

Digiport general
集成USB口和声卡的业余电台数据模式接口盒子
- Size
- 40 × 22.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 73
- Pads
- 184
- Tracks, vias
- 370, 50
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 Jan 2025
- Updated
- 27 Oct 2025
Overview
Digiport general is an open-source printed circuit board by BD5HLI, from the BD5HLI/DigiPort repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 40 × 22.8 mm with 36 parts on 73 nets, routed with 370 tracks and 50 vias.
It is built around the CH340X, CM108B and CH334P, with the CH442E and 1N4148W among its other parts. Its parts include 13 capacitors, 8 resistors, 4 ICs, 3 connectors and 1 diode.
Main components
5CH340X
MSOP-10-20℃~+70℃ 2Mbps 3.3V、5V USB 2.0 USB to serial、USB to Parallel MSOP-10 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersCM108B
LQFP-48(7x7)-20℃~+70℃ 4.5V~5.5V 44.1kHz~48kHz Encoder/decoder I2S、USB LQFP-48(7x7) Audio Interface ICs ROHSCmediaAudio Interface ICsCH334P
QFN-16(3x3)-40℃~+85℃ 0.4mA 3.3V 4 480Mbps 85mA Hub USB 2.0 QFN-16(3x3) USB HUB Controllers ROHSWCH (Nanjing Qinheng Microelectronics)USB HUB ControllersCH442E
MSOP-10-40℃~+85℃ 2 2:1 2ns 3ns 4V~5.5V 550MHz 5Ω 9pF MSOP-10 Analog Switches, Multiplexers ROHSWCH (Nanjing Qinheng Microelectronics)Analog Switches, Multiplexers1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching Diodes
README
README.md简介
面向八重洲FT-891的FT8模式集成接口,内置一个2口的USB2.0 HUB和一个USB声卡,通过一个Type-C接口连接电脑或者手机,解决FT-891没有内置声卡的问题。
本项目采用了Digirig-Mobile项目(https://github.com/softcomplex/Digirig-Mobile )的符号库、封装库和3D器件模型,参考了Digirig DR-891的原理图(https://digirig.net/digirig-dr-891-setup-manual/ )设计,精简了几乎用不到的CM108B GPIO脚的PTT功能,保留了VOX-PTT功能。此外,本项目的被动器件(电阻、电容)均采用0402手焊封装,便于手工焊接。
本项目虽然面向FT-891设计,实际上可以仅使用USB声卡的功能,从而适用于绝大多数带有音频输入输出接口的电台,比如K5、K6手台,配合相应的软件可以实现SSTV、APRS等玩法。
电路板渲染图
电路板正面:

电路板反面:

