4 layers65 × 61 mm
Serberus
suddenabnormalsecrets/Serberus
Multi-headed and Multi-Protocol embedded system hacking tool.
108 partsApache-2.0
2 layers95 × 50 mm
Flick
aswild/flickOpen source end-to-end latency testing
- Size
- 95 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 49
- Nets
- 35
- Pads
- 187
- Tracks, vias
- 352, 65
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Nov 2021
- Updated
- 15 Aug 2025
Overview
Flick is an open-source printed circuit board by aswild, from the aswild/flick repository on GitHub. It is a 2-layer board of 95 × 50 mm with 49 parts on 35 nets, routed with 352 tracks and 65 vias.
It is built around the ATSAMD21G18A-AU and AP7365-33WG. Its parts include 15 capacitors, 7 resistors, 4 crystals, 2 ICs and 2 switches. It belongs with the SAM D and SAM boards of this library.
Main components
2
ATSAMD21G18A-AU
TQFP-48-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
AP7365-33WG
SOT-25-40℃~+85℃@(Ta) 1 3.3V 300uA 400mV@(600mA) 600mA 65dB@(1kHz) 6V Fixed Over Current Protection、Over Temperature Protection、Enable、Short Circuit Protection Positive SOT-25 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C8, C11 |
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C7, C12, C13 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C6, C14, C15 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_5mm_Pad | H1, H2, H3, H4 |
| 3 | 5.1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R4 |
| 2 | 10K | Wild:Potentiometer_Bourns_PTV09A-1_Single_Vertical | VR1, VR2 |
| 2 | 15pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C10 |
| 2 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R5 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 220ohm @ 100MHz | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB1 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_MicroCrystal_CC8V-T1A-2Pin_2.0x1.2mm_HandSoldering | Y1 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | 680K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | AP7365-33W | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U2 |
| 1 | ATSAMD21G18A-A | Package_QFP:TQFP-48_7x7mm_P0.5mm | U1 |
| 1 | DEBUG | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J1 |
| 1 | G*** | Wild:Logo_OSHW_Text_7mm | svg2mod |
| 1 | GND | Wild:TestPoint_THTPad_D1.6mm_Drill1.0mm | TP1 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | LOGO | Wild:PoomFace | G*** |
| 1 | LOGO | Wild:NyanCatLOL | G*** |
| 1 | Q_Photo_NPN | LED_THT:LED_D5.0mm | Q1 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_PTS645 | SW2 |
| 1 | Rotary_Encoder_Switch | Wild:RotaryEncoder_Bourns_PEC11L-Switch_Vertical_H20mm | SW1 |
| 1 | SH1106G | Wild:GCT_FFC2B28-16_1x16-1MP_P0.5mm_Horizontal | X2 |
| 1 | SH1106G_Screen | Wild:SH1106G_SCREEN | X3 |
| 1 | THRSH | Wild:TestPoint_THTPad_D1.6mm_Drill1.0mm | TP4 |
| 1 | USB_C_2.0 | Wild:USB_C_Receptacle_GCT_USB4105 | X1 |
| 1 | VAL | Wild:TestPoint_THTPad_D1.6mm_Drill1.0mm | TP5 |
| 1 | VCC | Wild:TestPoint_THTPad_D1.6mm_Drill1.0mm | TP2 |
| 1 | VCCA | Wild:TestPoint_THTPad_D1.6mm_Drill1.0mm | TP3 |
Questions
How big is the Flick PCB?
It measures 95 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Flick use?
49 parts, built around the ATSAMD21G18A-AU and AP7365-33WG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flick KiCad files?
From the aswild/flick repository on GitHub, at the commit this page was made from: the board is pcb/flick.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flick design in my own project?
Its repository states no licence, so its author keeps all rights: ask aswild before reusing the design.
Similar boards
- 2 layers25.4 × 55.8 mm
- 4 layers70.8 × 108 mm
- 2 layers36 × 20 mm
- 4 layers35.1 × 76.3 mm
Tiny4FSK
New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker
90 parts96CERN-OHL-W-2.0 - 4 layers36.6 × 60.3 mm
StratoSoar MK3.0
crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone
85 parts43 - 4 layers42 × 83.9 mm
StratoSoar MK2.2
crnicholson/StratoSoar-MK2
StratoSoar is an engineering project that aims to be able to fly a glider (dropped from a high-altitude balloon), down to any selected coordinates.
116 parts24 - 2 layers69.8 × 40.4 mm
T Piece Kicad
calebmarting/os2026-badge
Schematics and firmware for the Open Sauce 2026 Badge and SAOs
82 parts23MIT