Skip to the content
2 layers60 × 60 mmIo analog pwm, the printed circuit board in 3D

DMX Demonstrator

Size
60 × 60 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
19
Pads
82
Tracks, vias
254, 68
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
8 Feb 2024
Updated
30 Sep 2024

Overview

Io analog pwm is an open-source printed circuit board by SparkyBobo, from the SparkyBobo/dmxdemonstrator repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 60 × 60 mm with 30 parts on 19 nets, routed with 254 tracks and 68 vias.

It is built around the LM317T, LM339 and NE555. Its parts include 9 resistors, 7 capacitors, 3 ICs, 3 connectors and 1 diode.

Main components

3

README

hardware/io-analog/pwm/README.md

DMX Demonstrator Analog PWM Module (DMX-IO4)

status

Overview

The PWM IO module can generate a 0 to adjustable positive voltage PWM signal where the duty cycle tracks the level of a channel. It is configurable to generate multiple output voltages to adapt it to any voltage range required. The default values listed in the schematic generate 0 to +10V since this is a common lighting control signal. The PWM IO module can also generate a 0 to +5V PWM signal where the duty cycle tracks the level of a channel. Both outputs can be used at the same time.

Online parts list

For a complete list of parts, see:

You can also buy some of the parts for the analog modules online from a Wishlist:

PCB

You can order the PCB from OHS Park:

Voltage Options

The DMX-IO4 amplifies the output from the DMX-IO2 into the desired voltage range. Two resistors are adjusted to modify the voltage range: the voltage regulator resistors R4-R5. The following table provides the values for common voltages:

Output Voltage|R4|R5|Input Voltage --------------|-----------|------- 5V|392 1%|11.8k 1%|8v-24v 10V|392 1%|27.4k 1%|12v-24v 12V|392 1%|34.0k 1%15v-24v 15V|392 1%|43.2k 1%|20v-24v 24V|392 1%|71.5k 1%|28v-30v

R4 uses the same values in all configuration to reduce the number of parts required. There is nothing terrible special about this value, it just happen to work for a wide range of output voltages and is the value mention in the LM317 data sheet. If you want to create a custom voltage range, use the following formulas:

Vo = 1.25v + (1 + (R5 / R4)) Vi = Vo + 2v or 3v (for higher current, use 3v)

Version History

Rev 1.5

  • Added pullup resistors.
  • Removed J3.

Rev 1.4

  • Added thermal relief for TO-220
  • Switch RV1 from 3299W (tall) to 3299P (short)

Rev 1.3

  • Switch to smaller screw terminal connectors
  • Add silkscreen values
  • Remove COAX power connector

Rev 1.2

  • Converted to a family of modules so avoid multiple DACs for each analog option
  • Standardize layout to allow stacking of analog modules
  • Provide an adjustable voltage output PWM signal for use with external dimmers and LED drivers

Rev 1.1

  • Switched to a stand-alone module

Rev 1.0

  • Initial draft

Parts

30
QtyValueFootprintReferences
610kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R3, R6, R7, R8, R9
4MountingHoleMountingHole:MountingHole_3.2mm_M3MH1, MH2, MH3, MH4
30.1uFCapacitor_THT:C_Rect_L4.6mm_W2.0mm_P2.50mm_MKS02_FKP02C1, C2, C3
20.68uFCapacitor_THT:C_Rect_L4.6mm_W2.0mm_P2.50mm_MKS02_FKP02C4, C5
210uFCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC6, C7
1footprints:OSHW-LOGO-S
110kPotentiometer_THT:Potentiometer_Bourns_3299P_HorizontalRV1
11N5819Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1
12.74k 1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5
1330Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1392 1%Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4
1Analog ExtensionConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ1
1LM317TPackage_TO_SOT_THT:TO-220-3_Horizontal_TabDownU3
1LM339Package_DIP:DIP-14_W7.62mmU2
1LOGOfootprints:logo_cr_5x5G***
1NE555Package_DIP:DIP-8_W7.62mmU1
1OutputConnector_Phoenix_MC:PhoenixContact_MC_1,5_5-G-3.81_1x05_P3.81mm_HorizontalJ2
1PowerConnector_Phoenix_MC:PhoenixContact_MC_1,5_2-G-3.81_1x02_P3.81mm_HorizontalJ4

