47pF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19, C20 |
| 2 | BLM18P | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | FB1, FB2 |
| 2 | ICL7660 | benediktibk:SOIC-8_3.9x4.9mm_P1.27mm | U4, U5 |
| 2 | L6982CDR | benediktibk:SO-8_3.9x4.9mm_P1.27mm | U2, U3 |
| 2 | LM2904M8-13 | benediktibk:MSOP-8_3x3mm_P0.65mm | U10, U11 |
| 2 | RLB0914-220KL | benediktibk:RLB0914220KL | L1, L2 |
| 2 | TJ40S04M3L | benediktibk:TO-252-2 | Q1, Q2 |
| 1 | 10nF | benediktibk:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15 |
| 1 | 200kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 20A | benediktibk:KEYSTONE_blade_fus_holder | F1 |
| 1 | 2mOhm/5W | benediktibk:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R5 |
| 1 | 36kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R42 |
| 1 | 4.7uF | benediktibk:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16 |
| 1 | 43kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 68kOhm | benediktibk:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R43 |
| 1 | AMPHENOL_micro_usb_10118194-0001LF | benediktibk:AMPHENOL_10118194-0001LF | J5 |
| 1 | ARM-JTAG-SWD | benediktibk:SAMTEC_FTSH-105-01-F-DV-P-TR | J6 |
| 1 | AT24C512C | benediktibk:SOIC-8_3.9x4.9mm_P1.27mm | U8 |
| 1 | CELLS | benediktibk:rspro_header_5pin_5_08mm | J2 |
| 1 | Charge | benediktibk:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Discharge | benediktibk:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | FT230XS | benediktibk:SSOP-16_3.9x4.9mm_P0.635mm | U6 |
| 1 | NCT75DR2G | benediktibk:SOIC-8_3.9x4.9mm_P1.27mm | U9 |
| 1 | RESET | benediktibk:TS026650BK100SCRD | IC5 |
| 1 | STC3100 | benediktibk:MSOP-8_3x3mm_P0.65mm | U1 |
| 1 | STM32L071CZTx | benediktibk:LQFP-48_7x7mm_P0.5mm | U7 |
| 1 | TEMP_CELL1 | benediktibk:rspro_header_4pin_3_5mm | J7 |
| 1 | TEMP_CELL2 | benediktibk:rspro_header_4pin_3_5mm | J8 |
| 1 | TEMP_CELL3 | benediktibk:rspro_header_4pin_3_5mm | J9 |
| 1 | TEMP_CELL4 | benediktibk:rspro_header_4pin_3_5mm | J10 |
| 1 | UART_RX | benediktibk:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D13 |
| 1 | UART_TX | benediktibk:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D12 |
| 1 | VBAT_DISCHARGE | benediktibk:rspro_header_2pin_5_08mm | J1 |
| 1 | green | benediktibk:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D14 |
| 1 | red | benediktibk:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D15 |
| 1 | yellow | benediktibk:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D16 |
More from benediktibk/battery-system
2- 2 layers100 × 85 mm

- 2 layers25 × 25 mm

Similar boards
- 2 layers12 × 31 mm

- 4 layers42 × 50 mm

SimpleFC G
wangyeee/OpenHardware
Collections of hardware design related to my drone project.
134 parts10BSD-3-Clause - 2 layers120 × 100 mm

Root
GonzaCerv/noah-hardware
This repo contains all the hardware description for the Noah project. Here lies 3D models, electronics PCB and Firmware software of the robot.
127 parts28MIT - 2 layers63.5 × 22.9 mm

LoRaWan1262 jlc
svcguy/LoRaWAN-Feather-Hardware
Schematic and PCB for a Feather-compatible, LoRaWAN-compatible board
86 parts4 - 4 layers61 × 46 mm

- 2 layers35 × 39 mm

- 4 layers138.8 × 77 mm

- 4 layers

IONPAK2
m-labs/ionpak
A modern, low-cost universal controller for hot-cathode ionization vacuum gauges. (WIP)
259 parts23
Questions
How big is the Battery management system PCB?
It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Battery management system use?
195 parts, built around the ICL7660N, L6982CDR, FT230XS-R and LT8584EFE#PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Battery management system KiCad files?
From the benediktibk/battery-system repository on GitHub, at the commit this page was made from: the board is hardware/battery-management-system/battery-management-system.kicad_pcb and its schematic hardware/battery-management-system/battery-management-system.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Battery management system design in my own project?
Its repository states no licence, so its author keeps all rights: ask benediktibk before reusing the design.