
TB66 motordriver
Shubhampoddar960/Motor_Driver_Kicad
KiCad PCB designs for L298N and other motor driver boards

KiCad PCB designs for L298N and other motor driver boards
L298N design is an open-source printed circuit board by Shubhampoddar960, from the Shubhampoddar960/Motor_Driver_Kicad repository on GitHub. It is a 2-layer board of 47.5 × 46.1 mm with 25 parts on 16 nets, routed with 252 tracks and 16 vias.
It is built around the L298N. Its parts include 9 diodes, 7 connectors, 2 capacitors, 2 ICs and 1 resistor. It belongs with the robots and motor control boards of this library.
screenshots](screenshots/) folder.L298N\_design/L298N\_design.kicad\_pro.IN1, IN2 | 🔁 Direction control for Motor A |IN3, IN4 | 🔁 Direction control for Motor B |ENA, ENB | 🎚️ PWM speed control for Motors A and B |VS | 🔋 Motor supply voltage |GND | ⏚ Common ground |OUT1–OUT4 | ⚙️ Motor outputs |#-----------------------------------------------------------------------------------------------------------------------------------------------------------------| #-----------------------------------------------------------------------------------------------------------------------------------------------------------------|
A compact dual DC motor driver board designed in KiCad, built around the TB6612FNG driver IC. It includes reverse polarity protection and proper supply filtering, which makes it a good fit for robotics projects such as line followers and small robots. 🤖
| Parameter | Value |
|---|---|
| ⚡ Motor supply (VMOT) | 4.5 V – 13.5 V |
| 🧠 Logic supply (VCC) | 2.7 V – 5.5 V |
| 🔁 Continuous current per channel | 1.2 A (3.2 A peak) |
| 🎚️ PWM frequency | Up to 100 kHz |
| Pin | Signal | Description |
|---|---|---|
| 1 | AIN1 | Motor A direction input 1 |
| 2 | AIN2 | Motor A direction input 2 |
| 3 | PWMA | Motor A speed (PWM) |
| 4 | BIN1 | Motor B direction input 1 |
| 5 | BIN2 | Motor B direction input 2 |
| 6 | PWMB | Motor B speed (PWM) |
| 7 | STBY | Standby (HIGH = enabled) |
| Pin | Signal | Description |
|---|---|---|
| 1 | VMOT | Battery / motor |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1N4007 | LED_SMD:LED_0805_2012Metric | D1, D2, D3, D4, D5, D6, D7, D8 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H2, H3, H4, H5 |
| 2 | 220uf | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1, C2 |
| 1 | 12V | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-03_1x03_P5.08mm_Horizontal | J6 |
| 1 | 1K | LED_SMD:LED_0805_2012Metric | R1 |
| 1 | ENA | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | ENB | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | Input_Terminal | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J10 |
| 1 | KA78M05_TO252 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U2 |
| 1 | L298N | Package_TO_SOT_THT:TO-220-15_P2.54x5.08mm_StaggerEven_Lead4.58mm_Vertical | U1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D9 |
| 1 | Output1and2_ScrewTerminal | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J1 |
| 1 | Output3and4_ScrewTerminal | TerminalBlock_CUI:TerminalBlock_CUI_TB007-508-02_1x02_P5.08mm_Horizontal | J2 |
| 1 | jumper1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |

Shubhampoddar960/Motor_Driver_Kicad
KiCad PCB designs for L298N and other motor driver boards


pedro-ibs/trekking
Desenvolvimento de um robô rádio-controlado/autônomo da moralidade “tracker”

FabioNMI/C64PSU
A low-cost, lightweight and very reliable power supply for the Commodore 64

Khuzhin06/RoboForce
Тогда вы не зря зашли к нам, мы постараемся максимально подробно и быстро рассказать о нашем пути создания робота на ROS2 Jazzy и esp32,по этим материалам вы с легкостью сможете повторить этот проект.


CainPatel/diy-ert
A $150 four-electrode earth resistivity meter (Wenner array): Arduino, AD620, ADS1115. Documented failure-first as an engineering log.

dduarteCE/Robot-vacuum
Embedded Linux robotic vacuum system built with Yocto on Raspberry Pi 4, featuring autonomous navigation, audio playback, and remote control through a web interface.

It measures 47.5 × 46.1 mm and has 2 copper layers, 1.6 mm thick.
25 parts, built around the L298N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Shubhampoddar960/Motor_Driver_Kicad repository on GitHub, at the commit this page was made from: the board is L298N_design/L298N_design.kicad_pcb and its schematic L298N_design/L298N_design.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Shubhampoddar960 before reusing the design.