

ECE445L Lab7
My final mechatronics project from the Spring 2025 Embedded Systems Design Lab course. Taught by Dr. Jonathan Valvano. Team was Aidan Aalund, Alexa Aguilar Izquierdo, Paul Schnoebelen, Eric Zang, and Brian Ahn.
- Size
- 114.4 × 88.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 79
- Pads
- 216
- Tracks, vias
- 653, 133
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 25 Oct 2025
- Updated
- 30 Apr 2026
Overview
ECE445L Lab7 is an open-source printed circuit board by aidanaalund, from the aidanaalund/ece-445l-final-project repository on GitHub. It is a 2-layer board of 114.4 × 88.9 mm with 56 parts on 79 nets, routed with 653 tracks and 133 vias.
It is built around the TM4C123GH6PMIR, HC-SR04 and IRLD024PBF, with the ABM3-16.000MHZ-B2-T among its other parts. Its parts include 17 capacitors, 8 connectors, 7 resistors, 6 ICs and 4 diodes.
Main components
4TM4C123GH6PMIR
LQFP-64(10x10)-40℃~+85℃ 1.08V~3.63V 12bit 256KB 2KB 32 Bit 32KB 43 80MHz ARM Cortex-M4F Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSTexas InstrumentsMicrocontrollers (MCU/MPU/SOC)HC-SR04
-- Ultrasonic Receivers, Transmitters ROHSUniversal MicroelectronicsUltrasonic Receivers, TransmittersIRLD024PBF
HVMDIP-4-55℃~+175℃ 1 N-channel 1.3W 140mΩ@4V 18nC@5V 2.5A 2V 360pF 53pF 60V 870pF N-Channel ±10V HVMDIP-4 MOSFETs ROHSVishay IntertechnologyMOSFETsABM3-16.000MHZ-B2-T
SMD5032-2P-20℃~+70℃ 16MHz 18pF 40Ω Crystal Oscillator ±20ppm ±50ppm SMD5032-2P Crystals ROHSAbraconCrystals
README
README.mdECE 445L Final Project
This final project is titled 'Magic Wand'. The user's hand is tracked with a sensor and the fans in the tubes will make a ping pong ball float to match the user's hand distance. Won professor's vote at the Spring 2025 Embedded Systems competition.
0 Repository Structure
The typical explanation for the repo structure. Lab specific instructions can be found further below.
0.1 HW
The hw folder should contain your schematic and board files for your PCB or
circuits. In labs 1-5 and 10, you will be creating schematics for your circuit
in KiCad.
0.2 SW
The sw folder should contain your application firmware and software written
for the lab. The sw/inc folder contains firmware drivers written for you by
Professor Valvano. Feel free to write your own (in fact, in some labs, you may
be required to write your own).
You can place any other source files in the sw folder. TAs will look at the
files you create and/or modify for software quality and for running your
project.
0.3 Resources
A couple files are provided in the Resources folder so you don't have to keep searching for that one TI document. Some of them are immediately useful, like the TM4C datasheet. Others may be useful for your final project, like the TM4C_System_Design_Guidelines page.
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | ECE445L:C_Axial_200mil | C4, C6, C7, C8, C17 |
| 5 | 4.7uF | ECE445L:CP_Radial_Tantal200mil | C12, C13, C14, C15, C16 |
| 4 | ~ | ECE445L:MountingHole_4_40 | H1, H2, H3, H4 |
| 3 | 10k | ECE445L:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2, R3, R7 |
| 3 | HC-SR04 | ECE 445L:PinHeader_1x04_P2.54mm_Vertical | U4, U5, U7 |
| 2 | 0.01uF | ECE445L:C_Axial_200mil | C5, C11 |
| 2 | 10pF C0G | ECE445L:C_Axial_200mil | C1, C2 |
| 2 | 1V0 | 1N914:AFL-W2C8.9D | D1, D4 |
| 2 | 1uF | ECE445L:C_Axial_200mil | C3, C9 |
| 2 | IRLD024PBF | ECE445L:DIP920W60P254L490H457Q4N | Q1, Q2 |
| 2 | LED | ECE445L:LED_D5.0mm | D2, D3 |
| 1 | +3.3V | ECE445L:Testpoint_1x02_P2.54mm | TP3 |
| 1 | +5V | ECE445L:Testpoint_1x02_P2.54mm | TP1 |
| 1 | 1M | ECE445L:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
| 1 | 1k | ECE445L:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R4 |
| 1 | 2.2uF | ECE445L:CP_Radial_Tantal200mil | C10 |
| 1 | 330 | ECE445L:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5 |
| 1 | 820 | ECE445L:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R6 |
| 1 | ABM3-16.000MHZ-B2-T | ECE445L:ABM3 | Y1 |
| 1 | Adafruit ST7735R | ECE445L:adafruit_st7735r2 | U2 |
| 1 | Fan1 | ECE445L:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Fan2 | ECE445L:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Fans | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | GND | ECE445L:Testpoint_1x02_P2.54mm | TP2 |
| 1 | JTAG | ECE445L:PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | LM2937ET-3.3_NOPB | ECE445L:TO254P470X1028X1955-3P | IC1 |
| 1 | LOGO | ECE 445L:Wand | G*** |
| 1 | Logic | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J4 |
| 1 | Mode | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | On/Off | ECE445L:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | PF2 | ECE445L:Testpoint_1x02_P2.54mm | TP4 |
| 1 | Reset | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | TM4C123GH6PMIR | ECE445L:QFP50P1200X1200X160-64N | U1 |
| 1 | USBC | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J8 |
| 1 | USBCFAN | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J9 |
Similar boards
- 2 layers139.4 × 62.7 mm

