Skip to the content
4 layers92.3 × 99.8 mmBccc sao rp2350a, the printed circuit board in 3D

Source files for reconstructing the Beverage Chilling Contraption Contest badge, released at Defcon 2026

Size
92.3 × 99.8 mm
Copper layers
4
Thickness
1.6 mm
Parts
109
Nets
85
Pads
330
Tracks, vias
927, 138
Pours
18
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
14 Mar 2026
Updated
2 Aug 2026

Overview

Bccc sao rp2350a is an open-source printed circuit board by aerospace-venoms, from the aerospace-venoms/BCCC_Temperature_SAO repository on GitHub. It is a 4-layer board of 92.3 × 99.8 mm with 109 parts on 85 nets, routed with 927 tracks and 138 vias.

It is built around the W25Q16JVSSIQ, 74HC595D and AMS1117, with the MDD2302, PSM712-LF-T7 and SI2301CDS-T1-GE3 among its other parts. Its parts include 28 resistors, 28 diodes, 21 capacitors, 5 ICs and 5 transistors. It belongs with the lEDs and displays boards and the RP2350 boards of this library.

Main components

9

README

README.md

BCCC SAO Temperature Badge

A Simple Add-On (SAO) badge for the DEF CON Beverage Chilling Contraption Contest (BCCC). Winners of the contest receive copies of this badge, at least for this year (2026) or until I run out.

The PCB is shaped like a red solo cup with overflowing beer. It reads ambient temperature using a DS18B20 sensor and displays the result in degrees Fahrenheit on three 7-segment LED displays.

Hardware

  • MCU: Raspberry Pi RP2350A (QFN-60)
  • Flash: W25Q16 (2 MB)
  • Sensor: DS18B20 1-Wire temperature sensor (GPIO 16); falls back to the RP2350's internal die sensor if not present
  • Display: 3x common-anode 7-segment LED displays, multiplexed via a 74HC595 shift register
  • Interface: USB-C (programming and serial debug output)
  • Extras: 3-pin SWD debug header, user pushbuttons (RUN, QSPI_SS/BOOTSEL, and a brightness button on GPIO 19)

Pin Assignments

SignalGPIO
1-Wire (DS18B20)16
Digit select 1 (leftmost)8
Digit select 2 (middle)9
Digit select 3 (rightmost)10
74HC595 SER (data)11
74HC595 SRCLK (shift clock)12
74HC595 RCLK (latch clock)13
74HC595 /OE (output enable)14
74HC595 /MR (master reset)15
Brightness button (HW rev ≥ 1.3)19

Firmware

The firmware uses the Raspberry Pi Pico SDK and is structured around both RP2350 cores:

  • Core 0 — reads temperature from the DS18B20 every ~1 second and updates the display buffer
  • Core 1 — continuously time-multiplexes the three 7-segment digits at ~333 Hz

If no DS18B20 is detected on the 1-Wire bus, the display shows --- and the internal die temperature is logged to USB serial for reference.

On boards with hardware revision 1.3 or later, the brightness button (GPIO 19) cycles the display through four brightness levels.

Prerequisites

  • Raspberry Pi Pico SDK installed at /usr/src/pico-sdk (or update PICO_SDK_PATH in CMakeLists.txt)
  • CMake 3.13+
  • ARM GCC toolchain (gcc-arm-none-eabi)

On Debian/Ubuntu:

sh
sudo apt install cmake gcc-arm-none-eabi libnewlib-arm-none-eabi build-essential

Building

sh
mkdir build && cd build
cmake ..
make -j$(nproc)

This produces build/thermometer.uf2.

Flashing

Don't want to build from source? A prebuilt, versioned image is in firmware/ — handy if you need to recover a badge.

