
REIN R1
rein-baremetal/REIN_R1_KiCad
Dual-MCU baremetal embedded development board featuring high-speed QSPI storage, hardware USB hub, and flexible power management. Open for PCB trace routing collaboration

Minisumo 2025 is an open-source printed circuit board by alexivan04, from the alexivan04/Minisumo-PCB repository on GitHub. It is a 4-layer board of 34 × 86 mm with 109 parts on 104 nets, routed with 617 tracks and 346 vias.
It is built around the ESP32-S3-WROOM-1-N8, MC33926PNB and TLV75733PDBVR-MS, with the TXS0108EPWR, USBLC6-2P6 and SI2371EDS among its other parts. Its parts include 38 capacitors, 28 resistors, 16 diodes, 8 connectors and 7 ICs. It belongs with the ESP32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C3, C11, C12, C16, C17, C18, C21, C23, C25, C26, C27, C28, C29, C30, C34 +4 |
| 12 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R6, R7, R8, R13, R14, R15, R16, R17, R18, R19, R25 |
| 8 | LED_Small | LED_SMD:LED_0603_1608Metric | D10, D11, D12, D13, D14, D15, D17, D18 |
| 7 | 3k3 | Resistor_SMD:R_0603_1608Metric | R20, R26, R27, R28, R29, R31, R32 |
| 4 | 1.95Vf, 20mA, RED | LED_SMD:LED_0603_1608Metric | D2, D7, D8, D9 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C2, C14, C15, C33 |
| 4 | 47uF | Capacitor_SMD:C_1210_3225Metric | C8, C9, C10, C31 |
| 3 | 1uF | Capacitor_SMD:C_0603_1608Metric | C13, C32, C36 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R4, R33 |
| 2 | 100uF - low ESR | Capacitor_THT:C_Radial_D6.3mm_H11.0mm_P2.50mm | C22, C24 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R21, R23 |
| 2 | 2k | Resistor_SMD:R_0603_1608Metric | R22, R24 |
| 2 | 33nF | Capacitor_SMD:C_0603_1608Metric | C19, C20 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2, J7 |
| 2 | MC33926PNB | footprints:QFN80P800X800X220-33N | U6, U7 |
| 1 | 10V | Diode_SMD:D_SOD-123F | D4 |
| 1 | 10uF | Capacitor_SMD:C_1210_3225Metric | C4 |
| 1 | 220nF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 24k9 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C35 |
| 1 | 6.2V | Diode_SMD:D_SOD-123F | D6 |
| 1 | 8.2V | Diode_SMD:D_SOD-123F | D5 |
| 1 | 8.2uH, 21mOhm | footprints:INDPM7166X300N | L1 |
| 1 | BATT_IN | Connector_AMASS:AMASS_XT30U-F_1x02_P5.0mm_Vertical | J6 |
| 1 | BOOT | footprints:435441019830 | SW3 |
| 1 | CASE | footprints:435441019830 | SW2 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | D_Schottky_Small | Diode_SMD:D_SOD-123 | D3 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1U | U3 |
| 1 | FerriteBead_Small | Capacitor_SMD:C_0805_2012Metric | FB1 |
| 1 | GPIO13 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP1 |
| 1 | GPIO17 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP13 |
| 1 | GPIO35 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP8 |
| 1 | GPIO36 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP9 |
| 1 | GPIO37 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP12 |
| 1 | GPIO7 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP11 |
| 1 | LMR33630ADDAR | footprints:DDA0008J | U1 |
| 1 | MOTOR1 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | MOTOR2 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | RESET | footprints:435441019830 | SW1 |
| 1 | START_MODULE | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | Si2371EDS | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | TLV75733PDBVR | footprints:DBV0005A_N | U4 |
| 1 | TXS0108EPWR | footprints:SOP65P640X120-20N | U5 |
| 1 | USBLC6-2P6 | Package_TO_SOT_SMD:SOT-666 | U2 |
| 1 | USB_C Connector | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |

rein-baremetal/REIN_R1_KiCad
Dual-MCU baremetal embedded development board featuring high-speed QSPI storage, hardware USB hub, and flexible power management. Open for PCB trace routing collaboration

Ekta-Gupta27/custom-flight-controller-pcb
Custom flight controller PCB designed in KiCad with STM32F7, multiple sensors, CAN, USB, telemetry, PWM and IO interfaces.



Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)



abhisek-mahapatro-RD/4-Channel-motor-driver-with-reverse-polarity-protection
A robust 4-channel brushed DC motor driver PCB based on the DRV8871 IC, featuring integrated reverse polarity protection and hardware current limiting for robotics and automation applications.
It measures 34 × 86 mm and has 4 copper layers, 1.6 mm thick.
109 parts, built around the ESP32-S3-WROOM-1-N8, MC33926PNB, TLV75733PDBVR-MS and TXS0108EPWR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the alexivan04/Minisumo-PCB repository on GitHub, at the commit this page was made from: the board is minisumo_2025.kicad_pcb and its schematic drivers.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask alexivan04 before reusing the design.