4 layers101.6 × 53.3 mm
2 layers101.6 × 53.4 mm
ArduinoDUE JSGO AJGL AGRG
SebassOR/PCB-ARDUINO-DUEDTCI
- Size
- 101.6 × 53.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 126
- Nets
- 193
- Pads
- 671
- Tracks, vias
- 1,132, 99
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 Apr 2026
- Updated
- 21 Apr 2026
Overview
ArduinoDUE JSGO AJGL AGRG is an open-source printed circuit board by SebassOR, from the SebassOR/PCB-ARDUINO-DUE repository on GitHub. It is a 2-layer board of 101.6 × 53.4 mm with 126 parts on 193 nets, routed with 1,132 tracks and 99 vias.
It is built around the ATSAM3X8EA-AU, ATMEGA16U2-MU and MPM3610AGQV-P, with the SN74LVC1G125DCK, LM358 and LM1117MP-3.3 among its other parts. Its parts include 43 capacitors, 25 resistors, 14 connectors, 7 diodes and 6 ICs. It belongs with the AVR (ATmega, ATtiny) and SAM D and SAM boards of this library.
Main components
12
ATSAM3X8EA-AU
LQFP-144(20x20)-40℃~+85℃ 1.62V~3.6V 100KB 103 12bit 12bit 32 Bit 512KB 84MHz ARM Cortex-M3 Built-in FLASH LQFP-144(20x20) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
ATMEGA16U2-MU
QFN-32-EP(5x5)-40℃~+85℃ 16KB 16MHz 2.7V~5.5V 22 512Byte 512Byte 8 Bit AVR Built-in FLASH QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MPM3610AGQV-P
QFN-20(3x5)-40℃~+125℃ 1 1.2A 1.6mm 2MHz 300uA 3mm 4.5V~21V 5mm 800mV~18.48V Short Circuit Protection、Over-temperature protection、Over Current Protection、Under Voltage Protection、Automatic fault recovery、Programmable output voltage、Light load efficient mode Step-down type QFN-20(3x5) DC-DC Power Modules ROHSMonolithic Power SystemsDC-DC Power Modules
SN74LVC1G125DCK
SC-70-5-40℃~+125℃ 0.6ns@3.3V,15pF 1 1 1.65V~5.5V 10uA 32mA 32mA 74LVC Tri-State Unidirectional SC-70-5 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
LM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational Amplifier
LM1117MP-3.3
SOT-2230℃~+125℃@(Ta) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA 99uVrms Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
CG0603MLC-05E
0603-55℃~+125℃ 0.2pF 1 10nA 30V 5V Bidirectional IEC 61000-4-2 0603 ESD and Surge Protection (TVS/ESD) ROHSBournsVaristors
MH2029-300Y
0805-55℃~+125℃ 1 30Ω@100MHz 3A 3mΩ ±25% 0805 Ferrite Beads ROHSBournsFerrite Beads
PMV48XP
SOT-23-55℃~+150℃ 1 P-Channel 15W 190pF 1V 20V 4.1A 7.8nC@4.5V 740pF 75mΩ@2.5V SOT-23 MOSFETs ROHSTECH PUBLICMOSFETs
CD1206-S01575
1206-55℃~+125℃ 150mA 1V@50mA 2.5uA@75V 400mW 4A 4ns 75V Standalone 1206 Switching Diodes ROHSBournsSwitching Diodes
MF-MSMF050-2
1812-40℃~+85℃ 100A 150mΩ 15V 1A 1Ω 3.2mm 5.4mm 500mA 1812 Resettable Fuses ROHSBournsResettable FusesBC847B
SOT-23-65℃~+150℃ 1 NPN 100MHz 100mA 200 200mV 250mW 45V 5uA 6V NPN SOT-23 Bipolar (BJT) ROHSNexperiaBipolar (BJT)
Parts
126| Qty | Value | Footprint | References |
|---|---|---|---|
| 21 | 100nF | Capacitor_SMD:C_0201_0603Metric | C4, C10, C12, C13, C14, C15, C16, C17, C18, C19, C22, C23, C24, C30, C31, C34 +5 |
| 8 | 22uF | Capacitor_SMD:C_1206_3216Metric | C1, C2, C3, C7, C8, C11, C29, C32 |
| 6 | 22pF | Capacitor_SMD:C_1206_3216Metric | C20, C25, C26, C27, C28, C33 |
| 5 | CG0603MLC-05E | FOOTPRINT:VARC1608X56N | RV1, RV2, RV3, RV4, RV5 |
| 4 | 1K | Resistor_SMD:R_0402_1005Metric | R2, R14, R15, R23 |
| 3 | 0R | Resistor_SMD:R_1206_3216Metric | R8, R11, R18 |
| 3 | 100K | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN2, RN3 |
| 3 | 10K | Resistor_SMD:R_0402_1005Metric | R7, R13, R18USBBOOTEN1 |
| 3 | MH2029-300Y | FOOTPRINT:L0805 | L1, L2, L6 |
| 3 | PMV48XP | Package_TO_SOT_SMD:SOT-23 | T1, T2, T3 |
| 3 | Yellow | LED_SMD:LED_0201_0603Metric | D3, D6, D7 |
| 2 | 100k | Resistor_SMD:R_0402_1005Metric | R10, R16 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C36, C37 |
| 2 | 19k1 0.1% | Resistor_SMD:R_0603_1608Metric | R28, R29 |
| 2 | 22R | Resistor_SMD:R_0402_1005Metric | R40, R41 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C39, C40 |
| 2 | 39R 1% | Resistor_SMD:R_1206_3216Metric | R5, R6 |
| 2 | 47346-0001 | FOOTPRINT:MOLEX_47346-0001 | J10, J11 |
| 2 | YELLOW | LED_SMD:LED_0201_0603Metric | RX1, TX1 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C50 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C35 |
| 1 | 12MHZ-12pF-k7 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 157sw | Button_Switch_SMD:SW_Push_1P1T_NO_Vertical_Wuerth_434133025816 | SW1 |
| 1 | 16MHZ | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y4 |
