Skip to the content
4 layers47 × 39.5 mmStealthburner Toolhead PCB, the printed circuit board in 3D

Stealthburner Toolhead PCB

acha666/RP2040_ToolheadPCB_SB43

A Toolhead PCB for VORON StealthBurner based on RP2040

Size
47 × 39.5 mm
Copper layers
4
Thickness
1.19 mm
Parts
145
Nets
115
Pads
418
Tracks, vias
784, 224
Pours
189
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
29 Jun 2022
Updated
7 Oct 2022

Overview

Stealthburner Toolhead PCB is an open-source printed circuit board by acha666, from the acha666/RP2040_ToolheadPCB_SB repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 47 × 39.5 mm with 145 parts on 115 nets, routed with 784 tracks and 224 vias.

It is built around the RP2040, 74LVC2G17GW and LMR54410DBV, with the SI7021-A20-GM, 74LVC1G32Z and ADXL343BCC among its other parts. Its parts include 35 capacitors, 30 resistors, 12 connectors, 11 ICs and 7 diodes. It belongs with the RP2040 boards of this library.

Main components

12

README

readme.md

Stealthburner_Toolhead_PCB

中文文档/Chinese Document

Overview

This project contains a 3Dprinter Toolhead PCB for VORON StealthBurner Toolhead

The board has

  • RP2040 Microcontroller, connect to Raspberry PI with USB
  • TMC2209 for extruder motor
  • MAX31865 RTD-to-Digital Converter
  • Si7021/HTU21D humidity&temperature sensor
  • ADXL345 accrometer
  • Two 5pins fan connecter, fit with 2/3/4 wires, 12/24V fans
  • A 3pins probe connecter
  • A normal NTC Thermistor connector
  • A 2pins X Endstop connector
  • A 3pins 5V WS2812(Neopixel) LED connector
  • A 24V heater connector

Config Referencce

Programming Guide

Details

Microcontroller

You can easily buy a RP2040 chip by about 1USD, it's much cheaper than similar STM32 series MCU today

the RP2040 has some UART interfaces and a USB port, the USB is used for this design

MAX31865

the on-board MAX31865 chip supports 2/3/4 wires, PT100/PT1000 RTD. please notice that you should choose the reference resistor(430R/4.3K) and a capacitor(100nF/1uF) based on your RTD value. If you use an 3wire RTD, please connect the FORCE2 pin to PORCE+, otherwise connect it to GND. Please make sure that your wiring is correct. Check the Datasheet and Here for more information.

Si7021

This sensor is used to monitor chamber temp.

DS18B20 sensors are only supported on the "host mcu". A NTC thermistor should work too, so if a RTD sensor is used to measure hotend temp, you can have a try.

ADXL345

is for resonances measurement. Both ADXL343 and ADXL345 should work

FAN Connecter

support 2wires, 3wires(with speed monitor pin), 4wires(with PWM input and speed monitor)

12V/24V voltage can be set by the jumper. Check Here for more information.

If using 12V fan, be careful that the current required by the fan must not exceed the maximum current that the DC-DC can provide.

Neopixel LED

The 5V on the board is the LDO output, the output current is limited, and too many lamp beads cannot be connected in series.

Heater

be careful about selection on MOSFET, a N-Channel MOSFET with low RDSon at 4.5V

DC-DC

many models can be used, as long as they have same pin out

The inductor is 4x4mm package, as slim as possible(under 2mm height)

Inductor Options

  • WPN4012H (Sunlord)
  • SPH4012S PH4018 (Sunlord)
  • SWPA4010 SWPA4018 SWPA4020 (Sunlord)
  • SLW4010 (Sunltech)
  • FHD4012 (cjiang)

Buck converter options

  • LMR14006
  • LMR14010
  • LMR54410(not tested)
  • MP2451(not tested)
  • BL9342(not recommended)

