2 layers100 × 45 mm
2 layers72 × 71 mm
Board cell emulator V1
batterylabunipi/Modular_Battery_Emulator9Modular battery emulator for the development and functional testing of Battery Management Systems: the cell emulator
- Size
- 72 × 71 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 63
- Nets
- 42
- Pads
- 177
- Tracks, vias
- 480, 21
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 17 Feb 2022
- Updated
- 30 May 2024
Overview
Board cell emulator V1 is an open-source printed circuit board by batterylabunipi, from the batterylabunipi/Modular_Battery_Emulator repository on GitHub. It is a 2-layer board of 72 × 71 mm with 63 parts on 42 nets, routed with 480 tracks and 21 vias.
It is built around the URB4805YMD-6WR3 and ADS1118IDGS. Its parts include 20 capacitors, 10 resistors, 6 ICs, 6 connectors and 2 diodes.
Main components
2
URB4805YMD-6WR3
DIP,25.4x25.4mm-40℃~+85℃ 1 1.2A 1.5kV 11mm 18V~75V 2200uF 25.4mm 25.4mm 250kHz 50mVp-p 5V 6W 6mA 85% Regulated type Short Circuit Protection、Over Current Protection、Under Voltage Protection、Overvoltage protection DIP,25.4x25.4mm Isolated Power Modules ROHSYLPTECIsolated Power Modules
ADS1118IDGS
VSSOP-10-0.5mm-40℃~+125℃ 150uA 16 1MHz 2 2.048V 2LSB 2V~5.5V 5ppm/℃ 860Hz 8Hz、16Hz、32Hz、64Hz、128Hz、250Hz、475Hz、860Hz Built-in Built-in Built-in SPI Sigma-Delta Support Yes VSSOP-10-0.5mm Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADC)
README
README.mdModular_Battery_Emulator
Modular battery emulator for the development and functional testing of Battery Management Systems: the cell emulator
Parts
63| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | TestPoint | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | TP1, TP2, TP3, TP4, TP5, TP6, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19 +3 |
| 7 | 0 | Capacitors_SMD:C_0805_HandSoldering | R2, R7, R9, R10, R11, R12, R13 |
| 7 | 0.1uF | Capacitors_SMD:C_0805_HandSoldering | C1, C5, C6, C8, C10, C12, C17 |
| 7 | DNM | Capacitors_SMD:C_0805_HandSoldering | C13, C14, C15, C16, R1, R5, R8 |
| 3 | 10k | Capacitors_SMD:C_0805_HandSoldering | R3, R4, R6 |
| 3 | 10uF | Capacitors_SMD:CP_Elec_6.3x7.7 | C2, C3, C4 |
| 2 | DNM | Diodes_SMD:D_0805 | D1, D2 |
| 1 | 0.15uF | Capacitors_SMD:C_0805_HandSoldering | C9 |
| 1 | 1uF | Capacitors_SMD:C_0805_HandSoldering | C7 |
| 1 | 47uF | Capacitors_SMD:CP_Elec_10x10.5 | C11 |
| 1 | ACS723xLCTR-05AB | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U6 |
| 1 | ADS1118IDGS | Housings_SSOP:MSOP-10_3x3mm_Pitch0.5mm | U4 |
| 1 | ADUM3151 | Housings_SSOP:SSOP-20_5.3x7.2mm_Pitch0.65mm | U2 |
| 1 | AUX | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm | J6 |
| 1 | C+ | Connectors:Banana_Jack_1Pin | J5 |
| 1 | C- | Connectors:Banana_Jack_1Pin | J4 |
| 1 | C_in | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J3 |
| 1 | DAC8560IADGKR | Housings_SSOP:MSOP-8_3x3mm_Pitch0.65mm | U3 |
| 1 | ISO COM | Pin_Headers:Pin_Header_Straight_1x10_Pitch2.54mm | J1 |
| 1 | OPA567 | board:Texas_S-PVQFN-N12_ThermalVias | U5 |
| 1 | Power | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J2 |
| 1 | URB4805YMD-6WR3 | board:URB4805YMD-6WR3 | U1 |
Similar boards
- 4 layers29 × 93 mm
Smart penetrometer
ARTS-Laboratory/SPECIES
Design and development of a deployable UAV smart penetrometer
48 parts6CC-BY-SA-4.0 - 4 layers94.3 × 81.8 mm
YukaLink revA
Misaka0x2730/YukaLink
Dual targets USB+ETH ARM JTAG/SWD debugger (BlackMagic port) based on RP2350. JTAG and SWD interfaces are implemented on PIO.
321 parts3GPL-3.0 - 2 layers42.5 × 62.5 mm
Evse
Tinkerforge/evse-bricklet
This Bricklet together with the ESP32 Brick the RS485 Bricklet and the NFC Bricklet form the hardware used in the WARP Charger
92 parts3 - 4 layers127 × 101.6 mm
- 6 layers180 × 110 mm
Reflow station
atwardzik/reflow_station_pcb
This project is currently in a prototype stage. It features PCB project of basic reflow station utilizing 4 phase-controlled triacs steering with attached heaters.
267 parts - 4 layers99.6 × 100 mm
DualPreRegPowerSupply
janni0609/2-Channel-PreReg-Powersupply
A two-channel laboratory bench power supply, 0–36 V / 0–2 A per channel, fully isolated between channels. Each channel pairs a tracking switch-mode pre-regulator with a linear post-regulator, so it has the low output…
379 parts - 2 layers143.3 × 116.6 mm
Questions
How big is the Board cell emulator V1 PCB?
It measures 72 × 71 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Board cell emulator V1 use?
63 parts, built around the URB4805YMD-6WR3 and ADS1118IDGS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Board cell emulator V1 KiCad files?
From the batterylabunipi/Modular_Battery_Emulator repository on GitHub, at the commit this page was made from: the board is board_cell_emulator_V1/board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Board cell emulator V1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask batterylabunipi before reusing the design.