| 1 | 1K5 | Resistor_SMD:R_Array_Convex_4x0603 | RN4 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C38 |
| 1 | 22Pf | Capacitor_SMD:C_1206_3216Metric | C21 |
| 1 | 32768KHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | 47uF | Capacitor_SMD:CP_Elec_6.3x5.4 | PC1 |
| 1 | 56K | Resistor_SMD:R_0603_1608Metric | R31 |
| 1 | 6K8 | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 75K | Resistor_SMD:R_0402_1005Metric | R17 |
| 1 | AD7-0 | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J3 |
| 1 | ATSAM3X8EA-AU | ATSAM3X8EA-AU (1):QFP50P2200X2200X145-144N | U4 |
| 1 | ATmega16U2-M | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U1 |
| 1 | Barrel_Jack_MountingPin | Connector_BarrelJack:BarrelJack_Horizontal | GND1 |
| 1 | CD1206-S01575 | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | COMMUNICATION | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J6 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J13 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical | J14 |
| 1 | Conn_02x18_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x18_P2.54mm_Vertical | J12 |
| 1 | Green | LED_SMD:LED_0201_0603Metric | D4 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J5 |
| 1 | ICSP1 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J8 |
| 1 | IOREF | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | JP5 | Connector_PinHeader_2.00mm:PinHeader_2x02_P2.00mm_Vertical | J9 |
| 1 | JUMPER | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP1 |
| 1 | L2 | Inductor_SMD:L_0805_2012Metric | LLMH2028-300Y1 |
| 1 | LM1117MP-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | LM358 | Package_SO:MSOP-8_3x3mm_P0.65mm | U2 |
| 1 | MF-MSMF050 | Fuse:Fuse_1812_4532Metric | F2 |
| 1 | MFMSMR050-2 | Inductor_SMD:L_1812_4532Metric | F1 |
| 1 | MPM3610AGQV-P | FOOTPRINT:CONV_MPM3620AGQV-P | U5 |
| 1 | MSS1P3L-M3/89A | Diode_SMD:D_MicroSMP_AK | D1 |
| 1 | PIN HEADER | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J7 |
| 1 | PWMH | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J1 |
| 1 | PWMI | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | R_Network04_Split | Resistor_SMD:R_Array_Convex_4x0603 | RN5 |
| 1 | SN74LVC1G125DCK | Package_TO_SOT_SMD:Texas_R-PDSO-G5_DCK-5 | IC10 |
| 1 | SS1P3L | Diode_SMD:D_MicroSMP_AK | D5 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC7xxJ | SW2 |
| 1 | bc847b | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | l1 | Inductor_SMD:L_0805_2012Metric | LMH2028-300Y1 |
Similar boards
- 2 layers
DuePi
radioelf/Arduino-Due-mod-for-GPIO-compatible-Raspberry-Pi
PCB arduino Due para DuePi y Gpio Raspberry Pi
120 parts1 - 2 layers101.6 × 53.3 mm
Arduino mega 2560 rev3e
javachaos/arduino_simulator
arduinosimulator is a standalone AVR simulation and board-tooling workspace.
72 partsGPL-3.0 - 2 layers101.6 × 53.3 mm
- 2 layers68.6 × 53.3 mm
Arduino Mega 2560
ded811/Mega-Uno-2560
An Arduino-compatible ATmega2560 development board in the Arduino Uno form factor
62 parts1 - 4 layers221.5 × 130.8 mm
MEP MAXI-85V-1-REV-2-Interface Board
JGilcreast/MetalHead
An opensource firmware and software drop-in replacement for the 85V Automatic Stirrup Bender by CRS Specialties Inc. ...short story behind the name...
407 parts - 2 layers
New Atmega 2560
RoyZeng0317/kicad
This is the kicad circuit diagram layout, it's have more layout in here.
74 parts - 4 layers48.3 × 17.8 mm
Arduino Micro
sabogalc/KiCad-Arduino-Boards
A collection of Arduino boards recreated from scratch in KiCad. Legacy USB connectors have been replaced with USB-C where applicable.
48 parts95WTFPL
Questions
How big is the ArduinoDUE JSGO AJGL AGRG PCB?
It measures 101.6 × 53.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ArduinoDUE JSGO AJGL AGRG use?
126 parts, built around the ATSAM3X8EA-AU, ATMEGA16U2-MU, MPM3610AGQV-P and SN74LVC1G125DCK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ArduinoDUE JSGO AJGL AGRG KiCad files?
From the SebassOR/PCB-ARDUINO-DUE repository on GitHub, at the commit this page was made from: the board is ArduinoDUE_JSGO_AJGL_AGRG/ArduinoDUE_JSGO_AJGL_AGRG.kicad_pcb and its schematic ArduinoDUE_JSGO_AJGL_AGRG/ATSAM3X8EA-AU.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ArduinoDUE JSGO AJGL AGRG design in my own project?
Its repository states no licence, so its author keeps all rights: ask SebassOR before reusing the design.