
Hub16
joshajohnson/Hub16
A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

practice 01 of tutorial https://github.com/ruiqimao/keyboard-pcb-guide
Example-20210328 is an open-source printed circuit board by alexkander, from the alexkander/practice-keyboard-pcb-guide-01 repository on GitHub, published under the MIT licence. It is a 2-layer board of 82.6 × 58.4 mm with 34 parts on 47 nets, routed with 194 tracks and 22 vias.
It is built around the ATMEGA32U4. Its parts include 10 switches, 9 diodes, 8 capacitors, 4 resistors and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.
practice-keyboard-pcb-guide-01
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | D | Diode_SMD:D_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D8, D9 |
| 9 | KEYSW | keebs:Mx_Alps_100 | K1, K2, K3, K4, K5, K6, K7, K8, K9 |
| 4 | 0.1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C5, C6 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | 22 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7 |
| 1 | ATMEGA32U4 | Package_QFP:TQFP-44_10x10mm_P0.8mm | U1 |
| 1 | RESET_PUSH | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | USB_mini_micro_B | keyboard_parts:USB_miniB_hirose_5S8 | J1 |
| 1 | XTAL_GND | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | X1 |

joshajohnson/Hub16
A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

tmk/USB2USB_Converter
USB to USB keyboard protocol converter supported by TMK keyboard firmware



evyd13/gh80-series
GH80-1800, GH80-3700 and GH80-3003 by Evy (aka anykeys.eu)



It measures 82.6 × 58.4 mm and has 2 copper layers, 1.6 mm thick.
34 parts, built around the ATMEGA32U4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the alexkander/practice-keyboard-pcb-guide-01 repository on GitHub, at the commit this page was made from: the board is example-20210328.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).