4 layers80 × 70 mm
4 layers130.5 × 88 mm
Trap panelized
TheCacophonyProject/trap-pcbs- Size
- 130.5 × 88 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 502
- Nets
- 117
- Pads
- 821
- Tracks, vias
- 811, 243
- Pours
- 24
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Mar 2022
- Updated
- 14 Oct 2024
Overview
Trap panelized is an open-source printed circuit board by TheCacophonyProject, from the TheCacophonyProject/trap-pcbs repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 130.5 × 88 mm with 502 parts on 117 nets, routed with 811 tracks and 243 vias.
It is built around the RP2040, LMR14050SDDA and TPS63070RNMR, with the W25Q128JVSIQ and PCF8563T/5 among its other parts. It belongs with the RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
LMR14050SDDA
SOP-8-EP-40℃~+125℃@(TJ) 1 2.5MHz 40uA 4V~40V 5A 800mV~28V Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Cycle-by-cycle current limiting、Frequency synchronization Step-down type SOP-8-EP DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
TPS63070RNMR
VQFN-15-HR(2.5x3)-40℃~+125℃@(TJ) 1 2.4MHz 2.5V~9V 2A 2V~16V 50uA Adjustable Buck-Boost Buck-Boost Built-in Yes VQFN-15-HR(2.5x3) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
PCF8563T/5
SO-8-40℃~+85℃ 0.25uA 1V~5.5V Battery low-voltage detection、Programmable clock output、Alarm function、Countdown timer I2C Yes SO-8 Real Time Clocks ROHSNXP SemiconductorsReal Time Clocks
README
README.mdtrap-pcbs
Parts
502| Qty | Value | Footprint | References |
|---|---|---|---|
| 363 | NPTH | NPTH | KiKit_MB_10_1, KiKit_MB_10_2, KiKit_MB_10_3, KiKit_MB_10_4, KiKit_MB_10_5, KiKit_MB_10_6, KiKit_MB_10_7, KiKit_MB_10_8, KiKit_MB_10_9, KiKit_MB_10_10, KiKit_MB_10_11, KiKit_MB_10_12, KiKit_MB_10_13, KiKit_MB_10_14, KiKit_MB_10_15, KiKit_MB_10_16 +347 |
| 16 | 1k | Resistor_SMD:R_0402_1005Metric | Board_0-R1, Board_0-R6, Board_0-R7, Board_0-R9, Board_0-R13, Board_0-R19, Board_0-R20, Board_0-R21, Board_0-R22, Board_0-R23, Board_0-R28, Board_0-R30, Board_0-R31, Board_0-R33, Board_0-R34, Board_0-R35 |
| 11 | 100n | Capacitor_SMD:C_0402_1005Metric | Board_0-C13, Board_0-C14, Board_0-C16, Board_0-C17, Board_0-C18, Board_0-C19, Board_0-C20, Board_0-C21, Board_0-C22, Board_0-C23, Board_0-C39 |
| 6 | 10k | Resistor_SMD:R_0402_1005Metric | Board_0-R11, Board_0-R12, Board_0-R18, Board_0-R24, Board_0-R29, Board_0-R1002 |
| 6 | 47uF | Capacitor_SMD:C_1206_3216Metric | Board_0-C25, Board_0-C33, Board_0-C34, Board_0-C35, Board_0-C36, Board_0-C37 |
| 6 | Fiducial | Fiducial | KiKit_FID_B_1, KiKit_FID_B_2, KiKit_FID_B_3, KiKit_FID_T_1, KiKit_FID_T_2, KiKit_FID_T_3 |
| 5 | 1uF | Capacitor_SMD:C_0402_1005Metric | Board_0-C9, Board_0-C10, Board_0-C15, Board_0-C40, Board_0-C41 |
| 4 | 22uF | Capacitor_SMD:C_0805_2012Metric | Board_0-C27, Board_0-C28, Board_0-C1001, Board_0-C1002 |
| 4 | 22uF | Capacitor_SMD:C_0603_1608Metric | Board_0-C1005, Board_0-C1006, Board_0-C1007, Board_0-C1008 |
| 4 | MountingHole_Pad | cacophony-library:MountingHole_3.2mm_M3 | Board_0-H1, Board_0-H2, Board_0-H3, Board_0-H4 |
