Skip to the content
4 layers70 × 40 mmUHoubolt PCB ECU, the printed circuit board in 3D

µHoubolt Engine Control Unit KiCad project

Size
70 × 40 mm
Copper layers
4
Thickness
1.6 mm
Parts
216
Nets
157
Pads
867
Tracks, vias
1,647, 414
Pours
31
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
16 Nov 2020
Updated
23 Sep 2023

Overview

UHoubolt PCB ECU is an open-source printed circuit board by SpaceTeam, from the SpaceTeam/uHoubolt_PCB_ECU repository on GitHub, published under the CERN-OHL-W-2.0 licence. It is a 4-layer board of 70 × 40 mm with 216 parts on 157 nets, routed with 1,647 tracks and 414 vias.

It is built around the TS30041-M050QFNR, D1213A-04V and ICM-20602, with the MCP1700-3302E/TT and W25Q256JV among its other parts. Its parts include 78 resistors, 50 capacitors, 27 connectors, 24 ICs and 17 diodes. It belongs with the STM32 boards of this library.

Main components

5

README

README.md

µHoubolt Engine Control Unit (ECU) Hardware

Features

  • 3 RC Servo outputs with position feedback and current measurement
  • 2 High-current low side FET outputs with current measurement
  • 3 Pyro outputs with high side switch (supplied separately from main supply), continuity check, current measurement and current limiting
  • 6 Pressure sensor inputs, individually configurable for 0-150mV differential, 0-5V single ended and 4-20mA
  • 3 Temperature sensor inputs for resistive types
  • Status LEDs on all outputs, voltage rails and two user programmable
  • 2 CAN-FD buses, multiple connectors per bus for simple daisy-chaining
  • Debug interface with SWD and UART
  • 70x40mm 4-layer PCB, additional power and CAN connectors on back side

Known Issues

  • Wrong Footprint for STM
  • Igniter continuity check not working without Pyro voltage
  • Missing low pass filter for servo current measurement
  • Switching on the 12V supply (or power cycling it) when the pyro supply is already active can initiate igniters (poblematic in combination with issue in PMU, see PMU Known Issues and EuRoC flight report). Pull down resistors on igniter enable lines are missing.
  • Using current sense amps for the pressure sensor inputs is bad, their low input impedance significantly reduces the measured values. Wasn't a problem (and wasn't even noticed?) as the measurements are still linear (tested by GATE) and the sensors were calibrated against a Baluff sensor, but should be avoided in future revisions by using instrumentation amplifiers (e.g. INA350).

