
Main panel
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

Yin Yang cute Cat keeb tht can also split :3
Cute Cat Split Keeb is an open-source printed circuit board by adonutartist, from the adonutartist/Cute-Cat-Split-Keeb repository on GitHub. It is a 2-layer board of 352.5 × 100 mm with 230 parts on 208 nets, routed with 2,990 tracks and 428 vias.
It is built around the SK6812MINI-E. Its parts include 138 diodes, 69 switches, 4 resistors and 4 ICs. It belongs with the keyboards and input boards and the nRF52 and nRF5x boards of this library.
A wireless split mechanical keyboard with per key kalih hotswap sockets, per key underglow RGB, a slide potentiometer for brightness control on the right half, and a rotary encoder for volume control on the left half. Uses a sandwich mount case (bottom case + plate + top frame) held together with heatset inserts and m2 20mm screws. The CAD features a unique design so it can join up to change into a full keeb visually. A project by Nemo made for Forge YSWS by Hackclub.
NOTE TO REVIEWER: I didn't make an assembly with case PCB and all components because Importing PCB into onshape was way too laggy and crashed, Adding lots of components also made onshape lag like crazy and crash so I abandoned doing that I hope you understand. I have a potato laptop from 2020 its really a budget laptop so please understand...
JOURNAL.mdFull 3D model render of the assembled keyboard (both halves)
PCB render/photo with components populated (both halves)
Schematic screenshots (1st image is left and 2nd image is right)
Exploded view of the sandwich mount stack (bottom case / plate / top frame)
Decal logo, custom encoder knob and hackclub logo emboss
➡️
| Layer | Thickness | Notes |
|---|---|---|
| Top frame | 6.3mm | Blind hole Ø3.5mm, 4.6mm deep for the heatset insert, no hole visible from outside |
| Plate | 1.5mm | Through hole Ø2.4mm for screw clearance |
| PCB | 1.6mm | |
| Bottom case (inner wall height) | 8mm | Clears the 3.05mm tall hotswap socket + ~3.16mm USB-C connector on the back layer with margin |
| Bottom case (bottom wall) | 3mm | Ø2.4mm x 1.2mm countersink on the underside so the screw head sits flush |
Case is attached using M2 x 4mm x 3.8mm OD brass heatset insert, M2 x 20mm countersunk screw.
Battery pocket: a local recessed pocket under the battery footprint on the inside of the bottom wall of bottom case (battery is the tallest bottom side component at ~5mm, taller than the general 6mm clearance zone needs). Battery wires are direct soldered to the BAT/GND test points, no connector.
See BOM.csv for the full parts list with references, footprints, product links, and important notes.
| Category | Cost (INR / USD) |
|---|---|
| Diodes (1N914, 68x) | ₹159.80 / $1.82 |
| RGB LEDs (SK6812MINI-E, 70x) | ₹619.20 / $7.04 |
| Battery-sense resistors (8.2k + 10k) | ₹20.34 / $0.23 |
| Slide potentiometer (RV1) | ₹286.78 / $3.26 |
| Hotswap sockets (68x) | ₹350.00 / $3.98 |
| Switches (68x) | ₹2,598.00 / $29.52 |
| Keycaps (1u / 1.75u / 1.5u) | ₹1,380.00 / $15.68 |
| MCP23017 GPIO expanders (2x) | ₹539.00 / $6.12 |
| XIAO BLE nRF52840 MCUs (2x) | ₹2,418.00 / $27.48 |
| LiPo batteries (2x) | ₹476.98 / $5.42 |
| PCB fabrication (panel) | ₹5,003.00 / $56.85 |
| Heatset inserts + case screws | ₹126.25 / $1.43 |
| Solder + solder wick | ₹621.00 / $7.06 |
| 3D-printed parts (case, plate, top frame, encoder knob) | $20.71 / ₹1,822.48 |
| GRAND TOTAL | ₹16,420.83 / $186.60 |
The keyboard uses two Seeed XIAO nRF52840 boards, one for each half. Separate firmware files are provided for the left and right halves.
.uf2 firmware filezmk_left.uf2 onto the bootloader drive (Found inside Firmware folder).zmk_right.uf2 onto the bootloader drive (Found inside Firmware folder).The firmware is built using ZMK with the Seeed XIAO nRF52840 target.
The provided firmware files are:
Firmware/
├── zmk_left.uf2
└── zmk_right.uf2The firmware currently represents the development stage prototype. Both left and right firmware builds complete successfully; physical flashing and keyboard testing will be performed once the PCBs and components are available.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 70 | SK6812MINI-E | LED_SMD:LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount | D106, D107, D108, D109, D110, D111, D112, D113, D114, D115, D116, D117, D118, D119, D120, D121 +54 |
| 68 | 1N914 | Diode_SMD:D_SOD-123 | D1, D10, D11, D12, D13, D14, D15, D16, D17, D18, D100, D101, D102, D103, D104, D105 +52 |
| 60 | SW_Push | switches_keeb:hotswap_switches | SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23, SW24 +44 |
| 4 | LOGO | LOGO | G***, G***, G***, G*** |
| 4 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.75u | SW34, SW37, SW66, SW67 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric | R2, R4 |
| 2 | 806k | Resistor_SMD:R_0805_2012Metric | R1, R3 |
| 2 | BAT | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP3 |
| 2 | GND | TestPoint:TestPoint_Pad_D2.0mm | TP2, TP4 |
| 2 | MCP23017x-x-SS | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U1, U3 |
| 2 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.5u | SW36, SW68 |
| 2 | SW_Push | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.25u | SW35, SW69 |
| 2 | XIAO-nRF52840-SMD | modified-XIAO-nRF52840-SMD:modified-XIAO-nRF52840-SMD | U2, U4 |
| 1 | R_Potentiometer | Potentiometer_THT:Potentiometer_Bourns_PTA2043_Single_Slide | RV1 |
| 1 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1 |
The 224 most common of 230 parts.

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.

Pwnsat/FlatSat
Flatsat v1.0 is a hardware based platform for aerospace cybersecurity research

adamws/kicad-kbplacer
KiCad plugin for automatic keyboard's key placement and routing

imchipwood/dumbpad
Simple 4x4 numpad with rotary encoder. Powered by QMK via ATmega32u4 Pro Micro

makerforgetech/modular-biped
An open source framework for creating a bipedal modular companion robot.


It measures 352.5 × 100 mm and has 2 copper layers, 1.6 mm thick.
230 parts, built around the SK6812MINI-E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the adonutartist/Cute-Cat-Split-Keeb repository on GitHub, at the commit this page was made from: the board is kicad/kicad.kicad_pcb and its schematic kicad/kicad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask adonutartist before reusing the design.