

EPS ControlUnit
Electrical Power System
- Size
- 55.1 × 45.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 97
- Pads
- 222
- Tracks, vias
- 314, 39
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 22 May 2023
- Updated
- 20 May 2025
Overview
EPS ControlUnit is an open-source printed circuit board by Student-Satellite-IITB, from the Student-Satellite-IITB/Electrical-Power-System repository on GitHub. It is a 2-layer board of 55.1 × 45.2 mm with 55 parts on 97 nets, routed with 314 tracks and 39 vias.
It is built around the STM32L476VET6, AMS1117-3.3 and TPS3824-33QDBVRQ1. Its parts include 16 capacitors, 10 connectors, 7 resistors, 3 ICs and 2 diodes. It belongs with the STM32 boards of this library.
Main components
3STM32L476VET6
LQFP-100(14x14)-40℃~+85℃ 1.71V~3.6V 128KB 12bit 12bit 32 Bit 512KB 80MHz 82 ARM Cortex-M4 Built-in FLASH LQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTPS3824-33QDBVRQ1
SOT-23-5-40℃~+125℃@(Ta) 1 1.1V~5.5V 15uA 2.93V 200ms Active Low Push-pull Voltage Monitor Yes Yes SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICs
README
README.mdELECTRICAL POWER SYSTEM
This repository contains all software and hardware for the Electrical Power subsystem for the IITBSSP CubeSat mission

Current status:
- EPS PDB and PMB Assembly
- Battery Unit Development Board
- Power Distribution and Regulation Development Board
- MATLAB/Simulink model of EPS in development
- Testing of Solar Input Development Board
- Testing of Control Unit Development Board
Completed:
- EPS PDB Board Design
- EPS PMB Board Design
- Solar Input Development Board
- EPS Control Unit Development Board
Maintained by:
- Ameya Marakarkandy ameya.marakarkandy@gmail.com
- Yash Paritkar paritkary25@gmail.com
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C7, C8, C9, C10, C11 |
| 6 | 1k5 | Resistor_SMD:R_0805_2012Metric | R2, R3, R4, R5, R7, R8 |
| 4 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J3, J4, J5, J6 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_Pad | H1, H2, H3, H4 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | 3V3, 3V3, TP1, TP9 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | GND, GND, TP2 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C2, C6 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 22uF | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | Conn_01x01_Pin | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J9, J10 |
| 2 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J8 |
| 2 | Jumper_2_Bridged | TestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | LDO_EN, WD_EN |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 32MHz | Crystal:Crystal_SMD_Abracon_ABM8AIG-4Pin_3.2x2.5mm | Y1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | Conn_01x02_Pin | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J7 |
| 1 | EPS_LED | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | FerriteBead | Inductor_SMD:L_0805_2012Metric | 120R1 |
| 1 | LOGO | LOGO | G*** |
| 1 | POWER_LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | STM32L476VET6 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | SW_SPDT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | SW1 |
| 1 | TPS3824-33QDBVRQ1 | TPS3824:tps3824 | U3 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_GCT_USB3076-30-A | J2 |
More from Student-Satellite-IITB/Electrical-Power-System
2- 4 layers92 × 92 mm

- 2 layers40.6 × 36.8 mm

Similar boards
- 4 layers92 × 92 mm

- 4 layers60.8 × 64.8 mm

- 4 layers53.2 × 138.8 mm

- 2 layers290.1 × 130 mm

- 2 layers26.2 × 45.5 mm

PL18 multiprotocol
pascallanger/DIY-Multiprotocol-TX-Module
Multiprotocol TX Module (or MULTI-Module) is a 2.4GHz transmitter module which controls many different receivers and models.
24 parts1.9kGPL-3.0 - 4 layers99 × 53.3 mm

PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
199 parts1.7kApache-2.0 - 4 layers85 × 56 mm

- 4 layers100 × 54 mm

32Bit shift register
MaltWhiskey/Mega-Cube
16x16x16 PL9823 Cube with Teensy 4.0 and FlexIO driver
64 parts766
Questions
How big is the EPS ControlUnit PCB?
It measures 55.1 × 45.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the EPS ControlUnit use?
55 parts, built around the STM32L476VET6, AMS1117-3.3 and TPS3824-33QDBVRQ1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EPS ControlUnit KiCad files?
From the Student-Satellite-IITB/Electrical-Power-System repository on GitHub, at the commit this page was made from: the board is DevelopmentBoards/EPS Control Unit/EPS_ControlUnit/EPS_ControlUnit.kicad_pcb and its schematic DevelopmentBoards/Battery/BatteryUnit/BatteryUnit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EPS ControlUnit design in my own project?
Its repository states no licence, so its author keeps all rights: ask Student-Satellite-IITB before reusing the design.