please check the schmatic and chip datasheet for more details

Parts

145
QtyValueFootprintReferences
20100nFCapacitor_SMD:C_0402_1005MetricC3, C11, C13, C14, C15, C19, C20, C21, C22, C23, C24, C25, C27, C29, C30, C31 +4
1110KResistor_SMD:R_0402_1005MetricR1, R6, R9, R13, R16, R17, R18, R19, R20, R22, R23
6100RResistor_SMD:R_0402_1005MetricR7, R12, R14, R24, R25, R26
4G***kibuzzard-62BB2232kibuzzard-62BB2232, kibuzzard-62BB2232, kibuzzard-62BB2232, kibuzzard-62BB2232
310uFCapacitor_SMD:C_0402_1005MetricC8, C9, C17
3G***kibuzzard-62BB2226kibuzzard-62BB2226, kibuzzard-62BB2226, kibuzzard-62BB2226
20R11Resistor_SMD:R_0603_1608MetricR29, R30
210uFCapacitor_SMD:C_0603_1608MetricC5, C6
21KResistor_SMD:R_0402_1005MetricR5, R11
21N4148Diode_SMD:D_SOD-523D3, D5
21uFCapacitor_SMD:C_0402_1005MetricC16, C18
220KResistor_SMD:R_0402_1005MetricR27, R28
222uFCapacitor_SMD:C_0603_1608MetricC10, C12
227RResistor_SMD:R_0402_1005MetricR8, R10
274LVC2G17Package_TO_SOT_SMD:SOT-23-6U6, U8
2AO3400APackage_TO_SOT_SMD:SOT-23Q1, Q2
2Conn_01x02Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ4, J6
2Conn_01x021_Library:Molex_Micro-Fit_3.0_43650-0200_1x02_P3.00mm_HorizontalJ1, J9
2Conn_01x03Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_VerticalJ2, J8
2Conn_01x05Connector_Molex:Molex_PicoBlade_53261-0571_1x05-1MP_P1.25mm_HorizontalJ7, J10
2D_TVSDiode_SMD:D_SOD-523D4, D6
2LOGOLOGOG***, G***
2MountingHole1_Library:MountingHole_3mm_PadH1, H2
2SolderJumper_2_Open1_Library:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mmJP3, JP4
2SolderJumper_3_Open1_Library:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mmJP1, JP2
2TestPointTestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mmJ3, TP1
1100nF/1uFCapacitor_SMD:C_0603_1608MetricC36
1100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC32
1120R@100MHzInductor_SMD:L_0603_1608MetricFB1
11N4148WTDiode_SMD:D_SOD-523D2
11_Library:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm1_Library:SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mmJP5
12.2uFCapacitor_SMD:C_0402_1005MetricC2
122.1KResistor_SMD:R_0402_1005MetricR3
122nFCapacitor_SMD:C_0402_1005MetricC34
122uF/35VCapacitor_SMD:C_0805_2012MetricC1
1309KResistor_SMD:R_0402_1005MetricR2
14.7KResistor_SMD:R_0402_1005MetricR15
14.7uFCapacitor_SMD:C_0402_1005MetricC28
1430R/4.3KResistor_SMD:R_0805_2012MetricR31
16.2uHInductor_SMD:L_Taiyo-Yuden_NR-40xxL1
174LVC1G32Package_TO_SOT_SMD:SOT-23-5U11
1ADXL343Package_LGA:LGA-14_3x5mm_P0.8mm_LayoutBorder1x6yU14
1CSTNE12M0Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mmY1
1Conn_01x041_Library:JST_PH_S4B-PH-SM4-TB_1x04-1MP_P2.00mm_HorizontalJ11
1Conn_01x04Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalJ12
1G***kibuzzard-62BB2156kibuzzard-62BB2156
1G***kibuzzard-6309F118kibuzzard-6309F118
1G***kibuzzard-62BB1DD3kibuzzard-62BB1DD3
1G***kibuzzard-62BD8C8Dkibuzzard-62BD8C8D
1G***kibuzzard-62BB1FECkibuzzard-62BB1FEC
1G***kibuzzard-62BB1FE5kibuzzard-62BB1FE5
1G***kibuzzard-62E7C93Bkibuzzard-62E7C93B
1G***kibuzzard-63148E96kibuzzard-63148E96
1G***kibuzzard-62BD8A5Akibuzzard-62BD8A5A
1G***kibuzzard-62BB1FE8kibuzzard-62BB1FE8
1G***kibuzzard-62BD8C64kibuzzard-62BD8C64
1G***kibuzzard-62BB1C3Akibuzzard-62BB1C3A
1G***kibuzzard-62BD8846kibuzzard-62BD8846
1G***kibuzzard-62BB1FE0kibuzzard-62BB1FE0
1G***kibuzzard-62BD8A5Ekibuzzard-62BD8A5E
1G***kibuzzard-62E7C943kibuzzard-62E7C943
1G***kibuzzard-62E7C964kibuzzard-62E7C964
1G***kibuzzard-62F0BBF4kibuzzard-62F0BBF4
1G***kibuzzard-62BB2169kibuzzard-62BB2169
1G***kibuzzard-62BB2280kibuzzard-62BB2280
1G***kibuzzard-62BD8A57kibuzzard-62BD8A57
1G***kibuzzard-63148E7Fkibuzzard-63148E7F
1G***kibuzzard-63148E89kibuzzard-63148E89
1G***kibuzzard-62E7C936kibuzzard-62E7C936
1G***kibuzzard-62BD8A50kibuzzard-62BD8A50
1LMR54410Package_TO_SOT_SMD:SOT-23-6U1
1MAX31865xTPPackage_DFN_QFN:TQFN-20-1EP_5x5mm_P0.65mm_EP3.25x3.25mmU13
1ME6209A33M3GPackage_TO_SOT_SMD:SOT-23U3
1ME6209A50M3GPackage_TO_SOT_SMD:SOT-23U2
1NCResistor_SMD:R_0402_1005MetricR4
1QFN28_5X5_3X8_EPAD_TRI1_Library:TMC2209-LA-TU12
1RP20401_Library:RP2040TR7U7
1SMF28ADiode_SMD:D_SOD-123FD7
1SS14LDiode_SMD:D_SOD-123D1
1Si7021-A20Package_DFN_QFN:DFN-6-1EP_3x3mm_P1mm_EP1.5x2.4mmU9

