Skip to the content
4 layers43 × 32.5 mmOpen TraceV1, the printed circuit board in 3D

Cheap open source Mechanical 3D Lidar

Size
43 × 32.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
34
Nets
65
Pads
197
Tracks, vias
413, 70
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
9 Oct 2026
Updated
13 Oct 2026

Overview

Open TraceV1 is an open-source printed circuit board by Shubhayu-Banerjee, from the Shubhayu-Banerjee/Open-Trace repository on GitHub. It is a 4-layer board of 43 × 32.5 mm with 34 parts on 65 nets, routed with 413 tracks and 70 vias.

It is built around the RP2040, SN74LVC245APW and W25Q16JVSSIQ, with the AMS1117-3.3 and USBLC6-2SC6 among its other parts. Its parts include 17 capacitors, 6 resistors, 5 ICs, 2 connectors and 2 switches. It belongs with the RP2040 boards of this library.

Main components

5

README

README.md

OpenTrace

OpenTrace is a custom RP2040-based USB logic analyzer designed to capture digital signals from external circuits for inspection on a computer. This repository documents the hardware design completed so far.

OpenTrace v1

What has been designed

RP2040 core

  • Selected the Raspberry Pi RP2040 as the main MCU.
  • Designed the core around an external W25Q16JV QSPI flash (16 Mbit / 2 MB).
  • Added the 12 MHz crystal oscillator circuit, using the RP2040 reference topology as the design basis.
  • Added local supply decoupling capacitors and the RP2040's 3.3 V / 1.1 V regulator-related connections.
  • Tied TESTEN low.
  • Added a RUN reset circuit using a 10 kΩ pull-up to +3V3 and a normally-open momentary switch to GND.

USB-C interface

  • Added a USB-C receptacle for USB 2.0 device connectivity.
  • Added separate 5.1 kΩ pull-down resistors from CC1 and CC2 to GND.
  • Combined the receptacle's duplicate USB 2.0 contacts correctly: A6/B6 for D+ and A7/B7 for D−.
  • Added a USBLC6-2SC6 for USB D+/D− ESD protection.
  • Added an AMS1117-3.3 regulator stage to derive 3.3 V from USB VBUS in the current schematic.

Eight-channel input stage

  • Selected the SN74LVC245A-family octal buffer, with the current schematic using SN74LVC245APW.
  • Set DIR low for A-to-B signal flow.
  • Set active-low /OE low to enable the outputs.
  • Added a 100 nF bypass capacitor at the buffer's supply.
  • Added an eight-signal probe connector (J2) and wired its eight signals to buffer inputs A1–A8.
  • Wired the corresponding B1–B8 outputs to RP2040 GPIOs GPIO25 through GPIO18, respectively:
Probe / buffer channelRP2040 GPIO
Channel 1 (A1 → B1)GPIO18
Channel 2 (A2 → B2)GPIO19
Channel 3 (A3 → B3)GPIO20
Channel 4 (A4 → B4)GPIO21
Channel 5 (A5 → B5)GPIO22
Channel 6 (A6 → B6)GPIO23
Channel 7 (A7 → B7)GPIO24
Channel 8 (A8 → B8)GPIO25

The mapping above records the schematic mapping discussed so far; it must still be checked against the final display/encoder pin assignments.

Probe-input ESD decision

  • Evaluated multiple eight-channel and single-/multi-line ESD protection options, including the SP4065-08ATG, TPD4E05U06, DRTR5V0U4S-7, PESD5V0U1BA, PESD5V0L1BA, NUP4114, and PESD5V0C2BDFZ.
  • No probe-side ESD protector was selected as a verified solution. The main blocker was finding a part that was available, had a practical footprint, and had transient/clamping characteristics appropriately evaluated against the SN74LVC245A input limits.
  • The current design decision is to omit the dedicated probe-input ESD array for this revision, rather than add an unverified component. This leaves the exposed probe inputs without dedicated ESD protection and is a known limitation.
  • The USBLC6-2SC6 remains assigned to USB D+/D−, not to the probe inputs.

Important current design details

ItemCurrent design
Main MCURaspberry Pi RP2040
QSPI flashW25Q16JV, 16 Mbit / 2 MB
Clock12 MHz crystal circuit
USBUSB-C, USB 2.0
USB ESDUSBLC6-2SC6 on D+/D−
USB-to-3.3 V regulatorAMS1117-3.3 candidate
Probe bufferSN74LVC245APW
Probe inputs8 digital channels
Probe-to-GPIO mappingGPIO25, GPIO24, GPIO23, GPIO22, GPIO21, GPIO20, GPIO19, GPIO18
Probe ESDOmitted for current revision; not protected by a dedicated ESD array
ResetRUN with 10 kΩ pull-up and momentary switch to GND
Boot configurationTESTEN tied low; flash/BOOTSEL arrangement needs final verification

Decisions and trade-offs made

  • Chose RP2040 rather than a more complex FPGA or another MCU for this revision, prioritizing a feasible custom board and PIO-based deterministic sampling.
  • Kept the external QSPI flash and 12 MHz crystal as part of the bare-MCU design.
  • Used a USB-C connector with the correct device-side CC pull-down approach.
  • Added dedicated ESD protection to the USB data lines.
  • Chose the SN74LVC245A-family device as the eight-channel input buffer.
  • Deferred probe-input ESD protection because candidate parts were unavailable or could not be validated as a complete protection solution within the current design effort.
  • Prioritized getting a coherent, manufacturable first PCB over adding a component whose electrical suitability was uncertain.

