Skip to the content

TPS63070RNMR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 2.4MHz 2.5V~9V 2A 2V~16V 50uA Adjustable Buck-Boost Buck-Boost Built-in Yes VQFN-15-HR(2.5x3) DC-DC Converters ROHS

Part id
ti/TPS63070RNMR
Category
DC DC Converters
Package
VQFN-15-HR(2.5x3)
Pins
17
In stock
12,440 at JLCPCB (C109322)
Used on
89 open-source boards

Overview

The TPS63070RNMR is a DC DC Converter made by Texas Instruments in a VQFN-15-HR(2.5x3) package with 17 pins. -40℃~+125℃@(TJ) 1 2.4MHz 2.5V~9V 2A 2V~16V 50uA Adjustable Buck-Boost Buck-Boost Built-in Yes VQFN-15-HR(2.5x3) DC-DC Converters ROHS.

PCBKit's library has its footprint (EasyEDA_Cloud:VQFN-15_L3.0-W2.5-P0.50-BL, from EasyEDA), ready for a KiCad board. 12,440 are in stock at JLCPCB (part C109322). 89 open-source boards in 66 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

EasyEDA_Cloud:VQFN-15_L3.0-W2.5-P0.50-BLFrom EasyEDA

From the datasheet

13
Supply, least
2 V · VIN, recommended operating minimum · p. 4
Supply, most
16 V · VIN, recommended operating maximum · p. 4
Supply, absolute maximum
20 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · Junction temperature absolute maximum · p. 4
Takes working
59 µA · sum of typical VIN and VOUT quiescent currents, no load, VIN = 6 V, VOUT = 5 V, PFM · p. 6
Takes asleep
2 µA · Shutdown current typical, VEN = 0 V, VIN = 5 V · p. 6
Gives
2 A · Output current maximum, VIN or VOUT ≥ 4.5 V, VOUT/VIN ≤ 1 · p. 6
Feedback reference
800 mV · Feedback voltage typical, PS/SYNC = VIN · p. 7
Current limit
3.6 A · Average positive input current limit typical, VIN = 5 V, VOUT = 6.5 V · p. 7
Switches at
2.4 MHz · Oscillator frequency typical · p. 7
Junction to air (VQFN)
63 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (VQFN)
42 K/W · Junction-to-case top thermal resistance · p. 5
Junction to board (VQFN)
13 K/W · Junction-to-board thermal resistance · p. 5

What it is and has

11
Input voltage range
2.0 V to 16 V · p. 1
Output voltage range
2.5 V to 9 V · p. 1
Efficiency
Up to 95% · p. 1
DC accuracy in PWM mode
+/- 1% · p. 1
DC accuracy in PFM mode
+3% / -1% · p. 1
Power good
Power Good Output · p. 1
Load disconnect
During shutdown · p. 1
Protection
Overtemperature · p. 1
Protection
Input / output overvoltage · p. 1
Output voltage option
Adjustable; output discharge off · p. 3
Package
VQFN, 2.5 mm x 3 mm · p. 1

Around it

5
res 1kΩ to 1MΩ
between VIN and PS/SYNC; Series resistor recommended when PS/SYNC is tied to VIN; may be shared with EN if both inputs connect to VIN. · p. 12
ind 1.5 µH
between L1 and L2; Nominal effective inductance; recommended range 0.7 to 2.8 uH. · p. 4
cap 10 µF
between VIN and PGND; Nominal capacitance connected to VIN; minimum 4.7 uF. · p. 4
cap 100 nF
between VAUX and GND; Nominal capacitance for the internal voltage regulator. · p. 4
cap 47 µF
between VOUT and PGND; Nominal total output capacitance for nominal 1.5 uH inductance; recommended range 15 to 470 uF; account for ceramic capacitor DC bias. · p. 4