More from SparkyBobo/dmxdemonstrator

12
  • 2 layers60 × 60 mmIo dmx-512, the printed circuit board in 3D

    Io dmx-512

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    29 parts2GPL-3.0
  • 2 layers60 × 60 mmLed driver current, the printed circuit board in 3D

    Led driver current

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    29 parts2GPL-3.0
  • 2 layers60 × 60 mmIo analog voltage, the printed circuit board in 3D

    Io analog voltage

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    27 parts2GPL-3.0
  • 2 layers60 × 60 mmIo analog core, the printed circuit board in 3D

    Io analog core

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    26 parts2GPL-3.0
  • 2 layers68.6 × 53.3 mmTransmitter, the printed circuit board in 3D

    Transmitter

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    25 parts2GPL-3.0
  • 2 layers68.6 × 53.3 mmScrambler, the printed circuit board in 3D

    Scrambler

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    23 parts2GPL-3.0
  • 2 layers100 × 90 mmDimmer control, the printed circuit board in 3D

    Dimmer control

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    22 parts2GPL-3.0
  • 2 layers68.6 × 53.3 mmReceiver, the printed circuit board in 3D

    Receiver

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    22 parts2GPL-3.0
  • 2 layers100 × 90 mmClock control, the printed circuit board in 3D

    Clock control

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    19 parts2GPL-3.0
  • 2 layers60 × 60 mmLed driver voltage, the printed circuit board in 3D

    Led driver voltage

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    19 parts2GPL-3.0
  • 2 layers68.6 × 53.3 mmTransmitter adapter, the printed circuit board in 3D

    Transmitter adapter

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    15 parts2GPL-3.0
  • 2 layers68.6 × 53.3 mmReceiver io, the printed circuit board in 3D

    Receiver io

    SparkyBobo/dmxdemonstrator

    DMX Demonstrator

    5 parts2GPL-3.0

Similar boards

  • 2 layers79.2 × 97 mmInterrupter, the printed circuit board in 3D

    Interrupter

    profdc9/DRSSTC-PCB-Pack

    A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.

    80 parts59
  • 2 layers99.1 × 99.1 mmPower supply panelized, the printed circuit board in 3D

    Power supply panelized

    thebiguno/microcontroller-projects

    A home for a bunch of microcontroller projects which don't warrant their own repos.

    223 parts75
  • 2 layers60 × 50 mmEurorack volca, the printed circuit board in 3D

    Eurorack volca

    grappendorf/eurorack-volca

    Mounting Korg Volcas into a Eurorack system

    25 parts19
  • 2 layers100 × 80 mmRti, the printed circuit board in 3D

    Rti

    cceh/rti

    Reflectance Transformation Imaging

    58 parts15
  • 2 layers151.3 × 50.8 mm6ch preamp, the printed circuit board in 3D

    6ch preamp

    dilshan/6ch-af-preamplifier

    5.1 channel audio preamplifier

    126 parts12MIT
  • 2 layersLEDControlPCBSMDV2, the printed circuit board in 3D

    LEDControlPCBSMDV2

    BioARTS-Lab/Miniature_Microscope

    3D-printed fluorescence miniature microscope

    31 parts6GPL-3.0
  • 2 layers90.4 × 60.5 mmPSU, the printed circuit board in 3D

    PSU

    jscrane/PSU

    Software-controlled variable-voltage power supply with current and power monitoring

    19 parts5Apache-2.0

Questions

How big is the Io analog pwm PCB?

It measures 60 × 60 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Io analog pwm use?

30 parts, built around the LM317T, LM339 and NE555. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Io analog pwm KiCad files?

From the SparkyBobo/dmxdemonstrator repository on GitHub, at the commit this page was made from: the board is hardware/io-analog/pwm/io-analog-pwm.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Io analog pwm design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).