Skip to the content
2 layers138 × 162 mmRemora Nucleo F446ZE Hat, the printed circuit board in 3D

Remora Nucleo F446ZE Hat

ben-jacobson/RemoraNucleoHatPCB1

Cost-effective, customisable LinuxCNC motion control unit.

Size
138 × 162 mm
Copper layers
2
Thickness
1.6 mm
Parts
179
Nets
274
Pads
748
Tracks, vias
1,204, 170
Pours
16
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
2 Jun 2025
Updated
3 Jun 2026

Overview

Remora Nucleo F446ZE Hat is an open-source printed circuit board by ben-jacobson, from the ben-jacobson/RemoraNucleoHatPCB repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 138 × 162 mm with 179 parts on 274 nets, routed with 1,204 tracks and 170 vias.

It is built around the AM26LS31CDRE4, MCP6042-I/P and XL1509-12, with the XL1509-5.0, LTV-247 and TL431A among its other parts. Its parts include 74 resistors, 29 connectors, 21 capacitors, 18 ICs and 11 fuses.

Main components

9

README

README.md

Remora Nucleo-144 Hat PCB.

Work in progress design for a cost-effective, highly customisable LinuxCNC motion control unit.

Form factor is a hat/shield for ST Nucleo-144 evaluation board running Remora. Requires a WIZNet TOE for Ethernet control. A link to a specific recommended version of Remora can be found below but other versions should work. This unit is capable of controlling a variety of machine types including CNC milling machines, routers, lathes, laser and plasma cutters.

Schematics and board layout are editable with Kicad 9. Gerbers and PDF's of the schematics will become available on release. At this stage the design is pre-release with a lot of validation/testing/design work pending.

Proposed Features

  • Low cost: Board can be fabricated via PCBWay, parts can be ordered from Digikey/Mouser/Element14. Digikey part numbers are written into the BOM for easy ordering. My latest build was sponsored by PCBWay but their estimated cost was just under the $100USD mark not including shipping
  • Approachable: Goal is to be well documented, providing step by step build guides.
  • Moderate skill requirement: SMT soldering skills are required but the pad sizes are forgiving enough for hand soldering. Hot air or reflow oven soldering is possible but not required.

Current spec

  • Nucleo-144 Hat for 6 axis LinuxCNC motion control using custom port of Remora built for STM32. Board may also support GrblHAL but is not yet tested.
  • Up to 6 axes of isolated, step generation. Default max step gen rate in Remora is 40Khz but the driver circuitry has been tested to generate clean step pulses up to 100Khz. Can be used with any 5V single ended or differential stepper driver. Unused axes can be reconfigured as differential digital outputs.
  • IO: 16x digital inputs, 8x NPN digital outputs. Outputs are sink logic/open collector, protected by a fuse and can sink up to 40mA of current.
  • Most outputs can be configured to drive PWM signals, see the readme in the firmware below for available pins and how to configure this.
  • IO: 2x analog inputs (non isolated)
  • 1x 0-5v / 0-10v DAC for spindle control. Additional spindle control such as direction or indexing can be achieved with IO.
  • 24V DC power input for powering the Nucleo which in turn supplies 5V and 3.3V to sections of the board that are isolated. Galvanic isolation between Nucleo and external devices is achieved by supplying your own isolated 24V supply to the separate input. A jumper can be configured on board to powering the board with only one supply, but will break the isolation.
  • Console logging is available via a UART header (TX only, RX is not used by firmware).

Future Specs

  • PSU's seem to be fine handling 18-28V, need to test this before officially marking this as in spec.
  • There is an experimental single ended ABZ Rotary Encoder Input, it was hobbled together from parts already available on the BOM as an experiment. Predictably it does not perform any high speed task, it would probably even struggle with a slowly moved rotary encoder pot. Will eventually replace with a real design.

Build guide

This is intended to be a DIY project, not as a complete product. A link will soon be provided to a place to order on PCBWay, or you can self source the parts using the DigiKey part numbers. Please see the jumper settings and connecting to USB section as they are contain important information needed to get started.

Jumper settings: Before powering on your Nucleo hat, ensure that the following two jumpers are set: JP1: Please remove this jumper entirely JP3: Place to the far right position, indicating VIN as per the picture in JP3Setting.png

Connecting to USB: Take care when connecting the device to USB. Please make sure that the board is fully powered up before connecting to USB. Failing to do so could result in damage to your computer. This is not an issue with our design, but in the Nucleo itself. For more info see 7.4.2 in the Nucleo 144 datasheet. The device does not need USB to run. USB can be used to flash new firmware or monitor serial output. For serial output, the provided TX pin header is a better choice if you'd like constant serial monitoring during use.

Todos

  • Perform full board testing with a real load and measure current draws, re-design the PSU's for beter efficiency, line/load regulation, ripple rejection, etc.
  • Add PTC resettable fuses to PSU
  • Commit release Gerber files to repo and PDF
  • Put up some photos of the completed PCB.
  • Put up marketplace product on PCBWay
  • Research how we might be able to support Servo drives
  • Test GRBLHal

If you'd like to contribute into this project

Reach out - would love some help with any improvement. Would be especially grateful for anyone willing to help with testing, further engineering support, etc.