| 3 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Board_0-Q1, Board_0-Q4, Board_0-Q6 |
| 3 | D_Shockley | Diode_SMD:D_SMA_Handsoldering | Board_1-D1, Board_1-D2, Board_1-D3 |
| 2 | 100k | Resistor_SMD:R_0402_1005Metric | Board_0-R25, Board_0-R1004 |
| 2 | 12pF | Capacitor_SMD:C_0402_1005Metric | Board_0-C11, Board_0-C12 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | Board_0-C32, Board_0-C38 |
| 2 | 27k | Resistor_SMD:R_0603_1608Metric | Board_0-R8, Board_0-R32 |
| 2 | 33ohm | Resistor_SMD:R_0402_1005Metric | Board_0-R3, Board_0-R4 |
| 2 | Conn_01x08 | Connector_JST:JST_XA_S08B-XASK-1_1x08_P2.50mm_Horizontal | Board_0-J9, Board_1-J4 |
| 2 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | Board_0-J3, Board_0-J8 |
| 2 | JCON_M16_2+4Pin | cacophony-library:jcon-2+4pin-m16 | Board_1-J5, Board_1-J6 |
| 2 | PIR_P924M-S | cacophony-library:PIR_P924M-S | Board_0-U5, Board_0-U6 |
| 2 | Q_PMOS_GSD | Package_TO_SOT_SMD:SOT-23 | Board_0-Q3, Board_0-Q5 |
| 2 | SW_Push_DPDT | cacophony-library:SW-TH_K3-2235D-F1 | Board_0-SW4, Board_0-SW5 |
| 2 | Servo | Connector_JST:JST_XA_B03B-XASK-1-A_1x03_P2.50mm_Vertical | Board_0-M1, Board_0-M2 |
| 2 | Switch_1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | Board_0-J4, Board_0-J5 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric | Board_0-R2 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | Board_0-C1009 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | Board_0-C31 |
| 1 | 10k | Potentiometer_SMD:Potentiometer_Bourns_TC33X_Vertical | Board_0-RV1 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | Board_0-C1004 |
| 1 | 150k | Resistor_SMD:R_0402_1005Metric | Board_0-R1003 |
| 1 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | Board_0-C1003 |
| 1 | 220uF | cacophony-library:CAP-SMD_BD8.0-L8.3-W8.3-LS9.3-FD | Board_0-C26 |
| 1 | 22nF | Capacitor_SMD:C_0402_1005Metric | Board_0-C30 |
| 1 | 4.7uH | cacophony-library:IND-SMD_L7.0-W6.6 | Board_0-L2 |
| 1 | 470k | Resistor_SMD:R_0402_1005Metric | Board_0-R1001 |
| 1 | 470nF | Capacitor_SMD:C_0603_1608Metric | Board_0-C29 |
| 1 | 47k | Resistor_SMD:R_0402_1005Metric | Board_0-R17 |
| 1 | 560 | Resistor_SMD:R_0603_1608Metric | Board_0-R26 |
| 1 | 680 | Resistor_SMD:R_0603_1608Metric | Board_0-R27 |
| 1 | Battery_Cell | cacophony-library:CAP-SMD_FL11E | Board_0-BT2 |
| 1 | Buzzer | cacophony-library:BUZ-TH_BD9.0-P5.00-D0.6-FD | Board_0-BZ1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | Board_0-J10 |
| 1 | Crystal | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Board_0-Y2 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Board_0-Y1 |
| 1 | D | Diode_SMD:D_SOD-523 | Board_0-D4 |
| 1 | D | Diode_SMD:D_SOD-123F | Board_0-D2 |
| 1 | DNF | Resistor_SMD:R_0402_1005Metric | Board_0-R10 |
| 1 | D_Shockley | Diode_SMD:D_SMA | Board_0-D17 |
| 1 | FerriteBead | Inductor_SMD:L_0805_2012Metric | Board_0-FB1001 |
| 1 | HT75xx-1-SOT89 | Package_TO_SOT_SMD:SOT-89-3 | Board_0-U4 |
| 1 | INDUCTOR | Inductor_SMD:L_1008_2520Metric | Board_0-L1001 |
| 1 | JCON_M16_04Pin | cacophony-library:jcon-4pin_m16 | Board_1-J2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | Board_0-D13 |