  1. Hold the BOOTSEL button (QSPI_SS) while plugging in USB-C, or press and hold QSPI_SS then press RUN to reboot into bootloader mode.
  2. The board will appear as a USB mass storage device named RP2350. (RP2040-based boards use RPI-RP2; the RP2350 reports Board-ID: RP2350.)
  3. Copy the .uf2 to the drive:
sh
cp firmware/thermometer-v1.1.0.uf2 /media/$USER/RP2350/
# or, from a source build:
cp build/thermometer.uf2 /media/$USER/RP2350/

The board reboots automatically and starts running. At boot it prints its firmware version over USB serial:

text
BCCC Temperature SAO — firmware v1.1.0 (HW rev 13)

Serial Debug Output

Connect a serial terminal at any baud rate (USB CDC ACM) to see temperature readings:

sh
screen /dev/ttyACM0
# or
minicom -D /dev/ttyACM0

Tooling

Helper scripts for building and for programming boards in quantity — see tools/README.md for full details.

ScriptPurpose
scripts/bump-firmware.shRebuild and refresh the prebuilt UF2 so its filename always matches FW_VERSION. Pass a version (1.1.0) to bump first.
tools/flash_and_test.pyWatch for boards in BOOTSEL, flash each, then verify over USB serial that the firmware runs. Handles several boards at once.
tools/soak_log.pyBurn-in logger: timestamped output per board, recording disconnects and reboots.
tools/soak_report.pySummarise a burn-in run (duration, drift, gaps, reboots) with a per-board verdict.

Programming a batch:

sh
tools/flash_and_test.py --log batch.csv

Leave it running and keep plugging boards in; Ctrl-C prints a summary. Boards with no DS18B20 fitted report PASS* rather than failing, so this works before the sensors are attached. Once they are, add --require-sensor to catch an unpopulated or badly soldered sensor.

Hardware Design

The KiCad project files are in hardware/bccc_sao_rp2350a/. The PCB artwork — a red solo cup with overflowing beer — was designed in Inkscape, starting from an AI-generated image, then transferred into KiCad using the SVG2Shenzhen plugin.

Many thanks to the KiCad project for excellent, free, open-source EDA software.

License

WTFPL v2 — do what the f*** you want with it.

Parts

109
QtyValueFootprintReferences
24LED_SmallCustom_LED_footprint:LED-SMD_L1.7-W1.1-R-RD_BULED501, D502, D503, D504, D505, D506, D507, D508, D601, D602, D603, D604, D605, D606, D607, D608 +8
10100nFPCM_JLCPCB:C_0402C104, C108, C111, C112, C113, C114, C115, C116, C117, C118
9LOGOLOGOG***, G***, G***, G***, G***, G***, G***, G***, G***
8220ΩPCM_JLCPCB:R_0402R201, R202, R203, R204, R205, R206, R207, R208
610kΩPCM_JLCPCB:R_0402R109, R301, R401, R502, R602, R702
510uFPCM_JLCPCB:C_0402C103, C105, C119, C301, C401
3100ΩPCM_JLCPCB:R_0402R501, R601, R701
3MDD2302PCM_JLCPCB:Q_SOT-23Q501, Q601, Q701
3Tactile Button, 160gfPCM_JLCPCB:SW_TS-1088-AR02016S101, S102, S103
3TestPoint_SmallTestPoint:TestPoint_Pad_1.5x1.5mmTP101, TP102, TP103
215pFPCM_JLCPCB:C_0402C101, C102
21kΩPCM_JLCPCB:R_0603R106, R108
227ΩPCM_JLCPCB:R_0603R110, R111
24.7uFPCM_JLCPCB:C_0603C106, C107
24.7uFPCM_JLCPCB:C_0402C109, C110
25.1kΩPCM_JLCPCB:R_0402R102, R103
2DNFResistor_SMD:R_0402_1005MetricR101, R104
2PSM712-LF-T7PCM_JLCPCB:SOT-23-3_L3.0-W1.7-P0.95-LS2.9-BRD101, D102
2SI2301CDS-T1-GE3PCM_JLCPCB:Q_SOT-23Q301, Q401
2SS14PCM_JLCPCB:D_SMAD301, D401
11kΩPCM_JLCPCB:R_0402R105
13.3uRP2350_60QFN_minimal:L_pol_2016L101
133ΩPCM_JLCPCB:R_0402R107
14.7kΩPCM_JLCPCB:R_0402R112
174HC595DPCM_JLCPCB:SOIC-16_L9.9-W3.9-P1.27-LS6.0-BLU201
1ABM8-272-T3Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY101
1AMS1117PCM_JLCPCB:SOT-223-3_L6.5-W3.4-P2.30-LS7.0-BRU102
1Connector, USB-TYPE-C-16PPCM_JLCPCB:TYPE-C-SMD_HX-TYPE-C-16PINJ101
1DNF DS18B20Connector_Wire:SolderWire-0.1sqmm_1x03_P3.6mm_D0.4mm_OD1mmU104
1RP2350_60QFNRP2350_60QFN_minimal:RP2350-QFN-60-1EP_7x7_P0.4mm_EP3.4x3.4mm_ThermalViasU103
1SM03B-SRSS-TBConnector_JST:JST_SH_SM03B-SRSS-TB_1x03-1MP_P1.00mm_HorizontalSWD
1Simple_Addon_v2EasyEDA_Lib:CONN-SMD_6P-P2.54_BH254VSSAO_PORT
1W25Q16JVSSPackage_SO:SOIC-8_5.3x5.3mm_P1.27mmU101

