Skip to the content
2 layers27.8 × 32 mmBlinker01, the printed circuit board in 3D

a little kicad learning project

Size
27.8 × 32 mm
Copper layers
2
Thickness
1.6 mm
Parts
32
Nets
22
Pads
69
Tracks, vias
244, 23
Pours
5
Routed
Yes
KiCad
KiCad 4
Created
4 Sep 2017
Updated
24 Nov 2017

Overview

Blinker01 is an open-source printed circuit board by andijcr, from the andijcr/smallblinker repository on GitHub. It is a 2-layer board of 27.8 × 32 mm with 32 parts on 22 nets, routed with 244 tracks and 23 vias.

It is built around the ATTINY85V-10SU, NTR4003NT3G-JSM and ASMB-MTB0-0A3A2. Its parts include 11 resistors, 4 transistors, 2 inductors, 1 capacitor and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

3

Parts

32
QtyValueFootprintReferences
8TEST_1PWire_Pads:SolderWirePad_single_0-8mmDrill-, +, B0, bz3, G1, R4, rst5, t2
482RResistors_SMD:R_0805_HandSolderingR1, R2, R3, R8
4NTR4003NT3GTO_SOT_Packages_SMD:SOT-23_HandsolderingQ1, Q2, Q3, Q4
234RResistors_SMD:R_0805_HandSolderingR5, R6
2ASMB-MTB0-0A3A2ASMB-MTB0-0A3A2:ASMB-MTB0-0A3A2L1, L2
1100nfCapacitors_SMD:C_0805_HandSolderingC1
110KResistors_SMD:R_0805_HandSolderingR9
110RResistors_SMD:R_0805_HandSolderingR7
120KResistors_SMD:R_0805_HandSolderingR11
127RResistors_SMD:R_0805_HandSolderingR10
150RResistors_SMD:R_0805_HandSolderingR4
1ATTINY85V-10SUHousings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mmmcu
1D_ZenerDiodes_SMD:D_SC-80_HandSolderingD1
1LOGOblinker_attiny85:testfotoG***
1Magnetic Buzzerbzel-t72-0505:t72-0505BZ1
1TOUCH_PAD_COPPERSMD_Packages:1Pinclick

The 31 most common of 32 parts.

More from andijcr/smallblinker

1
  • 2 layers30.3 × 33 mmBlinker, the printed circuit board in 3D

    Blinker

    andijcr/smallblinker

    a little kicad learning project

    35 parts

Similar boards

  • 2 layers64 × 50 mmResol VBus RevE, the printed circuit board in 3D

    Resol VBus RevE

    labodj/resol-vbus-interface

    Isolated RESOL VBus RX/TX interface for ESPHome: KiCad Rev E prototype, BOM and fabrication files

    51 parts
  • 4 layers60 × 95 mmSTM32H7 GuitarPedal, the printed circuit board in 3D

    STM32H7 GuitarPedal

    GuitarML/GuitarPedalSTM32

    Guitar pedal using a stm32h7 microcontroller programmed with CubeIDE (PCB and Firmware)

    101 parts100MIT
  • 2 layers50 × 47.1 mmVectrex cartridge short, the printed circuit board in 3D

    Vectrex cartridge short

    technobly/vectrex-cartridge

    Vectrex Cartridge PCB reference design

    31 parts24
  • 4 layers36.5 × 94.1 mmNova, the printed circuit board in 3D

    Nova

    ERFSEDS/novafc-hardware

    89 parts2
  • 4 layers49.8 × 41.8 mmCc1352-swim thermo, the printed circuit board in 3D

    Cc1352-swim thermo

    mik4el/cc1352-swim-thermo

    Software and hardware for dual band radio high accuracy swim thermometer

    55 parts2Apache-2.0
  • 4 layers68.6 × 88.9 mmAdacus, the printed circuit board in 3D

    Adacus

    AoToS/Adacus

    Mixed signal PCB with op-amps, filters, ADC/DAC interfaces. ADACUS

    115 parts1
  • 2 layers48.3 × 43.2 mmBlackbox ng, the printed circuit board in 3D

    Blackbox ng

    calstar/blackbox-ng

    Blackbox Next Generation

    62 parts1BSD-3-Clause
  • 2 layersNanosaur NX shield, the printed circuit board in 3D

    Nanosaur NX shield

    rnanosaur/nanosaur-NX-shield

    🦸 A nanosaur NX, need a super shield. The Nanosaur NX shield is here!

    28 parts1

Questions

How big is the Blinker01 PCB?

It measures 27.8 × 32 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Blinker01 use?

32 parts, built around the ATTINY85V-10SU, NTR4003NT3G-JSM and ASMB-MTB0-0A3A2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Blinker01 KiCad files?

From the andijcr/smallblinker repository on GitHub, at the commit this page was made from: the board is blinker01.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Blinker01 design in my own project?

Its repository states no licence, so its author keeps all rights: ask andijcr before reusing the design.