接口
DigiPort在电脑侧的接口为type c接口,可使用c to a或c to c数据线连接电脑或者手机;在电台侧的接口包括两个3.5mm的4芯TRRS接口,面向电路板器件面、type c接口在右侧时,左上的TRRS接口为音频/PTT接口,左下的TRRS接口为USB接口。
DigiPort的音频/PTT接口定义如下:
/\
| |---------> 尖端 RIG_AFOUT 电台音频输出,接FT-891 DATA口的DATA OUT脚
|--|
| |---------> 第一环 RIG_AFIN 电台音频输入,接FT-891 DATA口的DATA IN脚
|--|
| |---------> 第二环 VOX_PTT 声控PTT,接FT-891 DATA口的PTT脚
|--|
| |---------> 底部 GND 信号地,接FT-891 DATA口的GND脚
__| |__
| | VOX_PTT信号用于没有USB串口的设备控制收发转换,控制源来自CM108B声卡的右声道,推荐采用1kHz或2kHz的单音作为VOX触发信号。
FT-891的DATA插座定义如下:
/-----\ 1脚:DATA IN
/ 6 _ 5 \ 2脚:GND
|4 |_| 3| 3脚:PTT
\ 2 1 / 4脚:SHIFT
\-----/ 5脚:DATA OUT
6脚:SQL DigiPort的电台侧USB接口定义如下:
/\
| |---------> 尖端 +5V 电台USB口的+5V电源脚
|--|
| |---------> 第一环 D- 电台USB口的D-脚
|--|
| |---------> 第二环 D+ 电台USB口的D+脚
|--|
| |---------> 底部 GND 电台USB口的GND脚
__| |__
| | USB Type-B插头定义如下:
/-+=+--+=+-\ 1脚:+5V
/ |=| |=| \
| 1 2 | 2脚:D-
| |
| 4 3 | 3脚:D+
| |=| |=| |
|--+=+--+=+--| 4脚:GND 各目录内容说明
- digiport-891目录下是kicad格式的原理图和PCB图。
- endboard目录下是采用25mm * 25mm * 40mm对扣小铝壳的端板3D图纸。
- 3D-models目录下是部分器件的3D模型,来自Digirig-Mobile项目。
- footprints.pretty目录下是部分器件的封装库,来自Digirig-Mobile项目。
- symbols目录下是部分器件的符号库,来自Digirig-Mobile项目。
致谢
-
感谢LX6FB提供原版DR-891的照片。
-
感谢BG5ARO对端板设计提出了宝贵建议,并提供了CNC加工。
-
感谢BG5BQB提供了3D打印工艺的端板原型样件。
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C3, C6, C7, C8, C9, C10 |
| 4 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C4, C5, C13 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R8 |
| 2 | 1nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C11, C12 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2 |
| 1 | 1.5k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R6 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D1 |
| 1 | 22 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | 4.7k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7 |
| 1 | ATT | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP6 |
| 1 | Audio&PTT | digiport:TRRS-PJ-320A | J1 |
| 1 | CH334P | digiport:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm_ThermalVias | U1 |
| 1 | CH340X | Package_SO:MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | CH442E | Package_SO:MSOP-10_3x3mm_P0.5mm | U4 |
| 1 | CIV_EN | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | CM108B | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | FSKK_EN | digiport:SolderJumper2-BCu | JP5 |
| 1 | FT891/Other | digiport:SolderJumper3-BCu | JP2 |
| 1 | FT891/Other | digiport:SolderJumper2-BCu | JP1 |
| 1 | USB/CIV/CAT | digiport:TRRS-PJ-320A | J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | Yaesu/ICOM | digiport:SolderJumper-BCu-Bridged | JP4 |
More from BD5HLI/DigiPort
1- 2 layers40 × 22.8 mm

Similar boards
- 2 layers334.6 × 100.2 mm

Lira
AndreaGiulianini/lira
57-key 40% + numpad keyboard: Bluetooth/USB-C, hot-swap MX, RMK/Vial, and a built-in USB sound card (3.5 mm headset jack). Generated from source with KiCad.
233 parts2MIT - 2 layers22 × 100 mm

Keyboard
a5632645/final_design
simple digital waveguide synthesizer & simple mpe midi keyboard(pitch bend and pressure)
19 parts4 - 2 layers22.8 × 36 mm

Digirig mobile
softcomplex/Digirig-Mobile
Integrated digital modes interface for amateur radio
64 parts133GPL-3.0 - 4 layers101.6 × 141.7 mm

- 2 layers60 × 50 mm

- 2 layers87.5 × 53 mm

- 2 layers55 × 55 mm

- 2 layers80 × 27 mm

Aom preamp
pranavb104/Electret-Amp-USB
A simple transistor based amplifier for electret condenser type mics coupled with CM108b USB audio interface
49 parts
Questions
How big is the Digiport general PCB?
It measures 40 × 22.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Digiport general use?
36 parts, built around the CH340X, CM108B, CH334P and CH442E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Digiport general KiCad files?
From the BD5HLI/DigiPort repository on GitHub, at the commit this page was made from: the board is digiport-general/digiport-general.kicad_pcb and its schematic digiport-891/digiport-891.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Digiport general design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).