The 107 most common of 109 parts.

Similar boards

  • 4 layers52.6 × 40 mmBioSensorBox, the printed circuit board in 3D

    BioSensorBox

    JH2k00/BioSensorBox

    This repository contains the hardware and software for my project in the Advanced Topics in PCB Design lecture at the Technical University of Darmstadt

    56 parts
  • 2 layers165.1 × 95.3 mmPico concole v2 daughter board, the printed circuit board in 3D

    Pico concole v2 daughter board

    Crem2y/pico-console-v2-pcb

    pico console v2 board (firmware : https://github.com/Crem2y/pico-console-v2)

    232 parts1MIT
  • 2 layers63.5 × 40.6 mmRp2350a main board, the printed circuit board in 3D

    Rp2350a main board

    Crem2y/rp2350a_main_board

    rp2350a main board

    84 partsMIT
  • 4 layers50 × 111 mmBlade, the printed circuit board in 3D

    Blade

    JosephStew-art/Blade-PCB

    Blade PCB project

    118 parts
  • 2 layersPoc one, the printed circuit board in 3D

    Poc one

    ItsShadowCone/tmfl

    158 parts
  • 4 layers100 × 100 mm10k Hour Timer RP2040, the printed circuit board in 3D

    10k Hour Timer RP2040

    smaroukis/rp2040-timer

    An Eval Board for an RP2040 mcu + seven segment LED display + TM1638 driver + peripherals.

    180 parts
  • 2 layers160 × 110 mmAcquedotto test v4 finale, the printed circuit board in 3D

    Acquedotto test v4 finale

    igorilla666/water-controller

    Scheda di controllo basata sul modulo Waveshare ESP32-S3-ETH, con ingressi sensore, RS-485, pilotaggio rele, buzzer e alimentazione/protezioni dedicate.

    139 parts1CERN-OHL-S-2.0
  • 4 layers85.2 × 39.6 mmCheckpoint, the printed circuit board in 3D

    Checkpoint

    mikesmitty/voron-mods

    113 parts

Questions

How big is the Bccc sao rp2350a PCB?

It measures 92.3 × 99.8 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Bccc sao rp2350a use?

109 parts, built around the W25Q16JVSSIQ, 74HC595D, AMS1117 and MDD2302. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bccc sao rp2350a KiCad files?

From the aerospace-venoms/BCCC_Temperature_SAO repository on GitHub, at the commit this page was made from: the board is hardware/bccc_sao_rp2350a/bccc_sao_rp2350a.kicad_pcb and its schematic hardware/bccc_sao_rp2350a/3-digit-multiplexer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bccc sao rp2350a design in my own project?

Its repository states no licence, so its author keeps all rights: ask aerospace-venoms before reusing the design.