| 1 | LMR14050S | Package_SO:TI_SO-PowerPAD-8 | Board_0-U8 |
| 1 | Logo | cacophony-library:logo | Board_0-U11 |
| 1 | PCF8563T | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Board_0-U7 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_SKQG_WithStem | Board_0-SW1 |
| 1 | RP2040 | cacophony-library:RP2040-QFN-56 | Board_0-U3 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | Board_0-J6 |
| 1 | SW_Coded_SH-7010 | cacophony-library:SW-TH_6P-L10.0-W10.0-P2.54-LS7.6_TSR-10 | Board_0-SW3 |
| 1 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | Board_0-JP1 |
| 1 | Switch_1 | cacophony-library:JST_SH_BM02B-SRSS-TB_1x02-1MP_P1.00mm_Vertical | Board_0-J7 |
| 1 | Switch_2 | cacophony-library:JST_SH_BM02B-SRSS-TB_1x02-1MP_P1.00mm_Vertical | Board_0-J2 |
| 1 | TPL0401B-10-Q1 | Package_TO_SOT_SMD:Texas_R-PDSO-G6 | Board_0-U1 |
| 1 | TPS63070RNMR | cacophony-library:TPS63070 | Board_0-U1001 |
| 1 | TestPoint_2Pole | cacophony-library:test-point-2p | Board_0-TP1001 |
| 1 | USB_BOOT | Button_Switch_SMD:SW_SPST_SKQG_WithStem | Board_0-SW2 |
| 1 | USB_B_Micro | cacophony-library:MICRO-USB-TH_MICRO-USB-A14 | Board_0-J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | Board_0-U9 |
More from TheCacophonyProject/trap-pcbs
4- 2 layers60 × 47 mm
- 4 layers58 × 29 mm
- 2 layers30 × 30 mm
Similar boards
- 4 layers80 × 99 mm
- 2 layers170 × 73 mm
- 2 layers65 × 65 mm
LMR14050SDDA reference
luxas/special-computing-machine
Let's make a Raspberry Pi cluster similar to real data centers!
49 parts5Apache-2.0 - 4 layers86 × 56 mm
- 4 layers73.6 × 59.8 mm
Leak sensor v1
lewipewi/leakwatch
A multi-channel leak sensor for equipment enclosures. Instead of reporting "wet / dry" like a normal leak probe, it measures how wet each enclosure is, on a separate channel per enclosure, and carries a second circuit…
90 parts - 6 layers73 × 75.5 mm
Tc2-main pcb
TheCacophonyProject/thermal-camera-v2
tc2-panel.py uses KiKit to build the manufacturing panel from the individual board files.
219 partsCERN-OHL-W-2.0 - 2 layers94 × 94 mm
3axis magnitometer
NarodniySputnik/Gladiolus-1
Gladiolus-1 - автономный модуль для приема и передачи изображений в формате SSTV (Slow Scan TeleVision) на малом космическом аппарате (МКА) формата CubeSat
96 parts9GPL-3.0 - 4 layers68.6 × 56 mm
Cartridge
coco-chameleon/chameleon-hardware
TRS-80 Color Computer cartridge emulator
95 partsCERN-OHL-W-2.0
Questions
How big is the Trap panelized PCB?
It measures 130.5 × 88 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Trap panelized use?
502 parts, built around the RP2040, LMR14050SDDA, TPS63070RNMR and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Trap panelized KiCad files?
From the TheCacophonyProject/trap-pcbs repository on GitHub, at the commit this page was made from: the board is trap-panelized/trap-panelized.kicad_pcb and its schematic ir-camera-backplate/ir-camera-backplate.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Trap panelized design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).