2 layers101.6 × 147.3 mm
Karabas pro revER
andykarpov/karabas-pro
FPGA based retrocomputer with FDD and HDD controllers
223 parts37MIT
2 layers26.4 × 17.3 mm
Knock homekit v1
andrewngai/HomekitKnock17This repo is the resources for the project on https://youtu.be/X5OxuFtGn0
- Size
- 26.4 × 17.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 12
- Nets
- 28
- Pads
- 55
- Tracks, vias
- 79, 6
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 10 Feb 2021
- Updated
- 17 Feb 2021
Overview
Knock homekit v1 is an open-source printed circuit board by andrewngai, from the andrewngai/HomekitKnock repository on GitHub. It is a 2-layer board of 26.4 × 17.3 mm with 12 parts on 28 nets, routed with 79 tracks and 6 vias.
It is built around the ESP-12E and AMS1117-3.3. Its parts include 3 resistors and 1 connector. It belongs with the ESP8266 boards of this library.
Main components
2
ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi Modules
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdHomekitKnock
This repo is the resources for the project on https://youtu.be/X5Ox_uFtGn0
this device takes certain patterns of knocking and turns them into homekit triggers which you can program to automate other accessories
3D printed case: https://www.thingiverse.com/thing:4758245
Parts
12| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | AMS1117-3.3 |
| 1 | ESP-12E | ESP8266:ESP-12E_SMD | ESP12 |
| 1 | Program | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Sensor | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | Sensor |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | MicroUSB |
The 8 most common of 12 parts.
Similar boards
- 2 layers68.5 × 53.3 mm
Iot wifi uno hw
iotmakervn/iot-wifi-uno-hw
Open hardware ESP8266 Uno board - Internet Of Things WiFi Uno
56 parts26 - 2 layers
Smol boy V1
BogdanTheGeek/ESP_RC
An Open-Source Transmitter/Receiver for RC Planes, Cars, Boats and more based on ESP-NOW
21 parts16BSD-2-Clause - 2 layers51 × 43 mm
Egg timer
MakersFunDuck/Common-Kitchen-Timer-With-LCD-Replacement-Board
A replacement PCB board for common 4 digit 7 segment LCD kitchen timers.
25 parts13GPL-3.0 - 4 layers29.9 × 32 mm
Models heart rev1.1
KushlaVR/models-heart
Можливості: Керування через WIFI з телефона або ПК 5 незалежних каналів (світлодіоди/сервомотори) 1 Н-міст для підключення мотора (піковий струм до 3А) Вмонтована BMS 1S та контроллер заряду Li-Ion акумулятора з…
106 parts7GPL-3.0 - 2 layers16.3 × 110.2 mm
ESP12E Smart Coaster
atom-robotics-lab/ThermoGlow-Coaster
This project is an ESP12E based Temperature Controlled Smart Coaster. The project uses the following: ESP12E Module 12 x WS2812B SMD LEDs MLX90614 Temperature Sensor I2C Module Power Bank Charge-Boost Module for…
50 parts5 - 2 layers56.3 × 32 mm
ESP12-E breakout board
cyberstormdotmu/ESP12E-breakout
A simple and open source ESP12E/ ESP8266 breakout board. You will need an external programmer to program the module but most of the components required to run the module are present. Made with KiCad.
18 parts3 - 2 layers41 × 28 mm
Aquarea
slqa/aquarea_esphome
I used hardware serial on pins GPIO15/GPIO13 and one pin for RTS from a GPIO5 Mini ESP board. In a 'normal' situation, the ESP12E only listens to communication between the remote and the heat pump, so you can have…
30 parts3
Questions
How big is the Knock homekit v1 PCB?
It measures 26.4 × 17.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Knock homekit v1 use?
12 parts, built around the ESP-12E and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Knock homekit v1 KiCad files?
From the andrewngai/HomekitKnock repository on GitHub, at the commit this page was made from: the board is PCB/knock_homekit_v1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Knock homekit v1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask andrewngai before reusing the design.