Specifications

71
ParameterConditionsAs printedPage
Voltage rangeVIN, PS/SYNC, EN, VSELmin -0.3 · max 20 V4
Voltage rangeL1min -0.3 · max 20 V4
Voltage rangeL1, transient for t<10ns, while switchingmin -3 · max 25 V4
Voltage rangeL2, PG, VOUT, FBmin -0.3 · max 12 V4
Voltage rangeL2, transient for t<10ns, while switchingmin -3 · max 15 V4
Voltage rangeAUXmin -0.3 · max 7 V4
Voltage rangeFB2min -0.3 · max 3 V4
Operating junction temperature Tjmin -40 · max 150 °C4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±500 Vmax 500 V4
Supply voltage at VINmin 2 · max 16 V4
Output Voltagemin 2.5 · max 9 V4
Effective Inductance1.5 uH nominalmin 0.7 · typ 1.5 · max 2.8 uH4
Capacitance connected to VIN pin10 uF nominalmin 4.7 · typ 10 uF4
Capacitance connected to VAUX pin100 nF nominaltyp 100 nF4
Total capacitance connected to VOUT pin47 uF nominal; nominal inductance 1.5 uH; account for ceramic capacitor DC biasmin 15 · typ 47 · max 470 uF4
duty cycle in buck mode over recommended operating conditionsmin 30 %4
duty cycle in buck mode over recommended operating conditions but effective output capacitance Cout,eff ≥ 40uF; effective inductance L,eff = 0.7uH to 1.8uHmin 20 %4
Operating junction temperature range TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJATPS63070x, VQFN, 13 PINStyp 63 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)TPS63070x, VQFN, 13 PINStyp 42 °C/W5
Junction-to-board thermal resistance RθJBTPS63070x, VQFN, 13 PINStyp 13 °C/W5
Junction-to-top characterization parameter ψJTTPS63070x, VQFN, 13 PINStyp 2.4 °C/W5
Junction-to-board characterization parameter ψJBTPS63070x, VQFN, 13 PINStyp 13 °C/W5
Input voltage range VINonce started; Vout ≥ 3.0 Vmin 2 · max 16 V6
Input voltage range VINfor start-up; Vout < 3.0 Vmin 3 · max 16 V6
Output current IOUTduring operation with either VIN ≥ 4.5 V or VOUT ≥ 4.5 V and the boost factor (VOUT/VIN) ≤ 1max 2 A6
Quiescent current IQinto VIN; IOUT= 0 mA, VEN = VIN = 6 V, PFM; VOUT = 5 V; Tj = -40°C to 85°Ctyp 54 · max 103 uA6
Quiescent current IQinto VIN; IOUT= 0 mA, VEN = VIN = 6 V, PFM; VOUT = 5 V; Tj = -40°C to 125°Cmax 133 uA6
Quiescent current IQinto VOUT; IOUT= 0 mA, VEN = VIN = 6 V, VOUT = 5 V, PFM; Tj = -40°C to 85°Ctyp 5 · max 9 uA6
Quiescent current IQinto VOUT; IOUT= 0 mA, VEN = VIN = 6 V, VOUT = 5 V, PFM; Tj = -40°C to 125°Cmax 17 uA6
Shutdown current ISDVEN = 0 V; Tj = -40°C to 85°C; VIN = 5Vtyp 2 · max 12 uA6
Shutdown current ISDVEN = 0 V; Tj = -40°C to 85°Cmax 26 uA6
Undervoltage lockout threshold VUVLOVIN voltage fallingmin 1.7 · typ 1.85 · max 1.95 V6
Undervoltage lockout hysteresis VUVLO,THVIN voltage risingmin 525 · typ 850 mV6
Thermal shutdown TSDtyp 160 °C6