Known limitations / items not yet verified

This repository describes the design work completed so far; it does not claim the PCB has been fabricated or tested.

  • The probe inputs have no dedicated ESD array in the current revision. Treat them as unprotected inputs.

References

BOM

ReferenceQtyValueDNPExclude from BOMExclude from BoardFootprintDatasheet
C1,C3,C4,C6,C7,C8,C9,C10,C11,C17,C1811100nFCapacitor_SMD:C_0603_1608Metric
C5,C12,C15,C1641 µFCapacitor_SMD:C_0603_1608Metric
C13,C14215pCapacitor_SMD:C_0603_1608Metric
D11LEDLED_SMD:LED_0805_2012Metric
J11USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalUSB Type-C Specification
J21Conn_01x16_PinConnector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_Vertical
R1,R2,R631kResistor_SMD:R_0603_1608Metric
R3110kResistor_SMD:R_0603_1608Metric
R4,R525.1kResistor_SMD:R_0603_1608Metric
SW11Boot_SELButton_Switch_THT:SW_PUSH_6mm
SW21RUNButton_Switch_THT:SW_PUSH_6mm
U11RP2040Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mmRP2040 Datasheet
U21SN74LVC245APWPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmTI Datasheet
U31USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6ST Datasheet
U41W25Q16JVSSPackage_SO:SOIC-8_5.3x5.3mm_P1.27mmWinbond Documentation
U51AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2AMS1117 Datasheet
Y11Crystal_GND24Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm

Parts

34
QtyValueFootprintReferences
11100nFCapacitor_SMD:C_0603_1608MetricC1, C3, C4, C6, C7, C8, C9, C10, C11, C17, C18
41 µFCapacitor_SMD:C_0603_1608MetricC5, C12, C15, C16
31kResistor_SMD:R_0603_1608MetricR1, R2, R6
215pCapacitor_SMD:C_0603_1608MetricC13, C14
25.1kResistor_SMD:R_0603_1608MetricR4, R5
110kResistor_SMD:R_0603_1608MetricR3
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U5
1Boot_SELButton_Switch_THT:SW_PUSH_6mmSW1
1Conn_01x16_PinConnector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_VerticalJ2
1Crystal_GND24Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1LEDLED_SMD:LED_0805_2012MetricD1
1RP2040Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mmU1
1RUNButton_Switch_THT:SW_PUSH_6mmSW2
1SN74LVC245APWPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU2
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U3
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalJ1
1W25Q16JVSSPackage_SO:SOIC-8_5.3x5.3mm_P1.27mmU4

Similar boards

  • 2 layers185 × 83 mmMass Spring Damper SysID Lab, the printed circuit board in 3D

    Mass Spring Damper SysID Lab

    Scalable-Open-Source-Labs/Mass-Spring-Damper-SysID-Lab

    An open source Mass-Spring-Damper to assist with teaching System Identification

    135 parts1MIT
  • 4 layers99 × 84 mmRobotic arm controller, the printed circuit board in 3D

    Robotic arm controller

    bejaouihamza/robotic_arm_controller

    Traditional servo controllers simply send PWM signals. This board goes further:

    140 parts
  • 4 layers86 × 47 mmSmd board, the printed circuit board in 3D

    Smd board

    hinatadayo/nixie-token-display

    115 parts
  • 4 layers55.2 × 24.4 mmLogic analyzer, the printed circuit board in 3D

    Logic analyzer

    BlackPancakes/RP2040-Logic-Analyzer

    An open-source, high-speed, multi-channel logic analyzer based on the popular Raspberry Pi RP2040 microcontroller. The board was designed in KiCad with a strong focus on signal integrity and miniaturization.

    54 parts3
  • 4 layers219 × 108.5 mmZ80DevBoard, the printed circuit board in 3D

    Z80DevBoard

    gianluca-rainis/Z80DevBoard

    An advanced development board for the Z80 microprocessor, powered by an RP2040.

    182 parts7CERN-OHL-S-2.0
  • 4 layers299 × 127 mmLaunch, the printed circuit board in 3D

    Launch

    system76/launch

    System76 Launch Configurable Keyboard

    385 parts1.4kGPL-3.0
  • 4 layers53 × 42 mmMioLink, the printed circuit board in 3D

    MioLink

    Misaka0x2730/MioLink

    ARM JTAG/SWD debugger (BlackMagic port) based on RP2040.

    117 parts30GPL-3.0
  • 2 layers353.1 × 124.9 mmSkeleton68rev2, the printed circuit board in 3D

    Skeleton68rev2

    skeletonkbd/Frost68

    252 parts5

Questions

How big is the Open TraceV1 PCB?

It measures 43 × 32.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Open TraceV1 use?

34 parts, built around the RP2040, SN74LVC245APW, W25Q16JVSSIQ and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Open TraceV1 KiCad files?

From the Shubhayu-Banerjee/Open-Trace repository on GitHub, at the commit this page was made from: the board is Open-Trace PCBs/V1/Open-TraceV1/Open-TraceV1.kicad_pcb and its schematic Open-Trace PCBs/V1/Open-TraceV1/Open-TraceV1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Open TraceV1 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Shubhayu-Banerjee before reusing the design.