Parts

216
QtyValueFootprintReferences
39100nCapacitor_SMD:C_0402_1005MetricC1, C2, C12, C17, C21, C22, C23, C24, C25, C26, C27, C30, C31, C32, C33, C34 +23
2010kResistor_SMD:R_0603_1608MetricR5, R7, R13, R14, R15, R16, R23, R25, R29, R39, R42, R45, R48, R51, R54, R58 +4
15120Resistor_SMD:R_0603_1608MetricR10, R11, R17, R18, R19, R20, R28, R30, R32, R57, R59, R61, R66, R74, R77
141kResistor_SMD:R_0603_1608MetricR3, R6, R24, R27, R35, R49, R50, R53, R56, R64, R69, R75, R76, R78
1256kResistor_SMD:R_0603_1608MetricR4, R8, R12, R33, R34, R36, R62, R63, R65, R67, R68, R70
9INA180B1Package_TO_SOT_SMD:SOT-23-5U1, U9, U10, U12, U13, U14, U15, U16, U17
610k/160Resistor_SMD:R_0603_1608MetricR2, R22, R38, R41, R44, R47
65k6/0Resistor_SMD:R_0603_1608MetricR1, R21, R37, R40, R43, R46
6PressureConnector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_VerticalJ7, J12, J13, J14, J15, J23
6V_SELJumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mmJP1, JP3, JP4, JP5, JP6, JP7
510m 1WResistor_SMD:R_1206_3216MetricR26, R31, R52, R55, R60
522µCapacitor_SMD:C_0603_1608MetricC18, C19, C42, C54, C55
52µ2Capacitor_SMD:C_0603_1608MetricC16, C20, C28, C29, C36
5D1213A-04VTXV_LIB:SOT-563U20, U21, U22, U23, U24
4CAN1Connector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_VerticalJ3, J5, J35, J37
4CAN2Connector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_VerticalJ4, J6, J36, J38
4MHMountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
3PYRO 1LED_SMD:LED_0603_1608MetricD8, D11, D12
3PyroTXV_LIB:Molex_SL_1x2_VerticalJ11, J21, J22
3SISA88DN or similarTXV_LIB:PowerPAK_1212-8Q1, Q2, Q3
3ServoTXV_LIB:Molex_Nano-Fit_105309-xx04_1x04_P2.50mm_VerticalJ9, J18, J19
3ServoLED_SMD:LED_0603_1608MetricD14, D15, D16
3TEMPConnector_JST:JST_GH_BM02B-GHS-TBT_1x02-1MP_P1.25mm_VerticalJ8, J16, J17
3TPS1HC100Package_SO:HTSSOP-14-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3x3.1mmU11, U18, U19
2350mAFuse:Fuse_1206_3216MetricF1, F2
2MCP2562FDx-x_MFPackage_DFN_QFN:DFN-8-1EP_3x3mm_P0.65mm_EP1.55x2.4mmU4, U5
2OUT 1LED_SMD:LED_0603_1608MetricD6, D9
2ShottkyDiode_SMD:D_SOD-123FD7, D10
2SolenoidTXV_LIB:Molex_Nano-Fit_105309-xx02_1x02_P2.50mm_VerticalJ10, J20
110µCapacitor_SMD:C_0805_2012MetricC10
13V3LED_SMD:LED_0603_1608MetricD17
14µ7TXV_LIB:SRN4018TA-4R7ML2
15VLED_SMD:LED_0603_1608MetricD3
1DebugConnector_PinHeader_1.27mm:PinHeader_2x04_P1.27mm_Vertical_SMDJ2
1ICM-20602Package_LGA:LGA-16_3x3mm_P0.5mm_LayoutBorder3x5yU7
1LED 1LED_SMD:LED_0603_1608MetricD4
1LED 2LED_SMD:LED_0603_1608MetricD5
1MCP1700-3302EPackage_TO_SOT_SMD:SOT-23U3
1PYROLED_SMD:LED_0603_1608MetricD2
1Power InTXV_LIB:Molex_MegaFit_1x03_Vertical_DoublesidedJ1
1STM32G491MET6-LQFP80Package_QFP:LQFP-80_12x12mm_P0.5mmU6
1Servo Voltage SelectTXV_LIB:Jumper3_6x2mm_Vias23JP2
1SpaceTeam_LOGOTXV_LIB:ST_Logo_newG1
1SpeakerTXV_LIB:Piezo_BuzzerLS1
1TS30041-M050QFNRPackage_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.75x1.75mm_ThermalViasU2
1TVS 3V3TXV_LIB:SOD882DD13
1TXC-7COscillator:Oscillator_SMD_TXC_7C-4Pin_5.0x3.2mmX1
1VINLED_SMD:LED_0603_1608MetricD1
1W25Q256JVTXV_LIB:WSON-8-8x6mmU8

Similar boards

  • 4 layers59 × 7.1 mmUHoubolt PCB PMU, the printed circuit board in 3D

    UHoubolt PCB PMU

    SpaceTeam/uHoubolt_PCB_PMU

    µHoubolt Power Management Unit KiCad project

    166 partsCERN-OHL-W-2.0
  • 4 layers82.6 × 76 mmUHoubolt PCB GNSS, the printed circuit board in 3D

    UHoubolt PCB GNSS

    SpaceTeam/uHoubolt_PCB_RCU

    90 partsCERN-OHL-W-2.0
  • 4 layers31 × 100 mmKp ptr, the printed circuit board in 3D

    Kp ptr

    PTR-projects/PTR_mega_hardware

    Welcome to the KPPTR-hardware repository! This repository contains the design files for the hardware components used in the KPPTR project.

    208 parts3MIT
  • 4 layers80 × 140 mmIOB V3, the printed circuit board in 3D

    IOB V3

    SpaceTeam/Lamarr_IOB_V3

    280 parts1
  • 4 layers70 × 80 mmEasycomm, the printed circuit board in 3D

    Easycomm

    stamina/easyriderc

    Motorcycle ECU STM32 ARM Cortex 4 source code and hardware PCB design

    41 parts14GPL-3.0
  • 2 layers193 × 72 mmDevice, the printed circuit board in 3D

    Device

    jayis1/hacker-devices

    Full-cycle hardware designs for security research devices — each device is a subfolder with its own README, schematics, PCB layout, and software stack

    6 parts2
  • 2 layers15 × 31 mmPocketAdmin, the printed circuit board in 3D

    PocketAdmin

    krakrukra/PocketAdmin

    oshw keystroke injection device ( badusb )

    25 parts241MIT

Questions

How big is the UHoubolt PCB ECU PCB?

It measures 70 × 40 mm and has 4 copper layers, 1.6 mm thick.

What parts does the UHoubolt PCB ECU use?

216 parts, built around the TS30041-M050QFNR, D1213A-04V, ICM-20602 and MCP1700-3302E/TT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the UHoubolt PCB ECU KiCad files?

From the SpaceTeam/uHoubolt_PCB_ECU repository on GitHub, at the commit this page was made from: the board is uHoubolt_PCB_ECU.kicad_pcb and its schematic HighCurrentOutput.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the UHoubolt PCB ECU design in my own project?

Its repository publishes it under the CERN-OHL-W-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).