
BMS DisplaySide
Shreeichchha/EV-Battery-Management-System-
ESP32-based EV Battery Management System with EKF SoC estimation, CAN communication, passive cell balancing, and fault protection.

ESP32-based EV Battery Management System with EKF SoC estimation, CAN communication, passive cell balancing, and fault protection.
BMS 4 8 is an open-source printed circuit board by Shreeichchha, from the Shreeichchha/EV-Battery-Management-System- repository on GitHub, published under the MIT licence. It is a 2-layer board of 195 × 182.5 mm with 51 parts on 71 nets, routed with 439 tracks and 1 via.
It is built around the TJA1042T/3/1J, ADS1115IDGS and DS18B20, with the IRF3205 among its other parts. Its parts include 23 resistors, 8 ICs, 7 capacitors, 5 transistors and 5 connectors. It belongs with the power boards and the ESP32 boards of this library.
An ESP32-based Battery Management System (BMS) for lithium-ion battery packs, featuring real-time battery monitoring, Extended Kalman Filter (EKF) based State of Charge estimation, passive cell balancing, fault protection, and CAN bus communication.
Developed as a Minor Project at the Department of Electronics and Computer Engineering, Institute of Engineering, Thapathali Campus.
This project focuses on the design and implementation of a modular Battery Management System for monitoring and protecting lithium-ion battery packs.
The system continuously monitors cell voltage, pack current, and temperature and uses an Extended Kalman Filter (EKF) to estimate the battery State of Charge (SoC). Thermal compensation is incorporated to improve SoC estimation under varying temperature conditions.
The BMS also provides passive cell balancing, automatic fault detection, MOSFET-based battery isolation, CAN communication, and a TFT-based monitoring interface.
A lightweight two-state Extended Kalman Filter is implemented for real-time SoC estimation on the ESP32.
The EKF tracks:
The algorithm combines battery model predictions with measured terminal voltage and current to continuously correct the estimated SoC.
Experimental thermal characterization is also incorporated into the estimation process to account for temperature-dependent battery behavior.
The BMS transmits battery information over the CAN bus for communication with external monitoring and vehicle systems.
CAN messages include:
The system continuously checks the battery for abnormal operating conditions such as:
Critical battery faults activate the MOSFET-based isolation circuit to disconnect the battery pack.
Passive cell balancing is used during charging to reduce voltage imbalance between cells.
EV-Battery-Management-System/
│
├── Firmware/
│ ├── bms_updated.ino
│ └── display_side_updated.ino
│
├── Hardware/
│ ├── main_bms/
│ ├── display_board/
│ └── Proteus/
│
├── Docs/
│ ├── Battery Management System.pdf
│ └── Slide of BMS.pdf
│
└── README.mdThe project involved:
The completed system demonstrated real-time battery monitoring, EKF-based SoC estimation, CAN communication, and hardware protection on a functional BMS prototype.
Pramisha Rai
Samiksha Dhakal
Shreeichchha K.C.
Shristi Mallik
Er. Suwarna Lingden
Department of Electronics and Computer Engineering
Institute of Engineering, Thapathali Campus
The complete project report and presentation slides are available in the Docs folder.
Developed as a Minor Project for the Bachelor of Engineering program at IOE, Thapathali Campus.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8, R22 |
| 4 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R12, R15, R18, R20 |
| 4 | 330 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R11, R14, R17 |
| 4 | 39 | Resistor_THT:R_Axial_DIN0414_L11.9mm_D4.5mm_P15.24mm_Horizontal | R13, R16, R19, R21 |
| 4 | C | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C2, C3, C4 |
| 4 | NPN | Package_TO_SOT_THT:TO-92_Wide | Q2, Q3, Q4, Q5 |
| 4 | PC817 | Package_DIP:DIP-4_W7.62mm | U4, U5, U6, U7 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C7 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10 |
| 1 | 10uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C6 |
| 1 | 2200uF | Capacitor_THT:CP_Radial_D16.0mm_P7.50mm | C5 |
| 1 | 4.7K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R24 |
| 1 | ADS1115IDGS | ADS1115_MODULE:ADS1115 | U1 |
| 1 | Bridge Rectifier | Diode_THT:Diode_Bridge_Round_D9.8mm | D1 |
| 1 | CAN Lines | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-4-5.08_1x04_P5.08mm_Horizontal | J6 |
| 1 | Conn_01x04_Socket | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-5-5.08_1x05_P5.08mm_Horizontal | J1 |
| 1 | DS18B20 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-5.0-H_1x03_P5.00mm_Horizontal | J2 |
| 1 | ESP32 DEVKIT C | ADS1115_MODULE:ESP32-DEVKITC | J5 |
| 1 | Fuse | Fuse:Fuseholder_Clip-5x20mm_Littelfuse_519_Inline_P20.60x5.00mm_D1.00mm_Horizontal | 5A1 |
| 1 | INA219AxD | ADS1115_MODULE:INA219_Module | U2 |
| 1 | IRF3205 | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | LM7805_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U3 |
| 1 | Load Terminal | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | LoadTerminal1 |
| 1 | TJA1042T-3 | MCP2515:MCP2515 | U13 |
| 1 | Transformer (Output) | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-5.0-H_1x03_P5.00mm_Horizontal | J4 |

Shreeichchha/EV-Battery-Management-System-
ESP32-based EV Battery Management System with EKF SoC estimation, CAN communication, passive cell balancing, and fault protection.



xrayer2000/MashMachine
My own built brewing system for making wonderful beer at home

omerikinci/ELV1
Elektronik kör yük (electronic dummy load) cihazının ilk stabil versiyonu. 150 W ile sınırlandırılmış, 30 V / 10 A aralığını destekler.



G-Pereira/greenmobi-bms
A VESC compatible battery management system

It measures 195 × 182.5 mm and has 2 copper layers, 1.6 mm thick.
51 parts, built around the TJA1042T/3/1J, ADS1115IDGS, DS18B20 and IRF3205. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Shreeichchha/EV-Battery-Management-System- repository on GitHub, at the commit this page was made from: the board is Hardware/main_bms/BMS_4_8.kicad_pcb and its schematic Hardware/display_board/BMS_DisplaySide.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).