Skip to the content
4 layers117.8 × 152.4 mmOverdrivePedal, the printed circuit board in 3D

Overdrive guitar pedal, made entirely custom in KiCad and Fusion360.

Size
117.8 × 152.4 mm
Copper layers
4
Thickness
1.6 mm
Parts
35
Nets
34
Pads
89
Tracks, vias
126, 8
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Oct 2026
Updated
17 Oct 2026

Overview

OverdrivePedal is an open-source printed circuit board by basimallawala, from the basimallawala/OverdrivePedal repository on GitHub, published under the MIT licence. It is a 4-layer board of 117.8 × 152.4 mm with 35 parts on 34 nets, routed with 126 tracks and 8 vias.

It is built around the TL072, PTV09A-4025F-B103 and NMJ6HFD2-AU. Its parts include 11 resistors, 8 capacitors, 3 diodes, 3 connectors and 1 IC. It belongs with the audio and music boards of this library.

Main components

3

README

README.md

Overdrive Guitar Pedal

A through-hole guitar overdrive pedal designed in KiCad. Op-amp gain stage with diode soft-clipping, a tone control, a volume control, true-bypass switching with an indicator LED, and battery or DC power. Everything (pots, jacks, LED) mounts directly to the PCB, so the board sits behind the enclosure face with nothing but the footswitch wired by hand.

Features

  • Non-inverting TL072 gain stage with symmetric 1N4148 clipping
  • Gain, Tone and Volume controls
  • True bypass via a 3PDT footswitch, with an LED that lights only when the effect is engaged
  • Powered by a 9V battery or a DC jack (the switched jack disconnects the battery when an adapter is plugged in)
  • Battery power switches on automatically when a cable is plugged into the input jack (stereo jack ring wired to battery negative)
  • Fully through-hole, hand-solderable

Circuit overview

Signal path, left to right:

  1. Input: R6 (10k) and C4 (22nF) AC-couple the guitar into the op-amp's non-inverting input. R8 (1M) to ground gives the input a discharge path.
  2. Bias: R4/R3 (10k/10k) from the 9V rail make a 4.5V virtual ground, filtered by C3 (47uF). R5 (1M) feeds that reference into the op-amp input so the signal rides on 4.5V.
  3. Gain stage (U1A): RV1 (500k) in parallel with C6 (100pF) sets the feedback resistance against the R2 (1k) / C5 (220nF) ground leg. D1 and D2 (1N4148, antiparallel) across the feedback network clip the output.
  4. Tone: RV2 (10k) with C1 (22nF) forms a variable low-pass after the gain stage.
  5. Output: C7 (0.1uF) blocks the 4.5V DC offset, R7 (1M) pulls the node to ground, and RV3 (100k) sets output volume.

The unused op-amp half (U1B) is tied off, and C8 (0.1uF) decouples the TL072 supply.

Controls

RefControlValueTaperPart
RV1Gain500kLinearBourns PTV09A-4020U-B504
RV2Tone10kLinearBourns PTV09A-4020S-B103
RV3Volume100kLog (audio)Bourns PTV09A-4020S-A104

Bypass wiring

The footswitch is wired off-board to a 1x9 header (SW1). Each pole's common is the middle lug of its column:

PoleCommonEngagedBypass
AINOV_IN (into effect)jumper to pole B
BOUTOV_OUT (from effect)jumper to pole A
CLED cathodeGNDno connect

IN is the guitar signal, OUT goes to the amp, and OV_IN / OV_OUT are the effect's input and output.

Bill of materials

The full list is in BOM.csv. Key parts:

RefPartNotes
U1TL072DIP-8 (through-hole) package
D1, D21N4148DO-35
D35mm red LED
J4, J5Neutrik NMJ6HFD2Switched 1/4" stereo jacks (input and output)
J1Tensility 54-001305.5 x 2.5mm right-angle DC jack
SW13PDT stomp switchPanel-mounted, wired to the SW1 header
RV1-RV3Bourns PTV09ASee Controls table
PassivesAxial 1/4W resistors, radial ceramic and electrolytic capsAll through-hole

Mechanical notes

  • Pots, jacks and the LED are PCB-mounted, so the board layout and the enclosure drilling have to match exactly. Take hole positions from the PCB, not separately.
  • The PCB mounts on standoffs with M3 screws (3.2mm clearance holes, non-plated).
  • The footswitch mounts to the enclosure with its bushing and nut; only its 9 wires connect to the board.
  • The enclosure is 3D printed. Use heat-set M3 inserts rather than printed threads for any screw that gets removed more than once.
  • Enclosure size is driven by the artwork, so confirm dimensions before finalizing the board outline.

