

Gas tank temp reg PCB
Mímisbrunnr gas tank temperature control unit
- Size
- 118.9 × 56.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 76
- Pads
- 217
- Tracks, vias
- 448, 65
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 8 Nov 2022
- Updated
- 8 Jun 2023
Overview
Gas tank temp reg PCB is an open-source printed circuit board by aesirkth, from the aesirkth/Mimisbrunnr_gas_temp_ctrl repository on GitHub. It is a 2-layer board of 118.9 × 56.6 mm with 54 parts on 76 nets, routed with 448 tracks and 65 vias.
It is built around the ESP32-WROOM-32, MAX31856 and BD733L5FP-CE2, with the BC547 and SRD-12VDC-SL-C among its other parts. Its parts include 11 resistors, 10 connectors, 8 capacitors, 7 ICs and 6 diodes. It belongs with the ESP32 boards of this library.
Main components
5ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesMAX31856
UncategorisedMaxim Integrated (Analog Devices)BD733L5FP-CE2
TO-252-40℃~+125℃@(Ta) 1 3.3V 45V 500mA 63dB@(120Hz) 6uA 800mV@(200mA) Fixed Over Current Protection、Over Temperature Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSROHM SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBC547
TO-92Bipolar (BJT)Jiangsu Changjing Electronics Technology (CJ)SRD-12VDC-SL-C
插件,19.2x15.6mm100mΩ 10ms 10ms 12V 15A 250V@AC 360mW 400Ω 5 Non-Polarized - Single Coil One set changeover: 1C (SPDT - changeover) 插件,19.2x15.6mm Power Relays ROHS松乐Power Relays
README
README.mdMimisbrunnr_gas_temp_ctrl
Mímisbrunnr gas tank temperature control unit
Project hierarchy: Mjölnir → Mimisbrunnr
About
Mímisbrunnur is a temperature control unit that controls the temperature of the N2 gas tank that is used as the oxidizer for the Mjölnir rocket. The unit will regulate the temperature the desired temperature. It will measure the temperature of the tank and then turn on a pump to allow warm water to flow in a tube around the tank.
Requirements
- Regulate the temperature of the oxidizer gas tank for the Mjölnir rocket
- Manual as well as digital controls
- Manual control:
- Screen to see configurations
- Buttons to control
- Digital control:
- Connect through wifi and integrated into the system of Mjölnir
- Option to connect through CAN bus
- Manual control:
- Measure the temperature
- Have 3 temperature sensors: 1 top, 1 middle, 1 bottom
- Turn a water pump to heat the tank
- Tolerate rainy, snowy or other similar weather conditions
Optional Requirements
- Control heating element
- Fully Waterproof
Usage
Buttons to navigate
Connectors
PCB
Box
Software
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | Screw_Terminal_01x02 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J3, J4, J5, J6, J7, J8, J9 |
| 6 | 1k | Resistor_SMD:R_0805_2012Metric | R2, R3, R4, R5, R8, R9 |
| 6 | C_Small | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5, C6, C7, C8 |
| 5 | MAX31856 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U3, U4, U5, U6, U7 |
| 4 | LED | LED_SMD:LED_0805_2012Metric | D1, D2, D3, D4 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R6, R7 |
| 3 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3 |
| 3 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1, SW2, SW3 |
| 2 | 4k7 | Resistor_SMD:R_0805_2012Metric | R10, R11 |
| 2 | BC547 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2 |
| 2 | C | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | DIODE | Diode_SMD:D_0805_2012Metric | D5, D6 |
| 2 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 2 | SRD-12VDC-SL-C | SRD-12VDC-SL-C:RELAY_SRD-12VDC-SL-C | K1, K2 |
| 2 | header_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J10 |
| 1 | BD733L5FP-CE2 | BD733L5FP:BD750L5FPCE2 | U2 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | Jack-DC | Connector_AMASS:AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J2 |
Similar boards
- 4 layers188 × 90.2 mm

- 2 layers

- 2 layers100 × 100 mm

Ft150ts E
z-XOF-z/FT150TS
Tablero digital + launcher para Android que funciona solo con el teléfono del manubrio y está listo para una tarjeta ESP32 en la moto.
71 parts - 2 layers92 × 72.2 mm

- 4 layers144.2 × 82.8 mm

SmartFuseBox
k3ldar/PowerControlHub
PowerControlHub is a flexible automation controller for 12V systems. It combines relay switching, sensor monitoring, and smart‑home connectivity (MQTT, Home Assistant, REST, BLE) into one device.
93 parts5GPL-3.0 - 2 layers100 × 74 mm

Qym solder
basson/qym-solder
QymSolder - Soldering station three in one - hakko t12, hot air gun, d909/898D or analog.
135 parts4GPL-3.0 - 2 layers215 × 90 mm

Motor Board
acwright/Sherline-CNC-Conversion
Project files for my Sherline Lathe and Mill CNC conversion
46 parts1MIT - 4 layers83 × 67.5 mm

MarineBoard
Cadburies/SisuAssistant
Sailing yacht Sisu: Home Assistant + ESPHome Marine Board (alternator regulation, tanks) + MQTT kernel, Signal K/Grafana/InfluxDB on a NAS, and Sisu Nav chart & weather-routing cockpit.
162 parts1Apache-2.0
Questions
How big is the Gas tank temp reg PCB PCB?
It measures 118.9 × 56.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gas tank temp reg PCB use?
54 parts, built around the ESP32-WROOM-32, MAX31856, BD733L5FP-CE2 and BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gas tank temp reg PCB KiCad files?
From the aesirkth/Mimisbrunnr_gas_temp_ctrl repository on GitHub, at the commit this page was made from: the board is Mimisbrunnr_PCB/gas_tank_temp_reg_PCB.kicad_pcb and its schematic Mimisbrunnr_PCB/connectors.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gas tank temp reg PCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask aesirkth before reusing the design.