
Mora villogo
kissadamfkut/mora_blinker
Simple LED blinker with ATtiny13A for educational purposes

A simple development board with an LED and GPIOs on Pin header, includes also ISP Header, Power supply with screw terminal
Attiny13A Devboard v1 SMD is an open-source printed circuit board by alexanderjg85, from the alexanderjg85/simple_attiny13a_devboard repository on GitHub, published under the MIT licence. It is a 2-layer board of 48 × 24 mm with 20 parts on 10 nets, routed with 122 tracks and 19 vias.
It is built around the ATTINY13A-SSU and SS14. Its parts include 3 connectors, 2 capacitors, 2 resistors, 2 diodes and 1 IC. It belongs with the microcontroller boards boards and the AVR (ATmega, ATtiny) boards of this library.
A simple development board with an LED and GPIOs on Pin header, includes also ISP Header, Power supply with screw terminal.
This project is dual-licensed / Dieses Projekt ist dual-lizenziert:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 10 uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 100 nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 1 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
| 1 | 470 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 5V | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | ATtiny13A-SS | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | LED | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | MISO | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | MOSI | TestPoint:TestPoint_Pad_D1.5mm | TP8 |
| 1 | PB3 | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | RED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | RST | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | SCK | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | SS14 | Diode_SMD:D_SMA_Handsoldering | D1 |
| 1 | SW_RESET | AJ_Electromechanical:SW_SPST_PTS647_Sx38_Handsolder | SW1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | VCC | TestPoint:TestPoint_Pad_D1.5mm | TP3 |

kissadamfkut/mora_blinker
Simple LED blinker with ATtiny13A for educational purposes

dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere

ep092/TX5823
FPV Sender mit Kanalwahl und konfiguration über SPI. Integriertes OSD mit MAX7456 und Spannungswandlern für 5V, 3,3V und 12V über einen Eingangsspannungsbereich von 8V bis 25.2V.





Alksndr55/mesh-repeater
Mesh Repeater v1 — одноплатный LoRa-репитер для MeshCore и Meshtastic, 90×100 мм. Упор на максимальное энергосбережение и работу в суровых сибирских зимах. Солнечный зарядник, Na-ion 1S / LTO 2S.
It measures 48 × 24 mm and has 2 copper layers, 1.6 mm thick.
20 parts, built around the ATTINY13A-SSU and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the alexanderjg85/simple_attiny13a_devboard repository on GitHub, at the commit this page was made from: the board is Hardware/Attiny13A_Devboard_v1_SMD/Attiny13A_Devboard_v1_SMD.kicad_pcb and its schematic Hardware/Attiny13A_Devboard_v1_SMD/Attiny13A_Devboard_v1_SMD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).