
M5-pantilt
HeliosH/stackchan-diy-guide
Stack-chan(スタックチャン)手挫完全指南:国内采购 / PCB 打样 / 3D 打印 / 装配 / 固件全流程教程 + 完整资料(STL / KiCad / 预编译固件)

An RS-485 FeatherWing for the Adafruit Feather system.
FeatherWing 485 is an open-source printed circuit board by W8LID, from the W8LID/RS-485-FW repository on GitHub. It is a 2-layer board of 50.8 × 22.9 mm with 22 parts on 33 nets, routed with 78 tracks and 11 vias.
It is built around the MAX3485ED, TVS0500DRV and BC857. Its parts include 7 resistors, 4 connectors, 3 ICs, 1 capacitor and 1 transistor. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
An RS-485 FeatherWing for the Adafruit Feather system.

The RS-485 FeatherWing provides level shifting of the TTL UART on Adafruit Feather type development boards. This board is based on the Maxim MAX3485 transceiver. It also provides an automatic direction control circuit so as to not require any additional GPIO pins for direction control.
This board is designed with minimal components in mind to keep complexity and cost to a minimum. Component footprints were chosen to allow for hand soldering and no special equipment required for assembly.
Note: The 4.7kΩ bias resistors (R1 & R3) should only be populated on a single device on an RS-485 bus. That is, if attempting to communicate between two RS-485 FeatherWings on the same bus, only populate R1 & R3 on a single FeatherWing.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100 | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R6, R7 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R1, R3 |
| 2 | TVS0500DRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U2, U3 |
| 1 | 0.01uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | BC857 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | MAX3485 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Screw_Terminal_01x03 | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_3-G-3.5_1x03_P3.50mm_Vertical | J3 |
| 1 | US001031 | KiCad:OSHW_Mono_0.1_Scale | OSHW_Mono_0.1_Scale |
| 1 | feather long | Connector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_Vertical | J1 |
| 1 | feather short | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J2 |
The 17 most common of 22 parts.

HeliosH/stackchan-diy-guide
Stack-chan(スタックチャン)手挫完全指南:国内采购 / PCB 打样 / 3D 打印 / 装配 / 固件全流程教程 + 完整资料(STL / KiCad / 预编译固件)

punkfab/pcb-corpus
235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark

will127534/gmax4002-breakout
A basic minimum GMAX4002 breakout board for Raspberry Pi

marouncz/IMU-navigation
This is a repository for my bachelor's thesis regarding IMU navigation

Tobias66662/Bachelor-Project-PCB-Designs
PCB to be used in the Enose (for Bachelor Project)



It measures 50.8 × 22.9 mm and has 2 copper layers, 1.6 mm thick.
22 parts, built around the MAX3485ED, TVS0500DRV and BC857. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the W8LID/RS-485-FW repository on GitHub, at the commit this page was made from: the board is KiCad/FeatherWing_485.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask W8LID before reusing the design.