The 141 most common of 145 parts.

Similar boards

  • 2 layers30 × 16 mmRc winch controller, the printed circuit board in 3D

    Rc winch controller

    laneboysrc/rc-winch-controller

    This project is for a winch controller for Radio Controlled cars that uses channel 3 to operate the winch remotely.

    13 parts6MIT
  • 2 layers112 × 57 mmCaravansensor, the printed circuit board in 3D

    Caravansensor

    MartinVerges/womolin-waterlevel

    DIY project to build a smart fuel sensor for RVs or in other projects. It is based on air pressure and is able to measure fresh water as well as grey and black water levels with high precision.

    226 parts17
  • 2 layers108.9 × 47.3 mmPowerBankPD, the printed circuit board in 3D

    PowerBankPD

    NgxLuis/30W-PD-Power-Bank

    PCB design - 30W High-Performance Power Bank utilizing SW3518, IP2326, and BM3451 for a 3S 21700 battery pack.

    105 parts1MIT
  • 8 layers37 × 37 mmPolski fc, the printed circuit board in 3D

    Polski fc

    marcinczeczko/marcin-fpv-fc

    157 parts
  • 2 layers55 × 8 mmAls board, the printed circuit board in 3D

    Als board

    blu006/blu_BOB_and_MISC

    My breakout boards and miscellaneous boards

    27 parts
  • 4 layers80.6 × 93.7 mmHw v1, the printed circuit board in 3D

    Hw v1

    Churrosoft/uEFI-v6.x

    Speeduino compatible board, x4 ignition channels, x4 injection channels, 2&4 wire IAC

    183 parts2
  • 4 layers84.5 × 129.5 mmBitaxeHex, the printed circuit board in 3D

    BitaxeHex

    bitaxeorg/ultraHex

    multi-ASIC Bitcoin miner

    369 parts190CERN-OHL-S-2.0
  • 6 layers55 × 120 mmBitForge Nano, the printed circuit board in 3D

    BitForge Nano

    WantClueTechnologies/BitForge-Nano

    This project presents a fully open-source Bitcoin mining hardware platform, designed for transparency, modularity, and extensibility.

    220 parts15CERN-OHL-S-2.0

Questions

How big is the Stealthburner Toolhead PCB PCB?

It measures 47 × 39.5 mm and has 4 copper layers, 1.19 mm thick.

What parts does the Stealthburner Toolhead PCB use?

145 parts, built around the RP2040, 74LVC2G17GW, LMR54410DBV and SI7021-A20-GM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Stealthburner Toolhead PCB KiCad files?

From the acha666/RP2040_ToolheadPCB_SB repository on GitHub, at the commit this page was made from: the board is Hardware/Stealthburner_Toolhead_PCB.kicad_pcb and its schematic Hardware/Stealthburner_Toolhead_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Stealthburner Toolhead PCB design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).