
Power Control Circuit
ambadran/spot-welder
Battery Spot Welder Circuit Using Capactive Discharge (CD) Circuit

Battery Spot Welder Circuit Using Capactive Discharge (CD) Circuit
Power Control Circuit is an open-source printed circuit board by ambadran, from the ambadran/spot-welder repository on GitHub. It is a 2-layer board of 116.9 × 37.5 mm with 41 parts on 34 nets, routed with 304 tracks and 0 vias.
It is built around the IRF1405, S8050 and S8550. Its parts include 11 resistors, 9 transistors, 2 ICs and 1 capacitor. It belongs with the PIC boards of this library.
Battery Spot Welder Circuit Using Capactive Discharge (CD) Circuit
Using PIC16F628A and 16x2 display, a user-friendly interface is implemented
Three lines of capacitors (six in series) circuit act as the capacitor bank for HIGH current discharge. They total to a <> Coloumbs. They have an equivilant series resistance of <> milli-ohms This means that at 24v they can deliver <> Amps!!!
Four VERY HIGH Power MOSFETs IRF3205 are put in parallel, capable of withstanding <> Amps through them
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Pin | MountingHole:MountingHole_4.3mm_M4_Pad | +12v1, 12v_GND1, CAP-1, Cap+1, Electrode-1, Electrode+1 |
| 5 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4, R6, R8, R10 |
| 5 | IRF1405 | Package_TO_SOT_THT:TO-220-3_Vertical | Q4, Q8, Q9, Q10, Q12 |
| 4 | JST-2P | Connector_JST:JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | ARROW1, ENTER1, Power5v1, WELD1 |
| 3 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7, R9, R11 |
| 3 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottom | H1, H2, H3 |
| 2 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3 |
| 2 | PC817 | Package_DIP:DIP-4_W7.62mm | U1, U2 |
| 2 | S8050 | Package_TO_SOT_THT:TO-92_Inline_Wide | Q2, Q6 |
| 2 | S8550 | Package_TO_SOT_THT:TO-92_Inline_Wide | Q3, Q7 |
| 1 | 0ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P5.08mm_Vertical | Bridge1 |
| 1 | 220uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 2ohm | Resistor_THT:R_Axial_Power_L25.0mm_W9.0mm_P27.94mm | R-Shunt1 |
| 1 | 330 | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R14 |
| 1 | 5kOhm | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | Trimmer1 |
| 1 | PIC16F628A-IP | Package_DIP:DIP-18_W7.62mm_LongPads | Main-MCU1 |
| 1 | WC1602A | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | DS1 |

ambadran/spot-welder
Battery Spot Welder Circuit Using Capactive Discharge (CD) Circuit

JIMS-Innovations/BLDCM-ESC
This repository contains the firmware, design files and documents for a Sensorless Electronic Speed Controller (for brushless DC motors) developed by Jesutofunmi Kupoluyi.

KaeptnBalu/Arduino_Spot_Welder_V2
Arduino controlled Spot Welder for battery welding

twam/IEC-62056-21-Optical-Probe
Optical-Probe for reading out power meters supporting IEC 62056-21 via USB


xDuinoRails/xDuinoRails_Hermes-M
Your DCC/Railcom signals and a +5V power source for your microcontroller on a breadboard

xDuinoRails/xDuinoRails_Thor
Make a Seeed XIAO board a mtc21 decoder, all the electronics needed is on this little board: - mtc21/plux16 compatible connector - DC Motor - 2x Functions - DCC / DCC-ACK / RailCom

ambadran/Revolute_Joint
Optimal Cheap Robotic Actuator allowing high Torque and moderate Speed. Allow PRECISE Absolute, Speed and Torque Control. Using 3D-printed Cycloidal Drive, Custom PCB and LQR Control Algorithm.

chatelao/xDuinoRail-Decoder
The friendly decoder development plattform for model railroad tinkers.
It measures 116.9 × 37.5 mm and has 2 copper layers, 1.6 mm thick.
41 parts, built around the IRF1405, S8050 and S8550. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ambadran/spot-welder repository on GitHub, at the commit this page was made from: the board is Circuits/power_control_circuit_V2/final_version/Power Control Circuit.kicad_pcb and its schematic Circuits/power_control_circuit_V1/Power Control Circuit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ambadran before reusing the design.