2 layers
2 layers
TT Clone AY AT
Upcycle-Electronics/AVR-Transistor-Tester47- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 60
- Nets
- 54
- Pads
- 218
- Tracks, vias
- 219, 0
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 24 Nov 2017
- Updated
- 19 May 2018
Overview
TT Clone AY AT is an open-source printed circuit board by Upcycle-Electronics, from the Upcycle-Electronics/AVR-Transistor-Tester repository on GitHub. It is a 2-layer board with 60 parts on 54 nets, routed with 219 tracks and 0 vias.
It is built around the ATMEGA644-20AU, MCP1702-5002E/MB and SRV05-4, with the TL431A, SS9014BBU and P6KE6V8A among its other parts. Its parts include 24 resistors, 13 capacitors, 10 connectors, 4 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7
ATMEGA644-20AU
TQFP-44(10x10)-40℃~+85℃ 10bit 2.7V~5.5V 20MHz 2KB 32 4KB 64KB 8 Bit AVR Built-in FLASH TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MCP1702-5002E/MB
SOT-89-3-40℃~+125℃@(Tj) 1 13.2V 250mA 2uA 330mV@(250mA) 44dB@(100Hz) 5V Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
TL431A
SOT-23-20℃~+70℃@(Ta) 150mA 1uA 2.5V~36V 2.5V~36V 250uA Adjustable Parallel ±0.5% SOT-23 Voltage Reference ROHShongjiachengVoltage Reference
SS9014BBU
TO-92-3100 100mA 270MHz 300mV 450mW 45V 50nA 5V NPN TO-92-3 Bipolar (BJT) ROHSonsemiBipolar (BJT)
P6KE6V8A
DO-204AC10uA 13.4V 4nF 5.8V 57A 6.45V 600W IEC 61000-4-2 TVS Unidirectional DO-204AC ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)SS9012GBU
TO-92-31 PNP 100nA 20V 500mA 5V 600mV 625mW 64 PNP Standalone TO-92-3 Bipolar (BJT) ROHSonsemiBipolar (BJT)
README
README.mdAVR-Transistor-Tester
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitors_SMD:C_0805_HandSoldering | C3, C4, C5, C6, C13, C14 |
| 6 | 10k | Resistors_SMD:R_0805_HandSoldering | R11, R13, R18, R19, R23, R24 |
| 4 | 470k | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4, R6, R25 |
| 3 | 680R | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3, R5 |
| 2 | 10uF | Capacitors_THT:CP_Radial_D6.3mm_P2.50mm | C9, C10 |
| 2 | 1k | Resistors_SMD:R_0805_HandSoldering | R17, R20 |
| 2 | 22pF | Capacitors_SMD:C_0805_HandSoldering | C11, C12 |
| 2 | 27k | Resistors_SMD:R_0805_HandSoldering | R8, R15 |
| 2 | 3k3 | Resistors_SMD:R_0805_HandSoldering | R7, R12 |
| 2 | SS9014 | TO_SOT_Packages_THT:TO-92_Inline_Narrow_Oval | T1, T2 |
| 1 | 100k | Resistors_SMD:R_0805_HandSoldering | R9 |
| 1 | 10nF | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 16MHz | Crystals:Crystal_HC49-4H_Vertical | Y1 |
| 1 | 180k | Resistors_SMD:R_0805_HandSoldering | R21 |
| 1 | 1nF | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 20k | Resistors_SMD:R_0805_HandSoldering | R22 |
| 1 | 220nF | Capacitors_SMD:C_0805_HandSoldering | C7 |
| 1 | 2k2 | Resistors_SMD:R_0805_HandSoldering | R16 |
| 1 | 33k | Resistors_SMD:R_0805_HandSoldering | R10 |
| 1 | 7-12V DC Input | Connectors:BARREL_JACK | J1 |
| 1 | 9v Battery | Connectors:PINHEAD1-2 | J6 |
| 1 | ATMEGA644-20AU | Housings_QFP:TQFP-44_10x10mm_Pitch0.8mm | U1 |
| 1 | BL Adj 5k | Potentiometers:Potentiometer_Trimmer_Bourns_3296W | RV1 |
| 1 | Contrast 5k | Potentiometers:Potentiometer_Trimmer_Bourns_3296W | RV2 |
| 1 | Frequency Output | Socket_Strips:Socket_Strip_Straight_1x02_Pitch2.54mm | J2 |
| 1 | LCD | Pin_Headers:Pin_Header_Straight_1x14_Pitch2.54mm | J12 |
| 1 | LED1 | LEDs:LED_D3.0mm | LED1 |
| 1 | MCP1702-5002 | TO_SOT_Packages_THT:TO-92_Inline_Narrow_Oval | IC2 |
| 1 | Misc | Socket_Strips:Socket_Strip_Straight_1x08_Pitch2.54mm | J7 |
| 1 | P6KE6V8A | Diodes_SMD:D_SMA | D1 |
| 1 | PA Bus+VText | Socket_Strips:Socket_Strip_Straight_1x08_Pitch2.54mm | J4 |
| 1 | PB Bus | Socket_Strips:Socket_Strip_Straight_1x08_Pitch2.54mm | J10 |
| 1 | PC Bus | Socket_Strips:Socket_Strip_Straight_1x08_Pitch2.54mm | J11 |
| 1 | Programming Header | Pin_Headers:Pin_Header_Angled_2x03_Pitch2.54mm | ISP1 |
| 1 | SRV05-4 | TO_SOT_Packages_SMD:SOT-23-6 | IC4 |
| 1 | SS9012 | TO_SOT_Packages_THT:TO-92_Inline_Narrow_Oval | T3 |
| 1 | TL431A | TO_SOT_Packages_THT:TO-92_Molded_Narrow | IC3 |
| 1 | Test Probes | Socket_Strips:Socket_Strip_Straight_1x03_Pitch2.54mm | J5 |
| 1 | To Rotary Encoder | Socket_Strips:Socket_Strip_Straight_1x05_Pitch2.54mm | J3 |
More from Upcycle-Electronics/AVR-Transistor-Tester
1Similar boards
- 2 layers94 × 88.9 mm
- 2 layers
- 2 layers100 × 197.6 mm
Psu breakout
techana/psu-breakout
ATX/AT PSU breakout boards — passive 2-layer PCB with banana jacks for bench testing of vintage and modern PC power supplies
100 parts - 4 layers70 × 34 mm
- 2 layers77 × 77 mm
Elektroniikkapaja
ripaskajaska/Wireless-weather-station
Aalto University’s ELEC-8701 Elektronics workshop course's repository for Axel Soderberg, Roope Jaskari and Kalle Aro
76 parts - 2 layers95.2 × 67.5 mm
- 2 layers90 × 65 mm
- 2 layers50 × 49.4 mm
SD2IECplug
schenkmi/electronic-retro-computing-projects
In revision 2, the PCB size has been reduced by more than 50% and TAPuino support has been ditched. It now features a Micro SD slot and a few other improvements.
49 parts
Questions
What parts does the TT Clone AY AT use?
60 parts, built around the ATMEGA644-20AU, MCP1702-5002E/MB, SRV05-4 and TL431A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TT Clone AY AT KiCad files?
From the Upcycle-Electronics/AVR-Transistor-Tester repository on GitHub, at the commit this page was made from: the board is AY-AT Proto Mod 644/TT-Clone-AY-AT.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TT Clone AY AT design in my own project?
Its repository states no licence, so its author keeps all rights: ask Upcycle-Electronics before reusing the design.