Thermal shutdown hysteresis TSDtyp 20 °C6
Threshold Voltage rising edge for EN pin and PS/SYNC used for PWM/PFM mode change VTHRmin 0.77 · typ 0.8 · max 0.83 V6
Threshold Voltage falling edge for EN pin and PS/SYNC used for PWM/PFM mode change VTHFmin 0.67 · typ 0.7 · max 0.73 V6
VSEL low level input voltage; PS/SYNC low level input voltage when used for synchronization VILmax 0.3 V6
VSEL high level input voltage; PS/SYNC high level input voltage when used for synchronization VIHmin 1.1 V6
EN, PS/SYNC, VSEL input currentmax 0.2 uA6
PG output low voltage VOLIPG = -1 mAmax 0.4 V6
PG output leakage current ILKGPG pin high impedance; VPG = 5 Vmax 0.2 uA6
PG sink current IPGmax 1 mA6
Power Good Threshold Voltage, rising Vout VTH_PGmin 94.5 · typ 96 · max 98.5 %6
Power Good Threshold Voltage, falling Vout VTH_PGmin 90 · typ 92 · max 94.5 %6
TPS63070/TPS630702 output voltage range VOUTTPS63070; observe minimum duty cycle in buck modemin 2.5 · max 9 V7
TPS63070/TPS630702 feedback voltage VFBTPS63070; PS/SYNC = VINtyp 800 mV7
feedback leakagefor adjustable version; VFB = 0.8Vmax 100 nA7
TPS63070/TPS630702 feedback voltage accuracy VFBTPS63070; PS/SYNC = GND (PWM mode)min -1 · max 1 %7
TPS63070/TPS630702 feedback voltage accuracy VFBTPS63070; PS/SYNC = VIN (PFM mode); VIN ≥ 3Vmin -1 · max 3 %7
Oscillator frequency fSWmin 2100 · typ 2400 · max 2700 kHz7
Frequency range for synchronizationmin 2100 · max 2800 kHz7
Average, positive input current limit IIN,maxVIN = 5.0V; VOUT = 6.5V; Tj = 0°C to 125°Cmin 3050 · typ 3600 · max 4150 mA7
Average, negative input current limit IIN,maxVIN = 5.0V; VOUT = 6.5V; Tj = 0°C to 125°Cmin 1100 · typ 1800 mA7
High side switch on resistance RDS(ON)-BUCKVIN = 5 Vtyp 50 · max 80 mΩ7
Low side switch on resistance RDS(ON)-BUCKVIN = 5 Vtyp 100 · max 160 mΩ7
High side switch on resistance RDS(ON)-BOOSTVIN = 5 Vtyp 40 · max 70 mΩ7
Low side switch on resistance RDS(ON)-BOOSTVIN = 5 Vtyp 80 · max 125 mΩ7
FB2 resistance to GND with VSEL = high RDS(ON)-FB2VSEL = hightyp 25 · max 100 Ω7
Input leakage current into FB2 with VSEL=low ILKGVFB = VFB2 = 0.8V; VSEL=lowmax 100 nA7
FB2 sink currentmax 100 uA7
Line regulationPower Save Mode disabledtyp 0.07 %/V7
Load regulationPower Save Mode disabledtyp 0.2 %/A7
Maximum bias voltage VAUXVIN ≥ VOUT; VIN < 6V; minimum is VIN - 0.3 Vmax 7 V7
Maximum bias voltage VAUXVIN < VOUT; minimum is VOUT - 0.3 Vmax 7 V7
Start-up delay tdelaytime from EN = VIH to device starts switchingtyp 70 us7
soft-start time tSStime to ramp from 5% to 95% of Vout; buck mode; VIN = 7.2 V, Vout = 3.3 V, Iout = 500 mAtyp 400 us7
soft-start time tSStime to ramp from 5% to 95% of Vout; boost mode; VIN = 3.0 V, Vout = 3.3 V, Iout = 250 mAtyp 850 us7

