
Main panel
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

A board to create my own beats, to make it mine, I will add my own doodles.
MIDI Keyboard is an open-source printed circuit board by TheTank87, from the TheTank87/MIDI-Keyboard repository on GitHub. It is a 2-layer board of 172 × 98 mm with 14 parts on 23 nets, routed with 171 tracks and 2 vias.
It is built around the SK6812MINI-E. Its parts include 4 switches, 3 diodes, 1 IC and 1 connector. It belongs with the audio and music and keyboards and input boards and the ESP32 boards of this library.
A board to create my own beats, to make it mine, I will add my own doodles.
This is the MIDI Keyboard. It is a small hand-held device that creates musical sounds in the right hands. It uses capacitative touch keys, buttons, switches, and a rotary knob. It also includes SK6812 MINI-E Neopixels that light up whenever I press those keyboard buttons. It also includes that USB plugin brain thing from the Starbie, but this time it's a little bit more powerful, featuring the waveshare.
| Designator | Footprint | Quantity | Value | Total Cost | Links |
|---|---|---|---|---|---|
| D1, D2, D3 | LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount | 3 | SK6812MINI-E | $3.36 | Link |
| J1 | Capacitative Keys | 1 | Capacitative Touch Buttons | ||
| RV1, RV2 | Potentiometer_Bourns_PTA1543_Single_Slide | 2 | Slider | $3.16 | Link |
| SW1, SW2, SW3 | Kailh Choc Low-Profile Switches | 3 | SW_Push | $6.04 | Link |
| SW4 | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | 1 | RotaryEncoder_Switch_MP | $1.44 | Link |
| U1 | Waveshare ESP32-S3-Zero | 1 | Waveshare ESP32-S3-ZERO | $6.62 | Link |
| Total Parts Cost | $17.46 | ||||
| Total Digikey Cost-Not using fast shipping | $8.67 | ||||
| Total JLCPCB | $12.20 | ||||
| Total Cost | $38.33 |
I started with the schematic design of my PCB and wired up everything using the guide as reference. However, I did make a mistake of accidentally swapping the TX and RX ports so I fixed that asap.
After that as fixed, I then went into the PCB editor and created my first design.
However, there was a major flaw in this design, that is, the wiring of the waveshare was not efficient and the entire layout was doomed to be messy. So I had to go back the schematic editor and redo the wiring so that it fits with a better layout.
As one can see, everything now wires up more cleanly. Insert crying-relief emoji...
I got the 3D models from the guide repo, and everything was pretty straight forward. It was pretty easy to figure out that you need to align the ports from the 3D model through the holes in the PCB. There was a mishap with the rotary encoder where rotating the x and z produced same side rotations which was not supposed to happen. So I had to restart kicad.
I then decided to add some silkscreen to my builds.
I also needed the circuit python for my board, so I went and downloaded the code.py and made changes to where the pins were wired so that it fits my board schematic. It turns out that I didn't need Ardunio IDE for this one as it's just using notepad and turning it into a .py file.
From past experiences, I also needed to add a whole lot more files not listed in the guide checklist on the HalfLife website. Which includes all my PCB files, the .pro file, and either a .cpl or .csv listing out all the positions of the components. I then reorganized the repo into folders.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | SK6812MINI-E | LED_SMD:LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount | D1, D2, D3 |
| 3 | SW_Push | Hackclub Footprints:Kailh Choc Low-Profile Switches | SW1, SW2, SW3 |
| 2 | Slider | Potentiometer_THT:Potentiometer_Bourns_PTA1543_Single_Slide | RV1, RV2 |
| 1 | Conn_01x07 | Tank's Library-Capacitative Keys:Capacitative Keys | J1 |
| 1 | LOGO | Graphics:Silkscreen2 | G*** |
| 1 | LOGO | Graphics:SilkscreenB1 | G*** |
| 1 | LOGO | Graphics:Silkscreen1 | G*** |
| 1 | RotaryEncoder_Switch_MP | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW4 |
| 1 | Waveshare ESP32-S3-ZERO | Hackclub Footprints:Waveshare ESP32-S3-Zero | U1 |

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

Bastardkb/Dilemma
The Dilemma is a vertical stagger low-profile keyboard with mods.

Pwnsat/FlatSat
Flatsat v1.0 is a hardware based platform for aerospace cybersecurity research

adamws/kicad-kbplacer
KiCad plugin for automatic keyboard's key placement and routing

imchipwood/dumbpad
Simple 4x4 numpad with rotary encoder. Powered by QMK via ATmega32u4 Pro Micro

makerforgetech/modular-biped
An open source framework for creating a bipedal modular companion robot.


It measures 172 × 98 mm and has 2 copper layers, 1.6 mm thick.
14 parts, built around the SK6812MINI-E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TheTank87/MIDI-Keyboard repository on GitHub, at the commit this page was made from: the board is PCB/MIDIKeyboard.kicad_pcb and its schematic PCB/MIDIKeyboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask TheTank87 before reusing the design.