Simulation

The overdrive stage can be simulated with KiCad's built-in ngspice simulator. Tips from the build:

  • Simulate only the Overdrive and DC Bias sheets. Exclude connectors and the footswitch, which have no SPICE models.
  • Replace the input with a VSIN source (for example 500mV amplitude, 1kHz) on the OV_IN net.
  • Give the TL072 a SPICE model and check its pin assignments for every unit, including the power unit.
  • Potentiometers simulate as fixed resistors, so set each wiper position manually.
  • AC sweeps show frequency response only, not clipping. Use transient analysis for clipping.

Repository contents

Adjust this list to match the repo.

  • UmarPedal.kicad_pro, UmarPedal.kicad_sch, UmarPedal.kicad_pcb: KiCad project, schematic and board
  • BOM.csv: bill of materials exported from KiCad
  • Custom symbols and footprints for the Tensility 54-00130, Neutrik NMJ6HFD2 and Bourns PTV09A parts

Designed with KiCad 10.

Known TODOs

  • Confirm U1 is ordered as a DIP-8 part (for example TL072CP), not the SOIC variant.
  • Make sure RV1, RV2 and RV3 carry their own values and footprints in the schematic so the BOM lists three distinct pots.
  • Add the 1x9 header part that matches the SW1 footprint.
  • Confirm the DC jack wiring and polarity against your power supply (the pedal standard is center-negative).
  • Consider reverse-polarity protection on the power input.
  • Check that the C6 part (rated 3kV) physically fits its footprint, or switch to a 50V 100pF ceramic.

Build notes

  1. Solder the low-profile parts first (resistors, diodes), then caps, the IC socket, and finally the pots, jacks and LED.
  2. Wire the footswitch to the SW1 header following the bypass table above.
  3. Test with a 9V supply before closing the enclosure. The 4.5V bias node should read about 4.5V.

Parts

35
QtyValueFootprintReferences
310kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R4, R6
31MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5, R7, R8
3PTV09A-4025F-B103PTV09A-4025F-B103:PTV09A-4025F-B103R9, R10, R12
20.1uCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC7, C8
21N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2
222nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC1, C4
247uFCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC2, C3
2NMJ6HFD2NMJ6HFD2:NEUTRIK_NMJ6HFD2J4, J5
1100pCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC6
11kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2
12.2kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1220nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC5
154-0013054-00130:TENSILITY_54-00130J1
1LEDLED_THT:LED_D5.0mmD3
1LOGOLOGOG***
1TL072Package_DIP:DIP-8_W7.62mmU1
1~Connector_PinSocket_2.54mm:PinSocket_1x09_P2.54mm_VerticalSW1

The 28 most common of 35 parts.

Similar boards

  • 4 layers100 × 100 mmRpi pico kit, the printed circuit board in 3D

    Rpi pico kit

    999matej999/pico-kit-pcb

    198 parts1GPL-3.0
  • 2 layers86.4 × 71.1 mmLovers Rock, the printed circuit board in 3D

    Lovers Rock

    thechakmv/Overdrive-Distortion-Guitar-Pedal

    I created analog guitar effects pedal with two independent, switchable gain stages featuring deliberately opposite midrange voicings to achieve classic Thrash metal rhythm and lead tones: a soft-clipping overdrive with…

    53 parts
  • 2 layers60 × 85 mmIceScreamer, the printed circuit board in 3D

    IceScreamer

    UC3Music/IceScreamer

    A widely known overdrive pedal

    95 parts19
  • 8 layers134 × 114 mmJlcpcb 1x1, the printed circuit board in 3D

    Jlcpcb 1x1

    t-dsp/t-dsp_core

    T-DSP Core 4-layer audio backplane — Teensy 4.1, ESP32, and T-DSP TAC5212 codec module

    172 parts6
  • 2 layers50.5 × 102 mmGuitar waveform proj, the printed circuit board in 3D

    Guitar waveform proj

    HDEmerald/waveform_viewer

    A guitar pedal whose sole purpose is to display the guitar's signal onto a display.

    40 parts1MIT

Questions

How big is the OverdrivePedal PCB?

It measures 117.8 × 152.4 mm and has 4 copper layers, 1.6 mm thick.

What parts does the OverdrivePedal use?

35 parts, built around the TL072, PTV09A-4025F-B103 and NMJ6HFD2-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the OverdrivePedal KiCad files?

From the basimallawala/OverdrivePedal repository on GitHub, at the commit this page was made from: the board is OverdrivePedal.kicad_pcb and its schematic OverdrivePedal.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the OverdrivePedal design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).