2 layers37 × 70.9 mm
Opendiag
maximus64/opendiag-hardware
OpenDIAG - Open Source OBD2 Interface (Hardware)
148 parts5CERN-OHL-S-2.0
2 layers60.8 × 62.1 mm
REMOTE IGNITION FINAL'
AdityaDev3/Remote-Ignition- Size
- 60.8 × 62.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 55
- Pads
- 162
- Tracks, vias
- 345, 82
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 28 May 2026
- Updated
- 1 Jun 2026
Overview
REMOTE IGNITION FINAL' is an open-source printed circuit board by AdityaDev3, from the AdityaDev3/Remote-Ignition repository on GitHub. It is a 2-layer board of 60.8 × 62.1 mm with 50 parts on 55 nets, routed with 345 tracks and 82 vias.
It is built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3 and AMS1117-5.0, with the MM3Z3V3, AO3400 and SI2369DS among its other parts. Its parts include 14 resistors, 8 capacitors, 6 connectors, 5 diodes and 3 ICs. It belongs with the ESP32 boards of this library.
Main components
6
ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsAMS1117-5.0
SOT-223-40℃~+125℃ 1 1.3V 15V 1A 5V 60dB Fixed Positive Short Circuit Protection、Thermal shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MM3Z3V3
SOD-323-65℃~+150℃ 1 Independent 1kΩ 3.1V~3.5V 3.3V 300mW 5uA 95Ω SOD-323 Zener Diodes ROHSonsemiZener Diodes
AO3400
SOT-23-55℃~+150℃ 1 N-channel 1.05nF 1.4V 1.5W 28mΩ@10V 30V 5.8A 77pF N-Channel SOT-23 MOSFETs ROHSGOODWORKMOSFETsSI2369DS
SOT-23-55℃~+150℃ 1 P-Channel 1.295nF 11.4nC@10V 130pF 150pF 2.5V 2.5W 30V 40mΩ@4.5V 7.6A P-Channel SOT-23 MOSFETs ROHSVishay IntertechnologyMOSFETs
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R10, R11, R14 |
| 4 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R8, R9 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H1, H2, H3, H4 |
| 3 | 47uf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C7, C8 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R4 |
| 2 | 22 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12, R13 |
| 2 | 22uf | Capacitor_SMD:C_1206_3216Metric | C1, C2 |
| 2 | MM3Z3V3 | Diode_SMD:D_SOD-323F | D1, D2 |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 100NF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 100nf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4 |
| 1 | 1uf | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 30k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | AO3400 | Package_TO_SOT_SMD:SOT-23-3 | Q2 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J7 |
| 1 | Conn_01x15_Pin | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J6 |
| 1 | ESP32-S3-WROOM-1 | esp32:esp32-s3-hole | U1 |
| 1 | G LED | LED_THT:LED_D3.0mm | D4 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5 |
| 1 | PYRO | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J4 |
| 1 | R LED | LED_THT:LED_D3.0mm | D3 |
| 1 | RST | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW2 |
| 1 | SERVO 1 | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | SERVO 1 |
| 1 | SERVO 2 | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mm | J3 |
| 1 | SI2369DS | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | boot | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW3 |
| 1 | input | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | J1 |
| 1 | main switch | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | SW1 |
| 1 | uart | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
The 47 most common of 50 parts.
Questions
How big is the REMOTE IGNITION FINAL' PCB?
It measures 60.8 × 62.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the REMOTE IGNITION FINAL' use?
50 parts, built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3, AMS1117-5.0 and MM3Z3V3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the REMOTE IGNITION FINAL' KiCad files?
From the AdityaDev3/Remote-Ignition repository on GitHub, at the commit this page was made from: the board is pcb/REMOTE IGNITION FINAL'/REMOTE IGNITION FINAL'.kicad_pcb and its schematic pcb/REMOTE IGNITION FINAL'/REMOTE IGNITION FINAL'.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the REMOTE IGNITION FINAL' design in my own project?
Its repository states no licence, so its author keeps all rights: ask AdityaDev3 before reusing the design.
Similar boards
- 2 layers121.1 × 136.9 mm
- 2 layers100 × 100 mm
- 2 layers65.5 × 41 mm
- 2 layers68.2 × 52.2 mm
Forward Ignition PCB
aditgoyal5/Forward_Ignition_PCB
This repository is about a printed circuit board I built for Team Sammard.
135 parts - 4 layers57.1 × 33.9 mm
- 2 layers60.5 × 51.5 mm
- 4 layers101 × 47 mm
