Skip to the content
2 layers48.9 × 73.8 mmBeep pcb v1.4, the printed circuit board in 3D

BEEP base v2 (wooden + steel frame, 4 weight sensors)

Size
48.9 × 73.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
22
Nets
75
Pads
173
Tracks, vias
579, 31
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
9 Nov 2019
Updated
9 Nov 2021

Overview

Beep pcb v1.4 is an open-source printed circuit board by beepnl, from the beepnl/measurement-system-v2 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 48.9 × 73.8 mm with 22 parts on 75 nets, routed with 579 tracks and 31 vias.

It is built around the HX711. Its parts include 9 connectors, 5 ICs and 1 resistor. It belongs with the sensors and measurement boards of this library.

Main components

1

README

README.md

BEEP - Measurement system

This is a repo containing the files to create the open source hardware for the Beep measurement system.

Measurement system parts

The measurement system casing is designed as both an electonics/sensor housing, as well as a weighing frame. The outer casing is assembled in four pieces (2 tops, 2 bottoms) out of 18mm thick plate 'Betonplex' (glued multiplex with water resistant top and bottom layer). The wooden top and bottom are connected together by the 2 weight sensor (aluminium) blocks, held in place by 2 weight sensor brackets each. The left and right part are held together with 2 stainless steel tubes, that are screwed on the wood. At one side tightly, using wood parkers, at the other side loosely, using m4 bolts that go inside the inserts. By this connection, the total size of the frame is adjustable for different types of hives.

BEEP measurement system casing

Frame

The folder 'frame' contains two folders: wood and stainless steel.

Wood

The 2D drawings in both Illustrator format and DXF (required by most milling parties).

BEEP measurement system casing - Milling instruction

This is a picture of the milling software, with which we mill 42 pieces (21 tops, 21 bottoms) out of an 2440 x 1220 x 18 mm Betonplex.

BEEP measurement system - Milling process

Stainless steel

The 3D and 2D drawings of the stainless steel tube, and the sensor bracket are in this folder. They can be ordered at companies lasering steel.

BEEP measurement system - Stainless steel parts

Electronics

The electronics of the measurement system are bundled together on the Beep PCB, which connects an Arduino, a LoRa (wireless network) chip and the sensors via Grove connectors together.

The folder 'electronics' contains two folders: gerber and kicad.

With the Gerber files, you can directly order a PCB. It contains all files required for the manufacturing of the PCB.

With the Kicad files, you can edit the PCB and it's components in the open source PCB creation software Kicad (http://kicad-pcb.org/).

Schematic

NB: There is an error in the PCB, the one wire temperature sensor DS18b20 cannot work on analog port A7 (the A6 and A7 IO pins can only be used as analog pins, not as digital IO). So you have to use A4, or A5 to connect one wire sensor(s) to. So you also have to add the 4k7 resistor between V+ and the one wire data pin yourself, since the resistor on the PCB is connected to V+ and A7.

The schematic can be found in the PDF (https://github.com/beepnl/measurement-system-v2/blob/master/electronics/Beep-pcb-v1.4-schematic.pdf)

PCB

BEEP measurement system - PCB

Assembly

BEEP measurement system - PCB

BEEP measurement system - PCB

Firmware

In the 'firmware' folder, the ultra low power Arduino code is shared to use with the PCB and complete the measurement system.

Place the folder 'Beep-low-power' inside your Arduino folder and set up your own LoRa connection details to send the data. Send an e-mail to pim@beep.nl, to add your Measurement system Device EUI to your Beep app account and receive it's measurements in the app.

Improvements

If you have improvements, or ideas for creating a better frame, please send an e-mail to pim@beep.nl explaining your thoughts. Or just fork this repo, and do a pull request with you adjustments, or additions.

Parts

22
QtyValueFootprintReferences
2HX711HX711:HX711U2, U3
13V3 TTL FTDIPin_Headers:Pin_Header_Straight_1x06_Pitch2.54mmJ5
1A4 on DTJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP3
1A5 on SCKJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP4
1Batt to VCC/3V3 (solder)Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mmJP6
1Dragino-LoRa-MiniNexus:Dragino LoRa MiniU5
1Grove 1=DHT22, 2=NC/D5 DraginoConnectors:Grove_1x04J8
1Grove 1=Mic, 2=DS18B20Connectors:Grove_1x04J9
1Grove I2C, 1=SDA, 2=SCLConnectors:Grove_1x04J2
1NexusNexus:NexusU1
1Nexus Batt -> 3V3/PWRJumper:SolderJumper-3_P1.3mm_Bridged2Bar12_RoundedPad1.0x1.5mmJP7
1PowerPin_Headers:Pin_Header_Straight_1x02_Pitch2.00mmJ1
1RResistors_Universal:Resistor_SMD+THTuniversal_1206_RM10_HandSolderingR1
1Sensor continuous powerJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP2
1Sensor switchable powerJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP1
1VIN TTL = VCCJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP5
1Weight A/ALLConnectors:Grove_1x04J3
1Weight BConnectors:Grove_1x04J6
1Weight CConnectors:Grove_1x04J7
1Weight DConnectors:Grove_1x04J4
1Whisper LoRaWhisper Lora:Whisper_LoraU4

Similar boards

  • 2 layers15.3 × 19.3 mmKicad hx711 tyny85, the printed circuit board in 3D

    Kicad hx711 tyny85

    IvDm/Z-probe-on-smd-resistors-2512

    Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.

    18 parts150GPL-3.0
  • 2 layers109.2 × 74.9 mmOpenautolab, the printed circuit board in 3D

    Openautolab

    kauzerei/openautolab

    Film developing machine

    30 parts80GPL-3.0
  • 4 layers81.2 × 81.2 mmView base, the printed circuit board in 3D

    View base

    SeedLabs-it/smartknob-hardware

    PCB and CAD files for smartknob devkit

    259 parts47
  • 2 layers128 × 77 mmScale, the printed circuit board in 3D

    Scale

    Jana-Marie/lab-balance

    https://twitter.com/_Jana_Marie/status/1270040286710968321

    59 parts34
  • 2 layers60 × 40 mmForcegauge, the printed circuit board in 3D

    Forcegauge

    szbeni/forcegauge

    Traning for climbing. Load cell with HX711 and real time plotting,

    77 parts18GPL-3.0
  • 2 layers112 × 57 mmCaravansensor, the printed circuit board in 3D

    Caravansensor

    MartinVerges/womolin-waterlevel

    DIY project to build a smart fuel sensor for RVs or in other projects. It is based on air pressure and is able to measure fresh water as well as grey and black water levels with high precision.

    226 parts17
  • 2 layers71.1 × 109.2 mmLora node esp32 smd GPS, the printed circuit board in 3D

    Lora node esp32 smd GPS

    Christophe45/ESP32-Lorawan

    ESP32 Lorawan beehive connected

    38 parts14
  • 2 layers70 × 35 mmOpenWatts, the printed circuit board in 3D

    OpenWatts

    ikonis/OpenWatts

    OpenWatts is a crank-mounted, single-sided cycling power meter built around an ESP32-C3. A bonded strain-gauge bridge and HX711 measure crank torque, while an LSM6DS3 IMU provides cadence and motion wake.

    41 parts12

Questions

How big is the Beep pcb v1.4 PCB?

It measures 48.9 × 73.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Beep pcb v1.4 use?

22 parts, built around the HX711. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Beep pcb v1.4 KiCad files?

From the beepnl/measurement-system-v2 repository on GitHub, at the commit this page was made from: the board is electronics/kicad/beep-pcb-v1.4.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Beep pcb v1.4 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).