Firmware

Firmware can be found in separate repo: https://github.com/ben-jacobson/Remora-STM32F4xx-PIO

Parts

179
QtyValueFootprintReferences
42180RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2, R3, R10, R11, R12, R13, R14, R15, R16, R29, R30, R31, R32, R33, R34, R35 +26
194K7Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R89, R90, R100, R105, R106, R107, R108, R109, R110, R111, R112, R113, R114, R115, R116 +3
15100nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC9, C10, C15, C16, C21, C22, C27, C28, C29, C33, C34, C35, C36, C37, C38
14Conn_01x04_Socket691412120004B:691412120004BJ7, J9, J11, J13, J15, J17, J19, J20, J22, J23, J26, J27, J28, J29
11PRG18BB330MB1RBFuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolderF1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11
10LTV-247Package_SO:SOP-16_4.4x10.4mm_P1.27mmU4, U6, U7, U8, U9, U10, U11, U12, U14, U17
91K2Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR85, R86, R87, R88, R91, R92, R93, R99, R101
9Conn_01x02_Socket691412120002B:691412120002BJ8, J10, J12, J14, J16, J18, J21, J24, J30
9MountingHole_PadMountingHole:MountingHole_2.7mm_M2.5_DIN965_Pad_TopBottomH1, H2, H3, H4, H5, H6, H7, H8, H9
4LEDDiode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1, D2, D5, D6
3100RResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR102, R103, R104
3AM26LS31CDRPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU5, U13, U15
2180uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC7, C8
21uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC5, C6
2470uFCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC3, C4
25.6V ZenerPackage_TO_SOT_SMD:SOT-23D7, D8
268uH / 1AInductor_SMD:L_APV_ANR8040L1, L2
2B330AFDiode_SMD:D_SMAD3, D4
2Conn_02x35_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x35_P2.54mm_VerticalJ1, J4
2Peripheral->Logic VDD JumperJumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mmJP1, JP2
110KResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR98
110K 25 turn trimpotPotentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV1
124V Isolated691412120002B:691412120002BJ6
124V Logic691412120002B:691412120002BJ5
1BC847Package_TO_SOT_SMD:SOT-23Q1
1Isolated->Logic GND JumperJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP4
1Isolated->Logic VDD JumperJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP3
1MCP6042Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU16
1SW_PushButton_Switch_SMD:SW_SPST_Omron_B3FS-100xPSW1
1Spindle Out691412120002B:691412120002BJ25
1TL431APackage_TO_SOT_SMD:SOT-23U18
1UART_TXConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Wiznet W5500 Eval ModuleW5500EvalModule:W5500EvalModuleU1
1XL1509-12Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU2
1XL1509-5.0Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU3

Similar boards

  • 2 layers34.6 × 28.4 mmDVI adapter, the printed circuit board in 3D

    DVI adapter

    openconcepts-ar/accel2d

    This project aims to provide a graphics server system based on hardware accelerated graphics, and a easy way to develop the graphics primitives.

    51 parts1
  • 2 layers129.5 × 83.5 mmColordance brain, the printed circuit board in 3D

    Colordance brain

    ademuri/colordance-circle

    An art project that uses arrays of colored lights around a circle to create kaleidoscopic colored shadows.

    131 parts4Apache-2.0
  • 2 layers116.8 × 92.2 mmControllerStage, the printed circuit board in 3D

    ControllerStage

    pommen/Programmable_Load

    132 parts
  • 4 layers52.5 × 59.7 mmESPHome Indoor Multi Sensor, the printed circuit board in 3D

    ESPHome Indoor Multi Sensor

    mikelawrence/esphome-indoor-multi-sensor-hardware

    ESPHome Indoor Multi-Sensor hardware. This design supports Radar/PIR Presence, Temperature, Humidity, Pressure, Light, CO2, CO, VOC, NOX and PM sensors.

    113 parts14CERN-OHL-P-2.0
  • 2 layers83.8 × 50.8 mmShunt charge controller, the printed circuit board in 3D

    Shunt charge controller

    grillbaer/solar-power-supply

    Solar power harvesting for micro controller projects with li-Ion battery and highly efficient charge controller

    16 parts3MIT
  • 2 layersWarduxere append, the printed circuit board in 3D

    Warduxere append

    josefjebavy/warduxere

    Wireless Arduino with low power consumption

    140 parts3
  • 2 layers99.1 × 99.1 mmMessplatine, the printed circuit board in 3D

    Messplatine

    PhyPiDAQ/EducatorsGuide

    Tutorial for educators and examples of educational physics experiments

    51 parts1BSD-2-Clause

Questions

How big is the Remora Nucleo F446ZE Hat PCB?

It measures 138 × 162 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Remora Nucleo F446ZE Hat use?

179 parts, built around the AM26LS31CDRE4, MCP6042-I/P, XL1509-12 and XL1509-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Remora Nucleo F446ZE Hat KiCad files?

From the ben-jacobson/RemoraNucleoHatPCB repository on GitHub, at the commit this page was made from: the board is Remora Nucleo F446ZE Hat.kicad_pcb and its schematic 1ch_output_driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Remora Nucleo F446ZE Hat design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).