Pins, by the datasheet

15
1 PS/SYNC
Pull low for forced PWM or high for PWM/PFM power save mode; apply a clock to synchronize to an external frequency. · p. 3
2 PG
Open drain power good output. · p. 3
3 VAUX
Connect a capacitor for the internal voltage regulator; must not be loaded externally. · p. 3
4 GND
Control / logic ground. · p. 3
5 FB
Voltage feedback of adjustable versions. · p. 3
6 FB2
Connect a resistor from FB to FB2 to change the feedback divider ratio; VSEL high increases output voltage; leave open or connect to GND if unused. · p. 3
7 VOUT
Buck-boost converter output. · p. 3
8 VOUT
Buck-boost converter output. · p. 3
9 L2
Connection for Inductor. · p. 3
10 PGND
Power ground. · p. 3
11 L1
Connection for Inductor. · p. 3
12 VIN
Supply voltage for power stage. · p. 3
13 VIN
Supply voltage for power stage. · p. 3
14 EN
Pull high to enable the device or low to disable it. · p. 3
15 VSEL
Voltage scaling input; a high level enables a transistor pulling FB2 to GND. · p. 3

Ordering codes, by the datasheet

4
TPS63070RNMR
VQFN-HR (RNM) · 15 pins; 3000, LARGE T&R; -40 to 125 °C; lead finish Call TI | Sn · p. 35
TPS63070RNMR.A
VQFN-HR (RNM) · 15 pins; 3000, LARGE T&R; -40 to 125 °C; lead finish SN · p. 35
TPS63070RNMT
VQFN-HR (RNM) · 15 pins; 250, SMALL T&R; -40 to 125 °C; lead finish Call TI | Sn · p. 35
TPS63070RNMT.A
VQFN-HR (RNM) · 15 pins; 250, SMALL T&R; -40 to 125 °C; lead finish SN · p. 35

Open-source boards using it

89See all 89
  • 4 layers52 × 52 mmMoto gps rev a1, the printed circuit board in 3D

    Moto gps rev a1

    mx3353672833-debug/moto-gps-waveshare

    MOTO GPS · Waveshare ESP32-S3 1.75C 圆屏导航 + iPhone App | Author: Maler X | Noncommercial, attribution required | Experimental

    112 parts529
  • 2 layers102.7 × 56.8 mmRecoveryBoard, the printed circuit board in 3D

    RecoveryBoard

    psas/lv3.1-recovery

    design, analysis, CAD, and testing for the LV3.1 recovery system

    158 parts13
  • 2 layers25 × 22 mmREV2 Dyno Rectifier PCB 2, the printed circuit board in 3D

    REV2 Dyno Rectifier PCB 2

    zumdar/ContactlessBikeDynamo

    Contactless Bicycle Dynamo (using eddy currents) and a light!

    38 parts10
  • 2 layers107.3 × 82.8 mmSMPS 12V-5V, the printed circuit board in 3D

    SMPS 12V-5V

    jvanderberg/Kicad-jlcpcb-example

    JLCPCB KiCad Integration Example

    19 parts7MIT
  • 4 layers43.2 × 17.8 mmGeekble Nano ESP32S3, the printed circuit board in 3D

    Geekble Nano ESP32S3

    SooDragon/Geekble-nano-ESP32S3

    Geekble nano ESP32S3

    94 parts6CC0-1.0
  • 4 layers25 × 67 mmTinkerNav V25, the printed circuit board in 3D

    TinkerNav V25

    Tinkerbug-Robotics/TinkerNav

    RTK Rover and Base Station Firmware for TinkerNav Boards

    54 parts6
  • 4 layers52 × 115.7 mmMp3-player, the printed circuit board in 3D

    Mp3-player

    espcaa/mp3-player

    a minimalist open source pocket sized¹ mp3 player

    143 parts5
  • 4 layers51.4 × 40.8 mm12S UAV UGV PMU, the printed circuit board in 3D

    12S UAV UGV PMU

    Manoj-Davu/pcb-design-portfolio

    43 parts2

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the TPS63070RNMR?

Yes. the footprint EasyEDA_Cloud:VQFN-15_L3.0-W2.5-P0.50-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS63070RNMR?

VQFN-15-HR(2.5x3), with 17 pins. Its footprint is drawn on this page.

Where is the TPS63070RNMR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS63070RNMR?

JLCPCB lists it as part C109322, with 12,440 in stock; the sellers' links on this page open their listings.

What can replace the TPS63070RNMR?

Parts like it in the library: the TPS630701RNMT by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS63070RNMR?

89 boards in 66 repositories on GitHub; the most starred are listed on this page, with their KiCad files.