

- Size
- 92.5 × 147.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 267
- Nets
- 175
- Pads
- 732
- Tracks, vias
- 1,033, 299
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Jun 2024
- Updated
- 30 Jan 2026
Overview
ADC is an open-source printed circuit board by TheSilentDefender, from the TheSilentDefender/ADC_Board_Aramaki_Lab repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 4-layer board of 92.5 × 147.5 mm with 267 parts on 175 nets, routed with 1,033 tracks and 299 vias.
It is built around the STM32F072CBT6, ADS7953SDBTR and OPA192ID, with the ADP3338AKCZ-5-REEL, PRTR5V0U2X and REF5025ID among its other parts. Its parts include 105 resistors, 85 capacitors, 53 connectors, 11 ICs and 3 switches. It belongs with the STM32 boards of this library.
Main components
8STM32F072CBT6
LQFP-48(7x7)-40℃~+85℃ 1.65V~3.6V 128KB 12bit 12bit 16KB 32 Bit 37 48MHz ARM Cortex-M0 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)ADS7953SDBTR
TSSOP-38-40℃~+125℃ 12 16 1LSB 1MHz 1uA 2.7V~5.25V 20MHz 71.7dB Multiplexers No SAR Serial port TSSOP-38 Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADC)OPA192ID
SOIC-8-18V~-2.25V、2.25V~18V -40℃~+125℃ 1 10MHz 140dB 1mA 200nV/℃ 20V/us 2pA 4.5V~36V 5.5nV/√Hz@1kHz 5pA 5uV 65mA Rail-to-Rail Input, Rail-to-Rail Output SOIC-8 Precision Op Amps ROHSTexas InstrumentsPrecision Op AmpsADP3338AKCZ-5-REEL
SOT-223-40℃~+85℃@(Ta) 1 110uA 190mV@(1A) 1A 5V 8V 95uVrms Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAnalog DevicesVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)REF5025ID
SOIC-8-40℃~+125℃@(Ta) 1.2mA 10mA 2.5V 2.7V~18V 3ppm/℃ 7.5uVp-p Fixed Series ±0.05% SOIC-8 Voltage Reference ROHSTexas InstrumentsVoltage ReferencesXC6206P332PR-G
SOT-89-3-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsASMD1206-150
1206-40℃~+85℃ 1.5A 1.9mm 100A 130mΩ 1mm 25mΩ 3.6mm 300ms 3A 6V 800mW 1206 Resettable Fuses ROHSShenzhen JDT FuseResettable Fuses
README
README.mdADC Hub for pGRAMS
- Has 48 ADC channels and an optional voltage divider can be used for RTDs.
- The ADCs only support a range of 0-5V. Any input outside the range may damage the ADCs on board.
- The board outputs ADC integer values with a 12-bit resolution(0-4095)
How to build
- Install platform.io on Visual Studio Code. You can also install it manually by following the documenation on the website.
- Open the folder using VSC and wait for platform.io to initialize
- Open the platform.io side panel and click build. This should automatically build with the settings in the configuation file.
How to flash
- Connect to the board in DFU mode or enter in "d" through serial (press the button on the top while you plug in the board)
- Assuming you followed the instuctions for building, you can click on build and upload which will automatic flash the board and restart it.
- If not you can download the bin file and flash it using dfu-util or any other DFU upgrade tool. For example,
sudo dfu-util -a 0 -i 0 -s 0x08000000:leave -D firmware.bin.
Parts
267| Qty | Value | Footprint | References |
|---|---|---|---|
| 54 | 33 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3, R16, R17, R18, R19, R20, R21, R28, R29, R100, R101, R102, R103, R104, R105 +38 |
| 51 | 270pF | Capacitor_SMD:C_0402_1005Metric | C32, C34, C35, C38, C39, C40, C41, C42, C43, C44, C45, C46, C47, C48, C49, C50 +35 |
| 48 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R11, R12, R13, R14, R15, R22, R23, R24, R25, R26, R27, R34, R35, R36, R37 +32 |
| 48 | Conn_01x02 | Connector_Molex:Molex_Mini-Fit_Jr_5566-02A_2x01_P4.20mm_Vertical | J2, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21, J22, J23, J24 +32 |
| 14 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C4, C5, C6, C10, C11, C12, C13, C14, C15, C19, C23, C24, C25 |
| 13 | 1uF | Capacitor_SMD:C_0402_1005Metric | C2, C3, C17, C18, C26, C27, C28, C29, C30, C31, C33, C36, C37 |
| 7 | 10uF | Capacitor_SMD:C_0402_1005Metric | C7, C8, C9, C16, C20, C21, C22 |
| 4 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J50, J51, J52, J53 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3mm_Pad | H1, H2, H3, H4 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4 |
| 3 | ADS7953SDBT | footprint:DBT38 | U2, U3, U4 |
| 3 | OPA192ID | footprint:SOIC127P599X175-8N | U5, U7, U8 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 60R@100MHz | Inductor_SMD:L_1206_3216Metric | L1 |
| 1 | ADP3338AKCZ-5-REEL | footprint:SOT230P700X180-4N | U11 |
| 1 | ASMD1206-150 | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | U6 |
| 1 | REF5025ID | footprint:SOIC127P599X175-8N | U9 |
| 1 | STM32F072CBT6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_CK_JS102011SAQN | SW3 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | XC6206P332PR-G | Package_TO_SOT_SMD:SOT-23 | U10 |
Similar boards
- 6 layers175 × 150 mm

- 2 layers26 × 36 mm

Generator alarm
Glebka/ARS
My first project based on the STM32 microcontroller family. It consists of an alarm module and a receiver. The alarm module utilizes the RCWL-0516 motion sensor, the STM32F030K6T6 microcontroller, which wakes up upon…
25 parts - 2 layers70 × 100 mm

- 2 layers49.9 × 41.2 mm

- 4 layers227.3 × 85 mm

Le capybara
sporkus/le_capybara_keyboard
Capactive sensing (EC) pcb for Le Chiffre keyboard
118 parts58CERN-OHL-W-2.0 - 2 layers227.3 × 84.9 mm

Stm32 hotswap chiffre
sporkus/le_chiffre_keyboard_stm32
Le Chiffre keyboard pcb with stm32F072
110 parts53CERN-OHL-W-2.0 - 2 layers209.7 × 76.3 mm

- 2 layers287.3 × 138.1 mm

Typomatrix stm32
josh-l-wang/typomatrix_stm32
typomatrix 3020 keyboard on STM32F072 controller
230 partsMIT
Questions
How big is the ADC PCB?
It measures 92.5 × 147.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ADC use?
267 parts, built around the STM32F072CBT6, ADS7953SDBTR, OPA192ID and ADP3338AKCZ-5-REEL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ADC KiCad files?
From the TheSilentDefender/ADC_Board_Aramaki_Lab repository on GitHub, at the commit this page was made from: the board is ADC/ADC.kicad_pcb and its schematic ADC/ADC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ADC design in my own project?
Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).