Skip to the content
2 layers24.1 × 77.5 mmModule generic top board, the printed circuit board in 3D

Module generic top board

alexdrymonitis/3dPd31

Digital modular hardware/software synthesizer project based on Pure Data and Arduino

Size
24.1 × 77.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
16
Nets
39
Pads
107
Tracks, vias
237, 7
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
11 Aug 2016
Updated
3 May 2018

Overview

Module generic top board is an open-source printed circuit board by alexdrymonitis, from the alexdrymonitis/3dPd repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 24.1 × 77.5 mm with 16 parts on 39 nets, routed with 237 tracks and 7 vias.

It is built around the 74HC165D and 74HC595. Its parts include 8 connectors, 3 capacitors, 3 ICs and 1 resistor. It belongs with the audio and music boards of this library.

Main components

2

README

README.md

3dPd

This repository hosts the code, schematics, and circuit board designs made in Kicad, for a hardware digital modular synthesizer. The audio is programmed in Pure Data and the hardware control in the Arduino language. This synthesizer is supposed to run on a Raspberry Pi 3 and a Teensy3.2. You're welcome to use any other hardware you like, but this specific hardware is supported and explained here.

Note about the Arduino code

Go to the Arduino_code directory and read the README.txt file first. That should give you enough information about the Arduino code. Do that before you start reading the Pd patches.

Note about the Pd patches

The heart of this project is the modular_synthesizer.pd patch. Open it and you'll see some other abstractions in there. Go into the [pd modules] sub-patch and look inside. Each module must have its own abstraction. There are some tutorial module abstractions which show you how to build your own. Open them and read them carefully.

There's also a debug.pd patch which helps with debugging by showing input from the Teensy and printing various message concerning module connections and LED states.

Dependencies

This project uses the following external libraries:
zexy
comport
iemmatrix
iemguts
ggee
list-abs
tabreceive_mult~

The first five libraries are being installed with "apt-get" and the last two are installed through Deken (In Pd got to Help -> Find externals and type these two names -one at a time-, the highlighted version(s) is good for your system).

Pd-0.47.0 or higher is required.

General note

I'll upload a wiki with instructions for creating the hardware of a module and the whole system. It's in my TODO list, which will hopefully happen in the near future. You can watch a demo video of the synthesizer here https://www.youtube.com/watch?v=HD13bDPyBWA

Parts

16
QtyValueFootprintReferences
30.1uFCapacitors_ThroughHole:C_Disc_D3_P2.5C1, C2, C3
3CONN_01X08Pin_Headers:Pin_Header_Straight_1x08P1, P2, P4
2CONN_01X01drillhole:holeP7, P8
110KResistors_THT:R_Array_SIP9RN1
110KDiscret:R1R1
14051Housings_DIP:DIP-16_W7.62mm_LongPadsU1
174HC165Housings_DIP:DIP-16_W7.62mm_LongPadsU3
174HC595Housings_DIP:DIP-16_W7.62mm_LongPadsU2
1CONN_01X02Pin_Headers:Pin_Header_Straight_1x02P5
1CONN_01X03Connectors_JST_PH:Connectors_JST_B3B-PH-KP3
1CONN_01X11Pin_Headers:Pin_Header_Straight_1x11P6

More from alexdrymonitis/3dPd

5
  • 2 layers105.4 × 57.2 mmPower bus, the printed circuit board in 3D

    Power bus

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    25 parts31GPL-3.0
  • 2 layers26.7 × 90.8 mmModule specific board2, the printed circuit board in 3D

    Module specific board2

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    18 parts31GPL-3.0
  • 2 layers64.8 × 45.7 mmTeensy mother board, the printed circuit board in 3D

    Teensy mother board

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    13 parts31GPL-3.0
  • 2 layers73.7 × 39.4 mmPower distributor, the printed circuit board in 3D

    Power distributor

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    12 parts31GPL-3.0
  • 2 layers24.1 × 77.5 mmModule generic bottom board, the printed circuit board in 3D

    Module generic bottom board

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    7 parts31GPL-3.0

Similar boards

  • 2 layers245.1 × 160 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-64x4-Home-Computer

    My DIY TTL home computer with VGA and PS/2 and 4x the processing power of a Commodore C64 or Apple II.

    139 parts326
  • 2 layers171.5 × 106.7 mmSequencer, the printed circuit board in 3D

    Sequencer

    westlicht/performer-hardware

    PER|FORMER Eurorack Sequencer - Hardware Design Files

    435 parts110
  • 2 layers306.1 × 130.2 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-64-Home-Computer

    Legacy: Full TTL-only home computer with VGA and PS/2 and twice the processing power of a Commodore 64

    132 parts94
  • 2 layers208.9 × 170.8 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-UART-Computer-3

    Version 3 of my educational DIY TTL computer built around a UART serial interface - now with blinkenlights!

    207 parts54
  • 2 layers148.8 × 132.2 mmUsbflashprog, the printed circuit board in 3D

    Usbflashprog

    robsonsmartins/usbflashprog

    A memory device programmer (Flash/EPROM/E2PROM) board and software, connected to PC by USB port.

    125 parts36
  • 4 layers120 × 100 mmBsc, the printed circuit board in 3D

    Bsc

    shining-man/bsc_hw

    Hardware battery safety controller (BSC)

    286 parts31MIT
  • 2 layers56 × 110 mmTrs pcb, the printed circuit board in 3D

    Trs pcb

    Windfisch/midikraken

    A open source, open hardware up-to-16x USB-MIDI-interface for around 15 bucks in its smallest configuration.

    125 parts28

Questions

How big is the Module generic top board PCB?

It measures 24.1 × 77.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Module generic top board use?

16 parts, built around the 74HC165D and 74HC595. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Module generic top board KiCad files?

From the alexdrymonitis/3dPd repository on GitHub, at the commit this page was made from: the board is circuits/module_generic_top_board/module_generic_top_board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Module generic top board design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).