- 2 layers150 × 90 mm

ECE445L Lab7Restart
Andres-Wearden/Lab10
The typical explanation for the repo structure. Lab specific instructions can be found further below.
87 parts - 2 layers132 × 78 mm

ECE445L Lab7
AndrewYin04/VR-Goggles-Embedded-Lab
The typical explanation for the repo structure. Lab specific instructions can be found further below.
124 parts - 2 layers134 × 58.5 mm

ECE445L Lab6
chengkun-yang/ece-445l-lab-6-chengkun-yang
The typical explanation for the repo structure. Lab specific instructions can be found further below.
48 parts - 2 layers103.5 × 35.7 mm

Controller PCB
jAnAnIshreee/Just-Dance-
A from-scratch reimagining of the Wii game "Just Dance": custom motion controller hardware (TM4C ARM Cortex-M4, SPI IMU, DAC audio) running on-device ML for real-time dance recognition, with MQTT syncing multiple…
40 parts - 2 layers114.4 × 88.9 mm

Lab6
Jesus61302/ECE445L-Lab1-jh69848
IMPORTANT (for those not using Github Classroom): To clone this repository, click the green "Use this template" button and create a PRIVATE repository.
32 parts - 2 layers86.4 × 61 mm

Cjh4858 gam3769 project
K0-p/Garfield-Wheel
HID-compliant game controller with embedded button mapping firmware and gyroscope controls
40 parts - 2 layers152 × 110.6 mm

Baseline project
maanavkoladia/DigiPiano
The DigiPiano is a velocity-sensitive digital piano designed using STM32 and ESP32 microcontrollers. It combines advanced sensor technology, high-quality audio playback, and Bluetooth connectivity to deliver a realistic…
44 parts
Questions
How big is the ECE445L Lab7 PCB?
It measures 114.4 × 88.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ECE445L Lab7 use?
56 parts, built around the TM4C123GH6PMIR, HC-SR04, IRLD024PBF and ABM3-16.000MHZ-B2-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ECE445L Lab7 KiCad files?
From the aidanaalund/ece-445l-final-project repository on GitHub, at the commit this page was made from: the board is hw/ECE445L_Lab7/ECE445L_Lab7.kicad_pcb and its schematic hw/ECE319K_Starter/ECE319K_Starter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ECE445L Lab7 design in my own project?
Its repository states no licence, so its author keeps all rights: ask aidanaalund before reusing the design.